PALMER GA 03 Splitter for Guitars Y-Box Active

117.79 incl. GR VAT

Available on backorder

EAN: 4049521049255
Installments calculation
CompareAdd to wishlist Submit Better Price
  • Clinking input with 1 Mohm input impedance
  • Output AMP1 as parallel circuit
  • Output AMP2 is electronically converted with a subsequent transformer stage
  • Operation with 9V battery recommended
  • 5 years manufacturing guarantee
  • Clinking input with 1 Mohm input impedance
  • Output AMP1 as parallel circuit
  • Output AMP2 is electronically converted with a subsequent transformer stage
  • Operation with 9V battery recommended
  • 5 years manufacturing guarantee

 

Read more

“When I run my guitar into two amps simultaneously, I always get a loud hum”. This is a rather common problem, often discussed in the technology section of relevant industry magazines. The Palmer Y box is the solution. Converting the hi-Z guitar signal, the FET input circuitry also drives a transformer which routes the ungrounded signal to the output to eliminate ground loop hum. 9V battery operation is recommended.

The PGA03 Y-box can also be used as a line driver for long cable runs. Also, the PGA03 features a phase reverse switch for the AMP 2 output when using pre-amps or amps that are out of phase.

 

Technical specifications:

Product type
Splitters
Split type
1 in 2
Inputs
1
Input connectors
6.3 mm jack
Adjustable input
no
Number of split-outputs per canal
1
Output connectors
6.3 mm jack
THRU outputs/channel
1
Transformer isolated outputs
Yes
Adjustable output
no
Controls
ground lift, phase
Indicators
Power
Operating voltage
9 V block, 9 V DC power supply
Width
125 mm
Depth
80 mm
Height
45 mm
Cabinet material
sheet steel
Cabinet surface
Powder coated
Weight
0,528 kg

Optional Power Supply PW9V

Weight 0.25 kg

Reviews

There are no reviews yet.

Be the first to review “PALMER GA 03 Splitter for Guitars Y-Box Active”

Your email address will not be published. Required fields are marked *

Quick Comparison

PALMER GA 03 Splitter for Guitars Y-Box Active removeGRANITE T-1C Drum Stool 280mm removeKONIG & MEYER 14330 "Jazz" Saxophone stand removePALMER AUDIO PCABM CAB M - Passive Cabinet Merger removeQUIKLOK BS-317 Low Profile Amp Stand removeMOTU ZBox Amplify guitar tone remove
NamePALMER GA 03 Splitter for Guitars Y-Box Active removeGRANITE T-1C Drum Stool 280mm removeKONIG & MEYER 14330 "Jazz" Saxophone stand removePALMER AUDIO PCABM CAB M - Passive Cabinet Merger removeQUIKLOK BS-317 Low Profile Amp Stand removeMOTU ZBox Amplify guitar tone remove
Imagepalmer audio GA03_splitter box guitars activegranite_t_1c_adjustable_seat
SKUPGA03M29GN00002M19KM00023PCABMG30QL00002zbox
Rating
Price 117.79 incl. GR VAT 39.00 incl. GR VAT 49.00 incl. GR VAT 28.51 incl. GR VAT 49.00 incl. GR VAT48.39 incl. GR VAT
Stock

Available on backorder

Only 1 left in stock (can be backordered)

In stock

Available on backorder

In stock

In stock

AvailabilityAvailable on backorderOnly 1 left in stock (can be backordered)In stockAvailable on backorderIn stockIn stock
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
  • Clinking input with 1 Mohm input impedance
  • Output AMP1 as parallel circuit
  • Output AMP2 is electronically converted with a subsequent transformer stage
  • Operation with 9V battery recommended
  • 5 years manufacturing guarantee
Adjustable drum stool, diameter 280mm
Content
"When I run my guitar into two amps simultaneously, I always get a loud hum". This is a rather common problem, often discussed in the technology section of relevant industry magazines. The Palmer Y box is the solution. Converting the hi-Z guitar signal, the FET input circuitry also drives a transformer which routes the ungrounded signal to the output to eliminate ground loop hum. 9V battery operation is recommended. The PGA03 Y-box can also be used as a line driver for long cable runs. Also, the PGA03 features a phase reverse switch for the AMP 2 output when using pre-amps or amps that are out of phase.  
Technical specifications:
Product type
Splitters
Split type
1 in 2
Inputs
1
Input connectors
6.3 mm jack
Adjustable input
no
Number of split-outputs per canal
1
Output connectors
6.3 mm jack
THRU outputs/channel
1
Transformer isolated outputs
Yes
Adjustable output
no
Controls
ground lift, phase
Indicators
Power
Operating voltage
9 V block, 9 V DC power supply
Width
125 mm
Depth
80 mm
Height
45 mm
Cabinet material
sheet steel
Cabinet surface
Powder coated
Weight
0,528 kg
Optional Power Supply PW9V
Adjustable drum stool, diameter 280mm
Drums seat adjustable in height (500mm-630mm), Anatomical round saddle with a diameter of 280mm, Tube diameter: 28.6mm/25mm, Legs double reinforced with anti-slip protectors at the ends.

Practical, easy to use and stable stand for Eb alto saxophones. Solid square-type aluminum tubes with a large central locking screw, protective rubber bumps where the stand connects with the saxophone body and the bell. Embedded foot end caps. Folds compactly, can be transported in the supplied velour bag in the saxophone bell.

  • Weight: 0.3 kg
  • Height: 310 mm

The concept behind the cab merger may be very simple, but it fills an important gap!

Have you ever wanted to connect two guitar cabinets to one amplifier output? The PCABM makes it possible.

In addition, you can select whether the cabinets should be wired in parallel or series  with one another. For example, if you interconnect two 8 ohm cabinets.  The PCABM offers you two resulting impedances to choose from: 4 ohms (parallel) or 16 ohms (serial). The device is passive and does not affect the tone in any way.

  • Type: passive
  • Number of inputs: 2
  • Input connections: 6.3mm jack
  • Number of outputs: 2
  • Output connections: 6.3mm jack
  • Cabinet material: die-cast aluminium
  • Case surface: powder-coated
  • Width: 105 mm
  • Depth: 35 mm
  • Height: 35 mm

Double-Brace, Low Profile Stand for Large Amps  and Combos Height adjustment range Front tier: 8.25" to 11" - 21 to 28 cm Back tier: 11.4" to 18.6" - 29 to 47.2 cm Width: 19.3" - 49 cm Folded height: 22" - 56cm Frame tube size: 20 x 15 mm Tier tube size: 28mm Weight capacity: 100lb - 45.2 kg Weight: 6.6 lb - 3 kg

ZBox Overview Take back your guitar tone! Today's guitar amp modeling plug-ins are simply amazing in their ability to faithfully model real guitar amplifiers. From IK Multimedia's Amplitube, to Waves, to Native Instruments, to Line 6, to Digital Performer's included Custom '59, you can plug your guitar directly into your audio interface, dial up a guitar tone in your plug-in software, and play. The sound is simply stunning. But wait. They're ALL MISSING SOMETHING. In fact, they're missing a crucial element of the signal path that simply cannot be modeled in software: the proper input impedance of a real guitar amplifier. When you plug your guitar into your audio interface, the interface's impedance does not match the typical levels found on a real guitar amplifier. The result? No matter how hard you try, you'll never quite be able to replicate the true sound and "feel" of playing into a real guitar amp. The sound will be just a little more thin and unresponsive than the real thing. The solution? ZBox! ZBox matches the output impedance (”Z”) of your guitar to the impedance of a non-amp input, such as the mic/instrument preamp inputs on your audio interface. Without proper impedance matching, your guitar wonʼt sound natural or "feel right”. ZBoxʼs unique advantage? Authentic matching circuits that emulate the two-jack switching network found on many classic amplifiers, complete with analog simulation of the input tube grid. Only ZBox delivers the most authentic amplifier impedance matching available for the absolute truest sound and "feel” from your guitar. ZBox is the "missing link” for digital guitar processing, providing the hardware-driven input characteristics required to truly emulate a real guitar amp. If you use Digital Performer's Custom 59 amp model plug-in, or a third-party guitar plug-in product like IK Multimedia Amplitube, Waves GTR, Native Instruments Guitar Rig, or similar guitar modeling software, use ZBox to further enhance the authenticity of the tones you play from these products! Just plug your guitar into ZBoxʼs Lo-Z or Hi-Z input (whichever sounds better), and plug the ZBox into the guitar input on the destination device (audio interface, wireless box, mixer, recorder, PA, etc.) as shown. Guitar inputs on audio interfaces, mixers, PAs, wireless transmitters and other similar devices (often labeled "instrument”) usually have impedances that differ significantly from most guitar amps. This mismatch can make your guitar sound too bright, thin and brittle. ZBox provides the proper input impedance levels to match your guitarʼs output signal. The result? Your guitar sounds like it is connected to a real guitar amp and has a much warmer tone and authentic "response.” This is especially true when using digitally modeled guitar processing software (plug-ins) on your computer, audio interface, digital mixer, etc. To support a wide range of guitars, ZBOX provides authentic "Hi-Z” and "Lo-Z” inputs, just like the ones found on many classic guitar amps, complete with analog simulation of the input tube grid.
Weight0.25 kg2 kg0.30 kg0.13 kg3.10 kg7.00 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 0.25 kg
Weight 2 kg
Weight 0.30 kg
Weight 0.13 kg
Weight 3.10 kg
Weight 7.00 kg