PALMER PRMMS Pro PRMMS – Microphone Splitbox 4 Channel

• Each channel: Input: female XLR type
• Outputs: 1 parallel male XLR type, 2 transformer isolated male XLR type
• Nominal impedance for inputs/outputs: 200
• Max. input level: + 6 dBu

Practical distributor with 1 input and 6 outputs

• Extends every mixer with additional outputs
• 1 stereo XLR input
• 6 stereo zone outputs (XLR)
• Each zone with level control and mono switch
• LED display of signal input and mono/stereo mode
• (19") 48.3 cm rack installation 1 U
• For application areas such as: Installation; restaurants, bars and hotels; sports centres/gyms

Package contents

• 1 x device, 1 x power cord, 1 x user manual

1215 Dual 15-Band Graphic Equalizer

The dbx 12 Series were designed to meet the needs of the most
demanding sound reinforcement environments, while offering the
simplicity of straightforward controls. The 1215 provides standard
features like dual channels, 15 2/3 octave bands, ISO frequency
centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per
octave low-cut filters, but also includes other thoughtful features.
These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut
range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS
connectors for installation ease; balanced inputs and outputs for quiet
operation; and chassis/signal ground lift capabilities for quick hum isolation.
The visionary design of the dbx 12 Series makes your job easier.

The dbx 12 Series Equalizers were precision engineered to provide years
of maintenance-free operation in any application. The magnetically isolated
transformer, electronically balanced/unbalanced inputs and servo balanced/
unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire
relay bypass with 2 second power up delay were steps our engineers took
to ensure compatibility for all installations. Only the best components were
utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR
(ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel
crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail
is contained in a 2U steel/aluminum chassis.

•   Switchable boost/cut ranges of ±6 or ±15 dB
•   Electronically balanced/unbalanced inputs
•   Servo balanced/unbalanced inputs
•   RF filtered inputs and outputs
•  XLR, Barrier Strip, and 1/4" TRS connectors
•  -12dB/+12dB input gain range
•  18dB/octave 40Hz Bessel low-cut filter
•  Chassis/signal ground lift capability
•  Internal power supply transformer
•  Power-off hardwire relay bypass with 2-second power-up delay

• XLR balanced ins and outs
• Mode switch for stereo 2-way or mono 3-way operation
• Low frequency summed (subwoofer) output
• x10 range switch on both channels
• 40Hz high pass (low cut) filter both channels
• Phase reverse switch on all outputs
• Individual level controls on all outputs
• 24dB per octave Linkwitz-Riley filters (the professional standard)
• Stereo/Mono status LEDs indicate the selected mode
• dbx® 2 year parts and labor as standard
• CSA NRTL/C approved
• CE compliant

About the DI6s
It's a fact of audio life that a lot of equipment that has to be connected to
professional audio systems isn't impedance or level compatible.
Interfaces Unlimited
Tape/cassette/DVD/CD decks, audio for video, drum machines, synthesizers,
bass guitars, computers; at some stage all these need linking up to Balanced
inputs, whether the application is Live sound, Studio or Broadcast.
To solve these problems, we've developed the DI-6s:

Six active D.I. (Direct Injection) boxes,
plus a 6 into 1 Line Mixer,
plus a 1 to 6 Splitter,
All of this in a compact, all steel 1 RU package.

A Pro Audio Toolbox
This unique and flexible audio toolbox allows Six independent unbalanced
audio sources to easily and quietly interface with Balanced pro audio systems,
either to individual channels or summed down to one Master output.
But that's not all. By pressing a single switch on the rear panel the DI6s will
change from being Direct Boxes and a Mixer to being a 6 way Splitter (line
distribution amplifier). Now it will split an incoming signal to 6 individual outputs
or zones.
On the front panel, each channel has 2 IN/OUT jacks, a level control from infinity
(off) through 0dB to +15dB gain, and a Clip indicator LED.The Master section has
a Master volume control and status LEDs indicating whether the unit is in DI or
Splitter mode. In addition, as on all ARX single rack unit equipment, each channel
has a numbered marker panel ('scribble strip') you can write on for easy confirmation
of channel assigns.
Balanced Outputs
On the rear, each channel has an XLR Balanced output, with associated Ground lift
switch and status LED, to isolate the chassis and electronic grounds.
The Master section has both Balanced XLR and Unbalanced Jack outputs. In addition
there is a Balanced XLR input with a switch to put the unit in either DI or Splitter mode.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to the
unit via a removable power lead and standard 3 pin IEC connector, with built-in fuse and
voltage change switch.
With so many handy functions, plus a true 'user friendly' layout, it's no wonder people call
the DI-6s 'A total Audio Patching System in 1 RU!'
You'll never compromise on Quality when you choose ARX

Features
Unique Pro Audio problem solver
Six Direct boxes, Splitter and Line Mixer in one unit
Multi mode unit: Six in, Six out; Six in, One out; One in, Six out
Individual Output Ground lift switches
Up to +15dB Gain available per channel
Balanced XLR Outputs; High Impedance Jack Ins and Outs
Flawless performance in any audio environment

T E C H N I C A L S P E C I F I C A T I O N S

Channels 1 - 6
High Z Input Impedance 2.2 Meg Ohm
Max Channel Gain 15dB
Clip LED Illuminates 1dB prior to clip
Direct Output Impedance 300 ohms Balanced
Max Input Level +20dB
Max Output Level +21dB
Signal to Noise -96dB(unity gain)
Frequency Response 20Hz to 20KHz, ±0.5dB
Distortion < 0.004%, 1KHz, +4dB
Output Connector 3 pin XLR
Master Section
Output Impedance 300 Ohms Balanced
Max Output Level +21dB
Signal to Noise -90dB (unity gain)
Frequency Response 10Hz to 20KHz, ±0.5dB
Distortion < 0.004%, 1KHz, +4dB
Output Connector 3 pin XLR
Splitter Section
Maximum Level + 20dB
Input Impedance 20 KOhms, Balanced
Input Connector XLR
Frequency Response 10Hz?20KHz ±0.5dB
AC Power 100-120, 220-240 V AC, 8 VA
Size 19?W x 6?D x 1??H, 482 x 155 x 44mm
Weight 2.2 Kg (5 lbs)

Front Panel Controls
Hi Impedance (Hi Z) insulated jack Input and Output
connectors
Level control with up to +15dB of Gain available
Clip LED indicator
Marker panels for labelling DI assigns
Master Level controls
Rear Panel
Balanced XLR Outputs
Individual Audio Ground Lift switches and status LEDs
XLR and jack Master Outputs
XLR Input for splitter
Splitter/DI + Mixer mode switch
AC input connector, with voltage switch and fuse. 

• Error proof operation to smooth uneven levels, add sustain to guitars, fatten drums or tighten up mixes
• New gate timing algorithms ensure the smoothest release characteristics
• Program-adaptive expander/gates
• Great sounding dynamics control for any type of program material
• Separate precision LED displays for gain reduction, compression threshold and gate threshold allow quick, accurate setup
• Stereo or dual-mono operation
• Balanced inputs and outputs on 1/4" TRS and XLR connectors
• Side Chain insert
• Classic dbx® "Auto" mode