Content |
- Two-way bi-amplified analog amp powered speaker system
- DX 14 compression driver, with 1.4 inch titanium diaphragm
- 15 heavy-duty woofer
- DSP processing is 64 bit double-precision
- Dynamic bass boost function
- Input is via a combo female XLR and 1/4" TRS phone jack with balanced input
- Thru output is via a male XLR jack
- Exclusive Quadratic Throat Waveguide technology, 110 by 80 degree coverage
- A Mic/Line switch provides for two different gain settings
- Rugged plastic injection-molded trapezoidal enclosure
- DSP I/O is at 96 kHz and 24 bits, with low-jitter, professional grade components
- Cabinet has dual rear corner angled sides for floor monitor use.
- Fan cooled for maximum reliability
- Full-coverage perforated steel grille, with powder coat finish
- Multiple Factory Preset EQ settings for the DSP crossover system
- Pole mount molded-in for 1 3/8" diameter poles
- User Preset EQ storage provisions allow storing custom presets for later recall
- Weight Unpacked: 19.1 kg
- Weight Packed: 23.133 kg
- Width Packed: 47.9425 cm
- Height Packed: 77.47 cm
- Depth Packed: 44.60748 cm
|
GENERAL
The PSA Systems JB-15 is the active variant of the PS-15. This active full range speaker has a built-in amplifier of the bi-amp type and delivers 300 watts RMS. In combination with the active crossover the audio signal is distributed efficiently on a woofer and tweeter. The PSA-15 has a 15-inch woofer, which effortlessly displays the low frequencies, starting at 40Hz. Here he is fed with less than 245 watts. The 1.35-inch compression driver takes it high for his account and get 55 watts of power. This was in fact the RMS power; peaks that are higher are no problem for the amplifier. You are assured of a solid, non-pinched sound.
JB Systems PSA-15 Speaker: Polypropylene
The PSA-15 has a smooth shaped casing made of polypropylene. A light but very strong type of plastic, which is good for long-term protection of the internal components. In addition, he is very practical, with a built-in carrying handle, M8 mounting points, a 35 mm stand adapter and support for monitor use. The latter is excellent as possible, thanks to the angle of the housing.
CONNECTIONS
The back contains the connections with two microphone inputs (XLR, 6.3 mm jack) and a line input (XLR, RCA). The inputs and outputs are balanced. As per the level can be controlled, there is also a master volume and a two-band tone control devices. The PSA 15 is very suitable for mobile use and permanent installation and can be used as PA speaker and be used as a monitor. Monitor Brackets are included. |
Product Features:
High-Power 1000-Watt 2-way PA sound reinforcement speaker system for live and playback applications
Ultra-compact and lightweight system delivers excellent sound even at extreme sound pressure levels
High-performance MP3 player included to play audio files via USB stick
"Wireless-ready" for high-quality BEHRINGER digital wireless system (not included)
2-channel mixer with individual Mic/Line inputs, Volume controls and Clip LEDs
Dedicated 2-band EQ plus integrated sound processor for ultimate system control and speaker protection
Revolutionary Class-D amplifier technology: enormous power, incredible sonic performance and super-light weight
Extremely powerful 15'' long-excursion driver provides incredibly deep bass and acoustic power
State-of-the-art 1.35'' aluminum-diaphragm compression driver for exceptional high-frequency reproduction
Ultra-wide dispersion, large-format exponential horn
Additional Line output allows linking of additional speaker systems
Versatile trapezoidal enclosure design allows different positioning:
- Stand mounting with 35-mm pole socket
- Tilts on its side for use as a floor monitor
Ergonomically shaped handles for easy carrying and setup
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany
User's Manual
|
The Titan™ 15 Active is a self-powered, two-way professional loudspeaker system incorporating a high grade Bi-Amp Class D and Class A/B Amplifiers. The model also has intelligent electronics, such as full protection system: DC, overload, short circuit, thermal, On / Off mute and LF / HF Limiters, which protects the system from overload and allows reliable operation right up to the power limit.
The bottom of the Titan™ 15 ACTIVE provides a convenient built in pole mount socket for easy mounting on a standard 35mm diameter speaker stand pole.
The speaker stand receptacle features a locking screw to ensure stability.
Ten M8 threaded rigging points are provided for a variety of safe flying
configurations with four of these inserts available, bottom-mounted, in an OmniMount® 60.0 bracket footprint.
Mixer and Controls
The Titan™ 15 ACTIVE provides basic mixing functions with a variety of input options. Two inputs with separate level controls and a common equalization section allow for overall balance and tonal characteristic control. Easy interfacing to external mixers and processors provide for easy expansion to larger, more sophisticated systems.
|
SPECIFICATIONS
| MODEL | TITAN 15 ACTIVE | GENERAL INFO |
| System type | Active 15" 2-way Bi-Amplified | Frequency response +/- 3db | 50-20kHz | HF SECTION |
| Hf type | Titanium Compression Driver | Horn dispersion (H x V) | 90° x 60° | Hf exit size mm / inches | 25mm / 1“ | PHYSICAL FEATURES |
| Enclosure Material | Injection Moulded Polypropylene | Enclosure Colour | Grey or White or Black | Size (mm/inches) | 381mm / 15“ | IN / OUT PANEL (speaker Level) |
| Input connector | XLR - 1/ 4" Combo jack | AMPLIFIER POWER |
| Power On Protection | Power switch on / off mute | Thermal Protection | Amplifier shutdown, auto reset | Low Line Voltage Shut Down | 60% Nominal line voltage | Driver Protection | Independent LF and HF limiters | DC Protection | Yes | Short Protection | Yes | Controls | High (±10dB) 10kHz Shelving | Dimensions (HxWxD) |
| mm | 708.3mm x 477.8mm x 401.77mm | inches | 27.9" x 18.8" x 15.8“ | Microphone / Transmitter |
| Maximum Input Level | +22dBu | Impedance | 4 Ω | MIXER MODEL |
| INPUT IMPEDANCE | Balanced: 20k ohms Unbalanced: 10k ohms | Clip Limiter | Turns on approx 350W output | Limiter Indicator | Red LED | Power Indicator | Red LED | AC Power details |
| Power Supply | High Efficiency Switching Mode Power Supply | AC Power Options | AC100~120V / 220~240V, 50 / 60Hz | Power On Indicator | LED | Rigging / Bracket / | 10 M8 threaded inserts including 4 | Mounting Options | M8 threaded inserts on bottom in OmniMount 60.0-type footprint Pole-mount receptacle with lock screw 2 carry handles (one on each side) Optional wall-mount bracket | Impedance Balanced | Balanced: 1k ohm - Unbalanced: 500 ohm | Line Output |
| Line Output Connector | Switchable LOOP / MIX Balanced Male XLR | Input A - type | Switchable balanced mic or line level input | Input Sensitivity | Mic: -36dBu (-38.2dBv or 12.28mVrms)
Line: +4dBu (1.78dBv or 1.228Vrms) | Maximum Input Level | +22dBu | Input Connector | XLR - 1/ 4" Combo jack | Input Impedance | Balanced: 20k ohms Unbalanced: 10k ohms | Input B - type | Line level input | Input Sensitivity | XLR - 1/4" Combo jack: 1.78dBv or 1.228Vrms
RCA: 0dBu (-2.2dBv or 0.775Vrms) | Maximum Input Level | +22dBu | Input Connectors | Combo jack: 1/4" - XLR / Summed dual RCA jacks | Bass Response Optimizer |
| (“BRO“™) circuit | +5dB at 60Hz | Subsonic Filter | 30Hz, Second-order filter | Amplifiers |
| Low-Frequency (Class D) | Rated 350W RMS, 700W Peak | High- Frequency (Class A/B) | Rated 70W RMS, 140W Peak | Electronic Crossover | 24dB/octave Linkwitz-Riley | Crossover Frequency | 1.8kHz | Controls | High (±10dB) 10kHz Shelving | Equalization | Low (±10dB) 100Hz Shelving | DIMENSIONS & WEIGHT |
| Net weight ( kg / lbs ) | 23.7kg / 52.67lbs | Gross weight ( kg / lbs ) | 26.94kg / 59.27lbs | |
|
Features
400 Watt digital bi-amplification
129 dB max spl
Wide dispersion 90 x 60 constant directivity horn
15" High power woofer, 3" voice coil
2" Titanium dome, high frequency driver
DSP processing, boost eq, soft limiter and protection
Xlr/jack input, xlr signal output
Acoustical Specifications
Frequency Response -3 dB: 45 Hz ÷ 20 kHz
Max SPL: 129 dB
Horizontal coverage angle: 90°
Vertical coverage angle: 60°
Compression Driver: 2" 2.5" voice coil
Woofer: 15" 3" voice coil
Input/Output Section
Input connectors: xlr-jack
Output connectors: xlr
Processor Section
Crossover frequencies: 1300 Hz
Controls: Flat, Boost
Amplifier Specifications
Total power: 400 W
High frequencies: 100 W
Low frequencies: 300 W
Cabinet
Cabinet Material: Composite PP
Handles: 1 on top, 2 on sides
Pole Mount/Cap: yes
Grille: steel
Physical Specifications
Height: 708/27.8 mm/inch
Width: 437/17.2 mm/inch
Depth: 389/15.3 mm/inch
Net Weight: 26/57.32 kg/lbs
|
The new ETX Powered Loudspeakers family builds upon the industry-leading innovation and 85-year heritage of Electro-Voice audio engineering to offer the most advanced professional portable powered loudspeakers available today.
A versatile high-end choice for live entertainment venues, rental companies, pro musicians and DJs, and installed sound, the ETX Powered Loudspeakers family features three two-way models (10-inch, 12-inch and 15-inch, all with a precision HF titanium compression driver), a three-way model (15-inch with a 6.5-inch MF driver and a precision HF titanium compression driver) and two subs (15-inch and 18-inch drivers).
Positioned above the ZLX and Live X families respectively, ETX Powered Loudspeakers complete a trio of recent EV portable loudspeaker offerings-each of which was designed to bring best-in-class performance to its price point.
Inside each low-profile, tour-grade wood enclosure are a host of unique new features that set ETX Powered Loudspeakers apart, combining intelligent technology and innovative industrial design for spectacular results across all applications. EV-engineered high-efficiency transducers and high-powered Class-D amplifiers, Signal Synchronized Transducers (SST) waveguide design and smart FIR-Drive DSP all work together to provide peerless EV sound quality and precise coverage at the highest SPLs.
- 15-inch LF SMX woofer
- 1.25-inch HF titanium compression driver
- 2000 W Class-D power amplifier with integrated FIR-Drive DSP
- 135 dB peak SPL
Frequency Range | 40 Hz - 20 kHz | Maximum SPL | 135 dB peak dB | Power Consumption | 100 - 240 V~, 50 - 60 Hz, 1.6 - 0.8 A | Power Rating | 2000 W | Frequency Response | 48 Hz - 20 kHz | Coverage (Nominal -6 dB) H | 90 ° | Coverage (Nominal -6 dB) V | 60 ° | LF Transducer | SMX2150 380 mm (15 in) | HF Transducer | DH3-B 1.25-in titanium compression driver | Crossover Frequency | 1500 Hz | Connector Type | (2) XLR/TRS combo jack and (1) XLR link output | Enclosure Material | 18-mm, 13-ply birch plywood with EVCoat | Grill | 16AWG steel with powdercoat | Suspension | (8) M10 suspension points | Height | 691 mm (27.2“) | Width | 431 mm (16.97“) | Depth | 447 mm (17.6“) | Weight Net | 27.7 kg (61.07 lbs) | Shipping Weight | 31.5 kg (69.45 lbs) |
|
Reviews
There are no reviews yet.