PRESONUS EUREKA -SINGLE CHANNEL PREAMPLIFIER COMPRESSOR and EQUA

The EUREKA Pro Recording Channel

The Eureka is a professional recording channel strip containing a discrete class A
transformer-coupled microphone preamplifier, compressor, and three-band parametric
equalizer. The microphone preamplifier features variable input impedance so that the
Eureka can be matched and "tuned" for all types of microphones and recording
applications. The Class A transformer-coupled microphone preamplifier also features
"SATURATE" which adjusts the drain current on the input FET amplifier to simulate of
the effects of tape saturation and tube "warmth“.
The Eureka's ultra fast compressor has both soft and hard knee compression as well
as a separate make up gain stage and hi-pass side chain compression to deliver hard
pumping to ultra transparent compression and everything in between. The Eureka's three-
band fully parametric EQ gives you variable Q (bandwidth) on each band as well as an
EQ pre COMP switch to put the EQ before the Compressor in the signal path. The equalizer
has overlapping frequency selection on each band for total tonal control and shaping.
The Eureka is loaded with microphone, line and instrument input so you can use it as a front
end preamplifier for recording with microphones, guitars, keyboards, synths as well as a
compressor/equalizer on a single channel during mixdown. The Eureka also has balanced send
and return jacks so that you can insert your favorite outboard processor before the compressor/
EQ to further enhance and customize your sound.
An optional 24 Bit/192kHz digital output card (AD192) is available for the Eureka to further
optimize sonic performance. The Eureka's AD192 digital output card is loaded with both SPDIF
and AES/EBU outputs, word clock I/O as well as a balanced TRS line input so that only one
output card is necessary when using two Eureka's in stereo or dual mono situations.
The Eureka gives you the sonic performance and control you need in the real-world to produce
professional quality audio that you, your customers and your fans deserve!

 Features
? Class A High Headroom Transformer Coupled Microphone Preamplifier
? Variable Microphone Input Impedance
? Variable SATURATE control (simulates tape saturation and tube warmth)
? Fully Variable Compressor with Hi-pass Side Chain
? Three Band Fully Parametric Equalizer
? EQ Pre or Post Compressor
? High Headroom Output Section
? Very Low Noise Design
? Internal Power Supply
? Transparent, wide range performance
? Optional 24-Bit/192k Digital Output Card (AD192)
  
Technical Specifications
Channels One
Dynamic Range >115dB
Headroom +22dB
Frequency Response 10Hz to 50kHz
Internal Operating Level 0dBu = 0B
Microphone Preamp
Input Impedance, XLR Input 1.3k Ohms
Input Impedance, Line Level Input 10k Ohms
Connectors Neutrik? Combo
Microphone Preamp
Gain +12dB to +52dB
Noise Floor -112dBu (+12dB gain)
EIN -127dB
THD + Noise (0% saturation)

PreSonusʼ popular Class A XMAX preamps are widely lauded for their clarity and transparency. Our tube preamps are beloved for their warm, smooth sound. With the Blue Tube DP V2 dual-path mic/instrument preamp, you get both types of high-quality sound in one unit.

Now weʼve improved on the classic unit with the BlueTube DP V2. The solid-state path now feeds PreSonusʼ top-of-the-line Class A XMAX™ mic preamplifier with 80 dB of variable gain—an upgrade from the original BlueTube DPʼs solid-state stage.

You still get all the secondary features you expect in a professional-grade preamp: 48V phantom power, an 80 Hz high-pass filter, -20 dB pad to control hot input signals, and a polarity-reverse switch. Each channel has an illuminated VU meter so you can visually monitor your input levels.

A Tube Drive control provides a wide range of sounds: when itʼs clicked off, youʼre using the solid-state preamp for quiet, transparent amplification; when itʼs engaged, your signals flow through the tube preamp, and you can achieve anything from gentle warmth to edgy distortion.

    2 input channels, each with:
        High-headroom Class A XMAX™ mic preamplifier with 80 dB gain range
        12AX7 vacuum tube gain stage
        Tube Drive tube-saturation control
        48V phantom power
        80 Hz high-pass filter
        -20 dB pad to reduce hot input levels
        Polarity-reverse switch
        Illuminated analog VU input-level meter

    Input/Output
        2 balanced combo mic/unbalanced instrument inputs
        2 balanced XLR main (L/R) line outputs
        2 unbalanced ¼” main (L/R) line outputs

    Physical
        Compact 1/2U chassis
        External 12 VDC, 1A power supply

The PRE-73 MKIII is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The in- and output is transformer balanced, using two different transformers, each one optimized for its purpose. This is the way audio components were built before integrated circuits became available.

The circuit used in the PRE-73 MKIII is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

Features  :

• Vintage Style electronics. No intergrated circuits in the signal path.

• Maximum gain in MIC mode is 80 dB, enough to handle passive ribbon mics with quiet sound sources.

• GAIN switch range 20 - 80 dB. GAIN/LINE mode switch, gain is reduced by 30 dB in LINE mode.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable 6 dB/octave two frequency high pass filter at around 40 (HP1) and 170 Hz (HP2).

• Tantalum capacitors in the signal path.

• Switchable impedance in MIC mode, 1200 or 300 Ohms, will change the tone of most mics. The input impedance in LINE mode is 10 kohm.

• Switchable phantom power and absolute phase.

• A high-impedance instrument input for any sound module, electric guitar or bass.

• A simple but effective 4-step LED output level meter.

• The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.

• Combo XLR/TRS input jack and separate output XLR and TRS jacks for flexible connections.

• Insert jack for inserting EQ´s and other units.

• Selectable 600 ohm output termination.

• The pcb is prepared for the Carnhill input transformer.

• External power supply to avoid interaction with the audio circuits and transformers.

• A solid build quality that will last many years of normal use.

The MKIII has the following new features compared to the MKII:

• Tantalum capacitors in the signal path.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable two frequency high pass filter, 6 dB/octave at 40 or 170Hz.

• The pcb is prepared for the Carnhill input transformer.

• Revised and less complicated GAIN switch with a separate switch for MIC/LINE selection.

• All GAIN settings can also be used in LINE mode .

The PRE-73 Mk2 pre-amp and the FC3 condenser microphone in one bundle. The bundle also includes Golden Age P1 Pop Filter, Proel RSM180 mic stand and Proel CHL250 5m cable.

Mic Inputs
• Frequency response at minimum gain (0dB): -0.35dB at 20Hz and –3dB at 122kHz
• Frequency response at maximum gain (60dB): –2.5dB at 20Hz and –3dB 103kHz
• Gain range: 0dB to +60dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +7.4dBu
• THD+N: 0.0009% (measured at 1kHz -20dBu input signal, at 30dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise EIN: -126dB (measured at 60dB of gain with 150Ω termination and 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -98dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 123dB (relative to max output 25dBu)
• SNR: 120dB (relative to 0dBFS (+22dBu)
• CMRR: 88dB.
• Input Impedance, variable: 600Ω, 1400Ω, 2400Ω, 6800Ω

Line Inputs
• Frequency Response at unity gain (0dB): -0.3dB at 20Hz and –3dB at 94kHz
• Gain range: -20dB to +10dB in 10dB steps, plus 0dB to +20dB continuously variable trim
• Maximum headroom: +25.4dBu
• THD+N: 0.002% (measured with +4dBu input signal, 0dB gain setting, with a 20Hz/22kHz bandpass filter)
• Noise at main output with unity gain: -91dBu (measured with a 20Hz/22kHz bandpass filter)
• SNR: 116dB (relative to max output 25dBu)
• SNR: 113dB (relative to 0dBFS +22dBu). Input Impedance: 10kΩ

Instrument Inputs
• Frequency Response at +10dB gain: -0.2dB at 20Hz and 0dB at 200kHz
• Frequency Response at +40dB gain: -3dB at 20Hz and –3dB at 38.4kHz
• Gain range: +10dB to +40dB continuously variable
• Maximum headroom: +11.5dBu
• THD+N: 0.006% (measured with –20dBu input signal, at minimum gain (+10dB), with a 20Hz/22kHz bandpass filter)
• Noise at main output with minimum gain (+10dB): -95dBu (measured with a 20Hz/22kHz bandpass filter)
• Input Impedance = >1MΩ

High Pass Filter
• Roll off = 18dB per octave 3 pole filter
• Frequency range: 16Hz to 420Hz (continuously variable, measured at the 3dB down point)

Meters
• 6 LED meter is calibrated 0dBFS = +22dBu (the maximum level which can be correctly converted by the optional internal A/D converter before overload occurs). The meter calibration points are as follows:

Meter panel calibration value in dBFS / Equivalent dBu value
0dBFS / +22dBu
-2dBFS / +20dBu
-6dBFS / +16dBu
-12dBFS / +10dBu
-18dBFS / +4dBu
-42dBFS / -20dBu



Front and rear connectivity

Analogue Channel Inputs (Inputs 1-4)
• 4 instrument 1⁄4” TS jack inputs on front panel
• 4 microphone XLR inputs on rear panel
• 4 line 1⁄4” TRS jacks on rear panel
• 4 insert return 1⁄4” TRS jacks on rear panel
• 4 ADC XLR inputs on rear panel

Analogue Audio Outputs (Outputs 1-4)
• 4 line XLR outputs on rear panel
• 4 insert send 1⁄4” TRS jacks on rear panel

Other I/O
• IEC power input connector 100Vac – 240Vac

Front Panel Indicators
• 8 output meters, 6 segment
• 4 30-60 mic gain range selection indicator
• 4 +48V phantom power indicator
• 4 Phase indicator
• 4 Insert In indicator
• 4 Filter In indicator
• 4 Input selection indicators (Mic, Line, Inst)
• 4 Z In microphone input impedance selection indicators (Low, ISA110, Med, High) Clock select indicators (44.1, 48, 88.2, 96, 176.4, 192)
• Ext clock indicators (Lock, Word clock, 256X)

Weight
5.5kg
12.2lbs

Dimensions (W x H x D)
480mm (W) x 88mm (H) x 280mm (D)
19" (W) x 3.5" (H) x 11" (D)