Content |
120W POWER AMPLIFIER This new Proel booster series has been designed to meet in a professional and flexible way the continue market evolution and demand. Such range of booster applies to an operating precise criterion to ensure to the user high performance and reliability. Main features - 8 ohm constant impedance output and constant voltage (50/70/100 V) - Further 100V output and 24Vdc output available only for the booster as for paging purposes
Microphone stands input for preamplifier stand ref. BM100A with priority function VOX - Further priority input throughout a contact - Input line signal connector - Telephone input - Low and high tone control - Main master control - PA-HF filter rear insertion - Rear ground left selector - Rear power supply selector - 24 Vdc power supply
Type: | Power Amplifier | Power: | 1x120W@8Ω/100V | Frequency Response: | 50Hz-20KHz | Inputs: | 1xXLR/RCA | Special Items: | Input emergency override, Adjustment bass, treble | Dimensions (W x H x D): | 483x88x300mm | Rack Mount: | 2U | Weight: | 10 kg | Τype: | 100V | Rack Mount: | 2U |
|
Specifications Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| Sensitivity (at 8 ohm rated output) |
1.4V
| Maximum Input Signal |
+22 dBu typical
| Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| Ventilation |
Flow-through ventilation from front to back
| Cooling |
Heat sinks and proportional-speed fan
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with the VP-2064, VP-2122, VP-2241 or VP-2421 power amplifier.
Power Source | Supplied from VP-2064, VP-2122, VP-2241 or VP-2421 | Current Consumption | 30 mA or less | Power Amplifier Link | RJ45 female connector for connecting the VX-200SP,
VX-200SZ Audio Output module, or SX-2100AO.
Twisted-pair straight cable (TIA/EIA-568A standard) | Finish | Panel: Surface-treated steel plate | Dimensions | 88 (W) × 25.8 (H) × 53.2 (D) mm | Weight | 50 g | Applicable Model | VP-2064, VP-2122, VP-2241, VP-2421 |
|
Multi-purpose, multi-function mixer/power amplifiers specifically designed for maximum versatility and cost-effective high-performance are ideal units for any PA requirement in locations such as schools and offices and other intermediate size environments. A choice of different power outputs are offered as well as functions such as paging and dual zone coverage.
Specification | |
Power Source |
AC mains 50/60Hz, or 24V DC (M4 screw terminal) |
Output |
120W |
Power Consumption |
AC operation: 158W (rated output), 66W (EN60065) 24V DC operation: 7.0A (rated output), 2.8A (EN60065) |
Frequency Response |
50 - 20,000Hz ±3dB |
Distortion |
Under 2% at 1kHz, rated power |
Input |
MIC 1: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack DIN socket (5 pins) MIC 2, 3: -60dB(*1), 600Ω, electronically-balanced, combined type of XLR-3-31 Equivalent and phone jack AUX 1(MOH): -20dB*, 10kΩ, unbalanced RCA pin jack AUX 2: -20dB(*1), 10kΩ, unbalanced, RCA pin jack AUX 3: -20dB(*1), 10kΩ, unbalanced, RCA pin jack combined type of XLR-3-31 and phone jack TEL(*2): -20dB*1, 10kΩ, electronically-balanced, M3 screw terminal |
Output |
REC: 0dB(*1), 600Ω, unbalanced, RCA pin jack LINE 1,2(*3): 0dB(*1), 600Ω, unbalanced, RCA pin jack MOH: 0dB(*1), 600Ω transformer balanced, M3 screw terminal SPEAKER SELECTOR: 2 zone, high impedance (100V line/83Ω), individual selector switch, M4 screw terminal DIRECT SPEAKER OUT: High impedance (100V line/83Ω),M4 screw terminal Low impedance (4 - 16Ω), M4 screw terminal(Both Low and High impedance terminals cannot be used at the same time.) |
Phantom Power |
ON or OFF for each MIC 1 - 3 with switch setting |
S/N ratio (Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min) Over 76dB (Master volume: max) Over 60dB (MIC 1 - 3)) Over 76dB (AUX 1 - 3) Over 90dB (TEL) Over 96dB (EMERGENCY) |
Control Input |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz TEL: No-voltage make contact input, open voltage: 24V DC, short-circuit: under 5mA, M3 screw terminal EMERGENCY (*4): No-voltage make contact input, open voltage: 24V DC, short-circuit: under 10mA, M3 screw terminal |
Control Output |
Power remote: Open collector output, withstand voltage: 35V DC, control current: under 50mA, M3 screw terminal |
Indicator |
5 point LED output level meter, Power indicator LED, Zone indicator LED, Emergency LED, TEL LED |
Priority |
EMERGENCY: Overrides other inputs TEL: Overrides other inputs except "EMERGENCY”, ON/OFF selectable with switch setting MIC 1: Overrides other inputs except "EMERGENCY & TEL”, ON/OFF selectable with switch setting |
Operating Temperature |
-10ºC - +40ºC |
Finish |
Panel: ABS resin, black, hair line Case: Steel plate, black |
Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
Weight |
12.6kg |
Accessory |
Power cord x 1, Terminal block cover x 1, Terminal block cover mounting screw x 2 |
Option |
Rack mounting bracket: MB-25B, Volume control cover: YA-920, Input transformer: IT-453A |
Note* |
(*1) 0dB = 1V (*2) Can be transformer-balanced with the addition of optional IT-453A input transformer. (*3) LINE 1 and LINE 2 outputs can be interlocked with ZONE 1 and ZONE 2 speaker selectors, respectively. (This function needs internal modification.) (*4)Operation when activated can be selected from the following: Turning ON the unit\'s power (factory-preset) or OFF. (The OFF function needs internal modification.) |
|
P-120D features 2x 200W into 4 Ohm load. This amplifier matches the needs for noiseless operation through air-cooling. It is ideally suitable in studios, small theatres, cabarets, churches, conference- and multimedia rooms etc. Multiple protection circuits care for stable operation. The amplifier is rackmountable (2 units). The optional transformer LT-101 converts the input to a balanced transformer isolated input. |
The Crown 135MA is a high value mixer-amplifier for commercial audio. It provides 8-ohm and constant-voltage outputs (70V and 100V). Typical uses are paging, background music, and music-on-hold. The 135MA provides 3 inputs (each with a volume control) and a 35W amplifier output. Other features include priority muting, voice activated muting, phantom power, and Bass and Treble controls.
Features
- 3 inputs (each with a volume control), and one 35W amplifier output channel
- Ideal for paging, background music, and music-on-hold
- Balanced Phoenix-type mic/line input, telephone output, dual RCA stereo music inputs, screw-terminal speaker outputs
- Priority muting by VOX or external switch
- Bass and Treble controls on master output
- Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
Specifications
- Minimum Guaranteed Power into 8 ohms or 70V/100V Output: 35W
- Frequency Response (at 1 watt from line out): 50Hz to 20kHz +/-1dB; 19Hz to 34kHz +0, -3dB
- Signal to Noise Ratio (ref. to rated power, master volume at minimum):
Mic: > 58 dB.
Line: > 60 dB.
Telephone: > 60 dB.
Inputs 2 or 3 (and 4 in 160MA): > 78 dB - THD+N:
|
Reviews
There are no reviews yet.