DB1A includes an MU-METAL core transformer able to reduce phase and harmonic distortion to a minimum, with noticeable improvement of the linear phase even on very long cables. The audio integrity is guaranteed by low-noise, low-consumption IC for balancing the signal, able to handle very low-impedance loads. The input section features JACK and XLR connectors […]
DB1A includes an MU-METAL core transformer able to reduce phase and harmonic distortion to a minimum, with noticeable improvement of the linear phase even on very long cables. The audio integrity is guaranteed by low-noise, low-consumption IC for balancing the signal, able to handle very low-impedance loads. The input section features JACK and XLR connectors with link possibility and a PAD of up to 30 dB that permits very high-level signal inputs to be used.
Technical Specifications
Type :
1 channel active DI
Width :
215 mm(8.465inch )
Height :
50 mm(1.969inch )
Depth :
125 mm(4.921inch )
Weight :
1 kg(2.205lb )
Rack Units :
1/2 rack unit.
Removing the two molded sides and attaching two units, with the supplied brackets, you can mount two by two DI boxes into a standard 19¿ rack.
Power Supply :
Phantom Power: +24 volts DC to +48 volts DC
External AC/DC adaptor: +9 volts DC with link
Standalone/Standby: 9 volt PP3 type battery.
Current drain :
Inputs :
Two Parallel 1/4′ jack connectors and one parallel XLR connector (unbalanced).
Input Impedance :
1M Ohm (pad at 0 dB)
47k Ohm (pad at -10/-20 dB)
44k Ohm (pad at -30 dB)
Input Levels :
+5 dBu (pad at 0 dB)
+15 dBu (pad at -10 dB)
+25 dBu (pad at -20 dB)
+35 dBu (pad at -30 dB)
Outputs :
XLR male: Pin 2 Hot / Pin 3 Cold / Pin1 Ground
Output Levels :
into 600 Ohms or greater
+3 dBu (for 0.1% THD at 50 Hz)
+5 dBu (for 0.1% THD at 1k Hz)
Connectors :
XLR male: Pin 2 Hot / Pin 3 Cold / Pin1 Ground
Channels :
1 nr.
Frequency response :
10 Hz to 100 kHz, +0dB/-1 dB
Distortion (THD) :
S/N Ratio :
Controls :
On/off, Pad -10, Pad -20, Gnd Lift, Ø inv.
Notes :
CMR > 60 dB
Phase distortion +14° at 20 Hz, -6° at 20k Hz
Weight
1.00 kg
Reviews
There are no reviews yet.
Be the first to review “PROEL DB-1A DI Box” Cancel reply
DB1A includes an MU-METAL core transformer able to reduce phase and harmonic distortion to a minimum, with noticeable improvement of the linear phase even on very long cables. The audio integrity is guaranteed by low-noise, low-consumption IC for balancing the signal, able to handle very low-impedance loads. The input section features JACK and XLR connectors with link possibility and a PAD of up to 30 dB that permits very high-level signal inputs to be used.
Technical Specifications
Type :
1 channel active DI
Width :
215 mm(8.465inch )
Height :
50 mm(1.969inch )
Depth :
125 mm(4.921inch )
Weight :
1 kg(2.205lb )
Rack Units :
1/2 rack unit.
Removing the two molded sides and attaching two units, with the supplied brackets, you can mount two by two DI boxes into a standard 19¿ rack.
Power Supply :
Phantom Power: +24 volts DC to +48 volts DC
External AC/DC adaptor: +9 volts DC with link
Standalone/Standby: 9 volt PP3 type battery.
Current drain :
Inputs :
Two Parallel 1/4' jack connectors and one parallel XLR connector (unbalanced).
Input Impedance :
1M Ohm (pad at 0 dB)
47k Ohm (pad at -10/-20 dB)
44k Ohm (pad at -30 dB)
Input Levels :
+5 dBu (pad at 0 dB)
+15 dBu (pad at -10 dB)
+25 dBu (pad at -20 dB)
+35 dBu (pad at -30 dB)
Outputs :
XLR male: Pin 2 Hot / Pin 3 Cold / Pin1 Ground
Output Levels :
into 600 Ohms or greater
+3 dBu (for 0.1% THD at 50 Hz)
+5 dBu (for 0.1% THD at 1k Hz)
Connectors :
XLR male: Pin 2 Hot / Pin 3 Cold / Pin1 Ground
Channels :
1 nr.
Frequency response :
10 Hz to 100 kHz, +0dB/-1 dB
Distortion (THD) :
S/N Ratio :
Controls :
On/off, Pad -10, Pad -20, Gnd Lift, Ø inv.
Notes :
CMR > 60 dB
Phase distortion +14° at 20 Hz, -6° at 20k Hz
Palmer PAN 03 19" DI Box 4-Channel active
Active 4-channel DI box. Each channel has a jack input with a parallel output for passing through the signal. An attenuation switch (-30 dB) allows either a line or loudspeaker signal to be connected.Active 4 x DI box, 19" format. Technical specitications identicl to the PAN-02, however, the PAN-03 is built for mains operation. All connections and switches are located on the front panel, an additional parallel XLR output is located in back. 19 inch rack-mount format, 1 rack space, 90 mm front to back.
Product type
DI Boxes
Type
active
Channels
4
Inputs
4
Input connectors
6.3 mm jack
Max. input level
+ 45 dBu
Input impedance
(@ 60 Hz) 1 M Ohm(s)
Input pad
0 / -30 dB
Outputs
4 (+ 4 parallel XLR outs)
THRU outputs/channel
1
Output connectors
6.3 mm jack , XLR
Max. output level
+ 10 dBu
Output impedance
600 Ohm(s)
Frequency response
10 - 20000 Hz
Transformer balanced
Yes
Ratio
10 : 1
Indicators
Power
Controls
attenuator , ground lift
Operating voltage
external
Cabinet material
sheet steel
Cabinet surface
Powder coated
Width
480 mm
Width
19 "
Depth
90 mm
Height
45 mm
Height
1 U
Weight
1,6 kg
User´s Manual
LD Systems LDI02
DI Box active
Active DI box in a sturdy metal housing (aluminium/steel) with protective corners, silver-blue metallic, internal battery (9 V flashes during operation) is switched off automatically when phantom power is used (LED permanently illuminated),
extremely low battery consumption. Battery: 9 V block (not included).
Product type DI Boxes
Channels 1
Inputs 2
Input connectors 6.3 mm Jack , XLR
Max. input level + 10 / + 30 dBu dBu
Input impedance 1 M Ohm(s)
Outputs 1
THRU outputs/channel 1
Output connectors XLR
Frequency response 20 - 20.000 Hz
THDIndicators Power
Controls ground lift , Power
Operating voltage +48 V phantom power , 9 V block
Cabinet material metal
Cabinet surface painted
Width 135 mm
Depth 128 mm
Height 53 mm
Weight 0,645 kg
DOD AC 275 Active Direct Box with Switchable Ground Lift and Attenuator-2nd Hand-
The AC 275 is an active, phantom powered direct box. Unlike a passive DI where the frequency response of the signal can be altered depending on the connected impedance, an active DI buffers the input signal with an amplifier. This assures that the sound source will reach the mixer balanced and noise-free.
Housed in a cast alloy chassis, the AC 275 supplies two, high impedance, unbalanced 1/4" jacks and one low impedance balanced XLR jack. It operates with battery or phantom power.
Key Features
?
Active direct box
?
Allows a hi impedance unbalanced source to directly feed a low impedance balanced input
?
Flat frequency response
?
Connects guitar pickups, microphones or electric instruments to a recording or P.A. console without audio quality loss
With added functionality and enhanced audio performance, the AR-133 has been
designed to be more affordable for musicians, studios and PA companies.
The unit includes phantom power and battery supplies as standard. Should the
phantom power from the console fail or be accidentally switched off, the AR-133
automatically switches over to the internal 9V battery providing uninterrupted use.
The unit is housed in a rugged aluminium extrusion case, with robust polyurethane
end-cheeks which give the AR-133 a very distinctive look.
Input connectors are both 1/4" jack sockets and an XLR socket, the latter meaning
that the AR-133 can be used to convert unbalanced signals to a balanced output on
XLRs throughout.
The arched case allows cables to run back underneath the unit from the end for neat
cable management.
Input attenuation is 0, -20 or -40dB, making the box suitable for instrument, line or
amplifier levels on inputs. On the output side, a ground-lift switch is provided for quick
solutions to ground-loop problems.
The AR-133 uses an enhanced version of the same audio path as the AR-116, now
regarded by many people as a reference standard. The sound quality is legendary,
particularly on acoustic and bass guitars.
Numerous applications can be satisfied by the AR-133. For example, as well as the
traditional guitar use, the AR-133 can be used with keyboards, DJ consoles, amplifier
outputs, and other electronic sources.An additional bonus is the ability to use the AR-133
as an active balancing device.
Input Section
Input Impedance 1M Ohm (pad at 0dB)
47k Ohm (pad at -20dB)
47k Ohm (pad at -40dB)
Max Input Level +9dBu (pad at 0dB)
+29dBu (pad at -20dB)
+49dBu (pad at -40dB)
Connectors Two Parallel 1/4" jack connectors and a parallel
XLR connector (unbalanced)
Jack: Tip Hot (+ve)
Sleeve Ground
XLR: Pin 2 Hot (+ve)
Pin 1 & 3 Ground
Output Section
Output Transformer Balanced
Max. Output Level +8dBu into 600 Ohms or greater
Connector XLR3-32 or equivalent
System Performance
Distortion (THD) < 0.005% at 1khz, 0dbu output
Noise < -105db unweighted, 22hz-22khz, rms*
Frequency Response 30Hz to 20kHz, +0dB/-1dB
General
Main/Standby battery 9 volt PP3 type, preferably alkaline.
Current drain on phantom - less than 7.5mA
on battery - less than 2mA.
Phantom Power +20 volts DC to +48 volts DC
Weight 650 gms, excluding batteries.
Overall Dimensions 59 mm x 124 mm x 143 mm
(2.3" x 4.9" x 5.6“)
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic music instruments such as keyboards, synthesizers, electric and electronic pianos, etc. with mixing consoles in PA-systems and in recording studios. The SM-6 is designed for applications, where a passive DI-Box does not perfom satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone input section of the mixing desk. Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are not loaded or in any other way adversely affected. The voltage ratio from input to output is 1: 1 and is always sufficient for connection with any microphone input. Input connectors are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms, transformer balanced. The output level may in certain cases overload microphone inputs - the line input section of the mixing console must then be used for connecting the SM-6. The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm max. input impedance + 6 dBu, 1,55V ouptut impedance 600 Ohm frequency response 20 ... 20000 Hz, ± 0,2 dB gain 1 : 1 THD < 1 % at 30 Hz < 0,7 % bei 40 Hz powering 9-V battery (IEC 6LF22) or phantom power 24 ... 48 V. inputs two 1/4" phone jacks , unbalanced (one being used as output to instruments amp) outputs XLR, balanced pin 1 = ground, pin 2 = hot, pin 3 = cold case aluminium die-cast weight 240 g dimensions 113 x 71 x 37 mm
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.