QSC PL-340 POWER AMPLIFIER 2x1250W RMS @4Ω, 2x2000W RMS @2Ω

1,749.00 incl. GR VAT

Available on backorder

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
Power Rating Stereo Mode: 8Ω EIA 1 kHz 1% THD – 800W 4Ω EIA 1 kHz 1% THD – 1250W 2Ω EIA 1 kHz 1% THD – 2000W Bridged Mono: 8Ω EIA 1 kHz 1% THD – 2600W 4Ω EIA 1 kHz 1% THD – 4000W Damping Factor     Not Specified By Manufacturer Input Sensitivity […]

 

Read more

Power Rating

Stereo Mode:
8Ω EIA 1 kHz 1% THD – 800W
4Ω EIA 1 kHz 1% THD – 1250W
2Ω EIA 1 kHz 1% THD – 2000W

Bridged Mono:
8Ω EIA 1 kHz 1% THD – 2600W
4Ω EIA 1 kHz 1% THD – 4000W

Damping Factor     Not Specified By Manufacturer
Input Sensitivity     26dB Setting – 3.92V
32dB Setting – 1.96V
Input Impedance     > 10kΩ balanced, or unbalanced
Gain     36.4dB
Frequency Response     20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio     -105dB
Total Harmonic Distortion (THD)     0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections     Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors     Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel     AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear)     Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators     Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution     Flow-thru air path and solid aluminum heat sinks
Power Consumption     120V 50/60Hz – 12A
230V 50Hz – 7A
Power Requirements     Not Specified By Manufacturer
Dimensions (WxHxD)     19 x 3.5 x 15.63″ (48.3 x 8.9 x 39.7cm)
Weight     33.5 lbs (15.2kg)
Specialties     Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity

Weight 10.00 kg

Reviews

There are no reviews yet.

Be the first to review “QSC PL-340 POWER AMPLIFIER 2x1250W RMS @4Ω, 2x2000W RMS @2Ω”

Your email address will not be published. Required fields are marked *

Quick Comparison

QSC PL-340 POWER AMPLIFIER 2x1250W RMS @4Ω, 2x2000W RMS @2Ω removeCrown DSI-4000 2x1200W-4Ω Power Amplifier removeELECTRO VOICE CP3000S Compact Precision Series Class-H Power Amplifier 2X1100 WATT removeDYNACORD H-2500 Power Amplifier 1950 Watts removeELECTRO VOICE TG5 High Power Amplifier, Class-H ,Switch Mode Pwr Supply, 2U 2 x 1450 W removeDYNACORD DSA-8212 2 CHAN POWER AMPLFIER 2X1800W/2Ω - 2X1200W/4Ω - 2X750W/8Ω remove
NameQSC PL-340 POWER AMPLIFIER 2x1250W RMS @4Ω, 2x2000W RMS @2Ω removeCrown DSI-4000 2x1200W-4Ω Power Amplifier removeELECTRO VOICE CP3000S Compact Precision Series Class-H Power Amplifier 2X1100 WATT removeDYNACORD H-2500 Power Amplifier 1950 Watts removeELECTRO VOICE TG5 High Power Amplifier, Class-H ,Switch Mode Pwr Supply, 2U 2 x 1450 W removeDYNACORD DSA-8212 2 CHAN POWER AMPLFIER 2X1800W/2Ω - 2X1200W/4Ω - 2X750W/8Ω remove
Image
SKU010011DSI-4000001736E009295001915E009305
Rating
Price 1,749.00 incl. GR VAT 1,688.00 incl. GR VAT1,912.00 incl. GR VAT 4,498.00 incl. GR VAT3,640.00 incl. GR VAT 1,296.00 incl. GR VAT
Stock

Available on backorder

Available on backorder

Available on backorder

Available on backorder

Available on backorder

Available on backorder

AvailabilityAvailable on backorderAvailable on backorderAvailable on backorderAvailable on backorderAvailable on backorderAvailable on backorder
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content

Power Rating

Stereo Mode:
8Ω EIA 1 kHz 1% THD - 800W
4Ω EIA 1 kHz 1% THD - 1250W
2Ω EIA 1 kHz 1% THD - 2000W


Bridged Mono:
8Ω EIA 1 kHz 1% THD - 2600W
4Ω EIA 1 kHz 1% THD - 4000W

Damping Factor     Not Specified By Manufacturer
Input Sensitivity     26dB Setting - 3.92V
32dB Setting - 1.96V
Input Impedance     > 10kΩ balanced, or unbalanced
Gain     36.4dB
Frequency Response     20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio     -105dB
Total Harmonic Distortion (THD)     0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections     Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors     Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel     AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear)     Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators     Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution     Flow-thru air path and solid aluminum heat sinks
Power Consumption     120V 50/60Hz - 12A
230V 50Hz - 7A
Power Requirements     Not Specified By Manufacturer
Dimensions (WxHxD)     19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight     33.5 lbs (15.2kg)
Specialties     Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity

Crown DSi 4000 2x1200W-4Ω Power Amplifier

The Crown? DSi 4000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 1,600W with 1% THD, 4 ohm
Stereo (per channel): 1,200W with 0.5% THD, 8 ohm Stereo (per channel):
650W with 0.5% THD, 4 ohm Bridge-Mono: 3,200W with 1% THD, 8 ohm
Bridge-Mono: 2,400W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.61V.
Sensitivity at 4 ohm rated output: 3.47V.
Sensitivity at 2 ohm rated output: 2.84V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 8.0A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave, Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB bandpass
gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Delay: Up to 50 msec total delay per channel.
Presets: 20 presets. One is ?DSP OFF.? Fifteen are factory-set for JBL Cinema
systems. Four are user-defi nable.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airflow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)
The amplifier shall be designated the Crown DSi 4000.

Electro-Voiceʼs new Precision Series Compact amplifiers offer proven Precision Series performance and reliability in a new compact, lightweight format made possible by a highly efficient Class-H design, which generates considerably less heat. The CP3000S is not only the first Precision Series amplifier to use a switch-mode power supply, but also the first switch-mode amplifier with EVʼs Precision Series sound. With up to 2x1600 watts into two ohms, and 2x1100 watts into four ohms, and only 17.96 lbs (8.15 kg it is both powerful and lightweight.

 

1U Panel w/ 8 XLRM + 8XLRF 2Amplifier Gain    32 dB
Continuous Rated Power
(1 kHz, THD 1%) 2Ω    1600 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω    1100 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω    600 Watts
Continuous Rated Power
(20-20 kHz, THD

The power amp H2500 is part of Dynacordʼs new PowerH SERIES, which marks a milestone in the design and the production of high-performance power amplifiers. The innovative 3-stage Grounded Bridge Class H Topology with "floating” switching power supply unit offers very high and stable output with extreme high efficiency on an extremely high performance level at minimum weight. PowerH amps are ideal for driving professional touring, high-end Concert-Sound and Pro-Sound applications. Next to classical protections, this new design employs the multi-stage ATP system (Advanced Thermal Protection) for the first time, which in most cases prevents the power amplifier from switching off when the temperature exceeds a critical level. The newly designed MCS system (Mains Current Supervision) prevents power amplifier breakdown caused by the activation of the automatic circuit breaker. For this, among other things, the MCS system uses the highly precise measurement of the RMS value ofthe actual mains current consumption. Information about the status of the power amplifier and its internal protections is provided on a LC-display. By utilizing the optionally available remote control module that is compatible with IRIS-Net™, this power amplifier additionally offers comprehensive remote monitoring and remote control functions plus a universal 2-channel digital audio controller (DSP) including highly precise FIR-filtering and digital speaker protection algorithms. Datasheets / ManualsManual (5.50MB)

Load Impedance 2 O, 4 O, 8 O Maximum Midband, Output Power, 1 kHz, THD=1% 2 O - 1900 W, 4 O - 1450 W, 8 O - 850 W Rated Output Power, 20 Hz ... 20 kHz, THD 400 Slew Rate 30 V/µs Signal to Noise Ratio Amplifier, A-weighted, 32 dB constant gain 109 dB Output Noise , A-weighted

Amplifier Gain    41.5 dB, 35 dB, 32 dB (switchable)
CAN Bus Interface    Optional with RCM-26
Continuous Rated Power
(1 kHz, THD 1%) 2Ω    2000 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω    1450 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω    850 Watts
Continuous Rated Power
(20-20 kHz, THD


Solid DYNACORD technology for fixed installations at very competitive prices.
DSA power amplifiers offer a very high, stable output with high efficiency at a high performance level and are therefore the ideal choice for typical fixed installation applications. The connectivity consequently provides Phoenix type in/outs, the input level controls are located on the rear panel, also a switchable high-pass filter (50 Hz, 18 dB/oct) and a Ground Lift switch.
The POWER REMOTE connector makes the task of remote controlling the power amplifier as well as switching it on and off simple. For further remote-supervision and –control possibilities and integration into IRIS-Net networks, an optional remote control module (RCM-810) is available.

acrobat_reader_logo.

Weight10.00 kg9.00 kg8.15 kg14.20 kg14.20 kg17.70 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 10.00 kg
Weight 9.00 kg
Weight 8.15 kg
Weight 14.20 kg
Weight 14.20 kg
Weight 17.70 kg