Active Reamp® with two outputs 100% discrete class-A signal path Transformer isolated to eliminate noise Variable ‘set & forget’ level control The Radial X-Amp is an active Reamper™ that allows the engineer to play a pre-recorded track back through guitar amplifiers and pedals. This opens the door to explore new musical sounds and spur on […]
The Radial X-Amp is an active Reamper™ that allows the engineer to play a pre-recorded track back through guitar amplifiers and pedals. This opens the door to explore new musical sounds and spur on the creative process so that your recording stands out.
Using the X-Amp is easy: start by recording a dry track using a high quality direct box like the Radial J48. Send the new track from your recorder via the X-Amp to your guitar amps, effect pedals or combinations thereof. Once the basic track has been recorded, replacing or adding tracks can be done well after the session player has gone home. This eliminates tiresome repetition and assures a fresh vibrant performance on the final recording. Furthermore, by driving two amps at the same time, new sounds and textures can be created while allowing you to make artistic decisions as the recording progresses.
Following the critically acclaimed Radial JD7 Injector, the X-Amp employs a unique class-A circuit design that has been optimized for use with guitars. Features include balanced line level input with LED peak indicator and level control, class-A circuit topology for optimal reach and frequency response, a transformer isolated output to eliminate hum and buzz caused by ground loops, a 180º polarity reverse switch to bring both amps into phase, and a dual ground lift switch for noise-free operation.
As with all Radial products, the X-Amp is built like a tank to provide years of trouble-free performance. An internal I-beam skeleton provides maximum protection against external stress which could cause solder points to fail. This is supplemented with an innovative bookend design that creates a protective zone around the switches, potentiometer and connectors. A full bottom no-slip pad performs double duty by keeping the X-Amp from sliding around when placed on a vibrating amplifier while also providing electrical and mechanical isolation. Reamping works equally well on bass, keyboards, drums and voice. Once you start Reamping, you will never record any other way.
The Radial X-Amp… the active Reamp® for professional recording engineers.
Weight
1.80 kg
Reviews
There are no reviews yet.
Be the first to review “RADIAL X-AMP Active Re-Amplifier” Cancel reply
Professional and multi-purpose direct injection box for stage and studio applications
Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers
Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer
Internal battery automatically shuts off when phantom power is applied
Allows direct connection to speaker outputs with up to 3,000 Watts
Content
Active Reamp® with two outputs
100% discrete class-A signal path
Transformer isolated to eliminate noise
Variable 'set & forget' level control
The Radial X-Amp is an active Reamper™ that allows the engineer to play a pre-recorded track back through guitar amplifiers and pedals. This opens the door to explore new musical sounds and spur on the creative process so that your recording stands out.
Using the X-Amp is easy: start by recording a dry track using a high quality direct box like the Radial J48. Send the new track from your recorder via the X-Amp to your guitar amps, effect pedals or combinations thereof. Once the basic track has been recorded, replacing or adding tracks can be done well after the session player has gone home. This eliminates tiresome repetition and assures a fresh vibrant performance on the final recording. Furthermore, by driving two amps at the same time, new sounds and textures can be created while allowing you to make artistic decisions as the recording progresses.
Following the critically acclaimed Radial JD7 Injector, the X-Amp employs a unique class-A circuit design that has been optimized for use with guitars. Features include balanced line level input with LED peak indicator and level control, class-A circuit topology for optimal reach and frequency response, a transformer isolated output to eliminate hum and buzz caused by ground loops, a 180º polarity reverse switch to bring both amps into phase, and a dual ground lift switch for noise-free operation.
As with all Radial products, the X-Amp is built like a tank to provide years of trouble-free performance. An internal I-beam skeleton provides maximum protection against external stress which could cause solder points to fail. This is supplemented with an innovative bookend design that creates a protective zone around the switches, potentiometer and connectors. A full bottom no-slip pad performs double duty by keeping the X-Amp from sliding around when placed on a vibrating amplifier while also providing electrical and mechanical isolation. Reamping works equally well on bass, keyboards, drums and voice. Once you start Reamping, you will never record any other way.
The Radial X-Amp… the active Reamp® for professional recording engineers.
Phantom or battery powered in a rugged steel chassis, with separate Speaker Level input connector
The ARX DI-PLUS represents another major step forward in active direct boxes. Packaged in a single channel stand-alone format, the DI-PLUS represents a fresh look at active D.I. concepts. Precision engineered Ultra quiet, ultra clean circuitry delivers maximum headroom whatever the signal. Premium grade components, plus an all-steel chassis gives excellent hum and noise specifications and superb audio quality in a tough, roadworthy package. Level control The DI-PLUS features a Normal gain high impedance unbalanced input on the front panel, running to a balanced XLR output on the rear. There is also a separate -40dB Speaker Level input for signal coming from the External (auxiliary) speaker output of an amplifier. A a global Pad switch drops both the normal input and the speaker input by a further 20dB, making it suitable for all applications, from the softest keyboard to the hottest broadcast levels.
Battery compartment The revolutionary simple 'clamshell' action of the DI-PLUS battery compartment makes battery changing extremely easy, even on the darkest stages. A 9v alkaline battery snaps into a PCB mounted battery holder for fast, secure location. No fragile battery clip leads to break, no tools required, no screws to lose. Production crew heaven!
Automatic Phantom switching The DI-PLUS will automatically switch itself to the console's own Phantom Power, if available, and an LED will indicate this mode. Turn the Phantom Power off and it will instantly revert back to battery mode. Rugged all-steel case A lot of direct boxes are fitted into brittle cast alloy cases. Not this one! The tough all-steel inner and outer chassis of the DI-PLUS provide excellent RF/EMF shielding while making it a sturdy, heavy duty unit that is hard to dislodge, and hard to leave behind.
Rear panel showing XLR connector, ground lift switch, and captive screw for opening up the unit for battery changing
Whether you're a Studio or Live Sound engineer, installation contractor, or broadcast engineer, you want all the dynamics and clarity of the original sound source transferred to the mixing console. The ARX DI-PLUS provides a rugged, no-compromise solution to all direct injection and signal balancing requirements.
T E C H N I C A L S P E C I F I C A T I O N S: Max Input Level +13 dB Phantom powered +6 dB Battery powered Input Impedance 1 Meg Ohm Max Output Level +17 dB 10K Ohm load Phantom powered +12 dB 10K Ohm load Battery powered +11 dB 600 Ohm load Phantom powered +12 dB 600 Ohm load Battery powered Output Impedance 680 Ohms Balanced Output Signal to Noise -100 dB unweighted -104 dB A weighted Dynamic Range 117 dB 10K Ohm load Phantom powered 112 dB 10K Ohm load Battery powered 111 dB 600 Ohm load Phantom powered 107.5 dB 600 Ohm load Battery powered Distortion 100 Hz .0027%, 1KHz .0028%, 10KHz .0037% Frequency Response 20Hz to 20KHz, ± 0.2 dB Gain through Unit: 6dB (Normal input, Pad switch out) Pad Switch: -20 dB attenuation Speaker Input -40 dB attenuation, equivalent to 100:1 decrease in input level -60 dB attenuation available with Pad switch Input Connectors Insulated jacks (!!!Note that the Input connector switches the unit on when a plug is inserted. Remove plug when storing to avoid battery drain!!!) Output Connector 3 pin XLR. Wired Pin 1 Ground, Pin 2 + Hot, Pin 3 - Cold. With Audio Ground (Pin 1) lift switch Construction All-steel chassis, fibreglass PCB Battery Access Twist connector opens chassis, snap-in battery holder inside. No tools required
Product Features:
Professional and multi-purpose direct injection box for stage and studio applications
Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers
Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer
Internal battery automatically shuts off when phantom power is applied
Allows direct connection to speaker outputs with up to 3,000 Watts
Switchable input attenuation allows input levels of up to +50 dB
Ground Lift switch eliminates typical ground loop problems
¼" TRS and gold-plated XLR connectors
Ultra-rugged, road-suitable aluminum case
Stackable oversized rubber corners
High-quality components and exceptionally rugged construction ensure long life and durability
Conceived and designed by BEHRINGER Germany
With the DI100, you can rest assured that your sound source will reach the console balanced and noise-free. BEHRINGER's take on the all-important active DI box gives you functionality, durability and incredible sound at a remarkable price.
Be Direct
Plug into the DI100's balanced 1/4" TRS or XLR input, then send a signal to your console via the balanced XLR output. You can even plug your guitar or bass amp's speaker output into the DI100, which can handle ratings of up to 3,000 Watts and still deliver a perfect signal. It also features a 1/4" LINK jack to send your signal to an on-stage amplifier. The DI100 also has a switchable attenuation pad, allowing input levels of up to +50 dB. There is also a ground lift switch to eliminate noise associated with ground loops. The DI100 also features BEHRINGER's renowned OT-1 output transformer.
Superior Sound, Incredible Value
DI boxes are an essential part of any stage or studio, and the DI100 delivers the exceptional sound you expect, wrapped up in a rugged, road-proof aluminum case with stackable rubber corners.
At dbx, when we do something, we do it right. So when we decided to create our new direct injection boxes, we didnʼt settle for the same old tired approach to direct box design. With our dbx name on the line, how could we? One look at our new dB10 Passive and dB12 Active direct boxes will tell you that these are clearly different. With their bullet-proof construction, and extraordinary audio performance to rival their looks, finally thereʼs a direct box worthy of the dbx name.
Utilizing custom dbx mu-metal-shielded audio transformers, high-quality Neutrik® connectors, and low-noise circuitry preserves the sonic integrity and true characteristics of the signal source. Both boxes include a pad switch that accomodates instrument, line and even speaker level signals. Take even more control of your sound by utilizing the polarity invert switch to set the phase relationship between the direct and mic'd sound.
As a professional, you donʼt have time for interference, so weʼve included a ground lift switch to solve potential hum and buzz problems due to ground loops. And between the combined shielding of the cast metal chassis and the custom-wound transformer, you can be doubly assured of a clean signal free from interference. All of this sits atop a solid, stable footprint, that will keep the box from being dragged around the stage, and the unique contoured underside allows secure stacking of multiple units.
So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx dB10 dB12 is for you.
Thru Output: 1 parallel connection from input jack
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Main Output: 1 line level
Connector: XLR male jack
Type: Balanced
Impedance: 150 Ohm typical
Max Output Level: 0dBu
PERFORMANCE
Transformer: Custom dbx mu-metal-shielded
Frequency Response: 20Hz to 20kHz, +/-2.5dB
Noise:
THD:
GENERAL
Dimensions: 5.82" L X 5.44" W X 2.20" H (148 x 138 x 56mm)
Weight: 1.4 lbs / 0.65 kg
Note: Specifications subject to change without notice.
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic music instruments such as keyboards, synthesizers, electric and electronic pianos, etc. with mixing consoles in PA-systems and in recording studios. The SM-6 is designed for applications, where a passive DI-Box does not perfom satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone input section of the mixing desk. Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are not loaded or in any other way adversely affected. The voltage ratio from input to output is 1: 1 and is always sufficient for connection with any microphone input. Input connectors are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms, transformer balanced. The output level may in certain cases overload microphone inputs - the line input section of the mixing console must then be used for connecting the SM-6. The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm max. input impedance + 6 dBu, 1,55V ouptut impedance 600 Ohm frequency response 20 ... 20000 Hz, ± 0,2 dB gain 1 : 1 THD < 1 % at 30 Hz < 0,7 % bei 40 Hz powering 9-V battery (IEC 6LF22) or phantom power 24 ... 48 V. inputs two 1/4" phone jacks , unbalanced (one being used as output to instruments amp) outputs XLR, balanced pin 1 = ground, pin 2 = hot, pin 3 = cold case aluminium die-cast weight 240 g dimensions 113 x 71 x 37 mm
1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal 1 low-impedance output (XLR) Gray housing
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.