Content |
DPS 3000 is a 2 channel power amplifier that can handle exceptionally high power ratings in a compact and lightweight 2 rack units space.
Thanks to the class HD technology, this amplifier delivers up to 2 x 1700 W RMS @ 2 Ohm (3400 W RMS bridged @ 4 Ohm), weighting just 14 kg.
It comes with a ʽPFCʼ (ʽPower factor correctionʼ) switched mode power supply which ensures that a predominantly
resistive load is presented to the mains power supply; this also leads to an improved amplifier performance at high output levels. Thanks to its high efficiency heat sinks and variable speed DC fans, the DPS 3000 can withstand the hardest heat conditions ensuring great reliability.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 2Ω: | 2 x 1700 Watt rms | | Power output stereo 4Ω: | 2 x 1200 Watt rms | | Power output stereo 8Ω: | 2 x 800 Watt rms | | Power output bridged 4Ω: | 3400 Watt rms | | Power output bridged 8Ω: | 2400 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | 108 dB | | Damping factor: | > 1000 | | Slew rate: | 55 V/μS | |
INPUT SECTION |
---|
Input connector: | xlr | | Input sensitivity: | 1.4 dBm/V RMS | |
OUTPUT SECTION |
---|
Output connector: | Speakon | |
SYSTEM PARAMETERS |
---|
Cooling: | Temperature-controlled fan | | Protections: | Temp., DC, RFI, short-circuit | | Voltage gain: | 32 – 26 dB | | Amplifier class: | HD | |
POWER REQUIREMENT |
---|
Operating voltage: | 90 ÷ 245 V (50 / 60 Hz) V ~ Hz | | Power Consumption: | SMPS W | | Power factor (cos φ): | 0.95 from 200 W to full power | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88/3.4 mm/inch | | Width: | 482/18,9 mm/inch | | Depth: | 420/16.5 mm/inch | | Net Weight: | 14/30.8 Kg/Lbs |
|
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 800W
4Ω EIA 1 kHz 1% THD - 1250W
2Ω EIA 1 kHz 1% THD - 2000W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 2600W
4Ω EIA 1 kHz 1% THD - 4000W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 3.92V
32dB Setting - 1.96V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 36.4dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -105dB
Total Harmonic Distortion (THD) 0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 12A
230V 50Hz - 7A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
Number of Channels: 2 Output Power: (per channel) 8 ohms 625W 4 ohms 1150W 2 ohms 2100w Output Power: (bridged) 8 ohms 2300W 4 ohms 4200w THD%: (@1dB below max output) @ 1kHz 20Hz to 20kHz Gain / Sensitivity: Gain 32/36dB Sensitivity (for max power) +7.5/3.5dBu (1.8/1.2V) Frequency Response: 20Hz to 20kHz (+ 0/- 0.5dB) Power Consumption: Nominal @ 240v into 4 ohms 2.8A Nominal @ 120v into 4 ohms 5.6A Dimensions: (2U) (mm) Amplifier 88(h) x 482(w) x 460(d) Single Box (UK shipping) 230 x 580 x 560 Double Box (outside UK) 250 x 610 x 600 Weight: Amplifier 20.4kg Boxed (shipping weight) 22.2kg User's Manual
|
Number of Channels: 2 Output Power: (per channel) 8 ohms 700W 4 ohms 1350W 2 ohms 2400W Output Power: (bridged) 8 ohms 2700W 4 ohms 4800W THD%: (@1dB below max output) @ 1kHz 20Hz to 20kHz Gain / Sensitivity: Gain 26/32/33dB Sensitivity (for max power) +13/7/6dBu (3.5/1.7/1.5V) Frequency Response: 20Hz to 20kHz (+/- 0.3dB) Power Consumption: Nominal @ 240v into 4 ohms 3.0A Nominal @ 120v into 4 ohms 6.0A Dimensions: (2U) (mm) Amplifier 88(h) x 482(w) x 428(d) Single Box (UK shipping) 230 x 580 x 560 Double Box (outside UK) 250 x 610 x 600 Weight: Amplifier 10.2kg Boxed (shipping weight) 11.9kg User's Manual
|
Product Highlights
- 1000W per Channel at 8 Ohms
- Efficient Class-D Amplifier
- Custom LSI Chip with PLL Technology
- Digital Routing of Inputs & Outputs
- XLR, 1/4“, SpeakON & Binding Post
- PEQ, Crossover, Filters, Delay
- D-Contour Multi-Band Dynamic Processing
|
Reviews
There are no reviews yet.