Content |
Features Soft-start limiter 3 modes: stereo, parallel, mono-bridged High-performance cooling fans with variable speed Active diplexer with adjustable frequency range (25 Hz - 150 Hz) Processing switch for equalisation of audio signals Subwoofer/low-cut switch for direct control of subwoofer/Satellites Transient pulse protected Special switch-mode power supply Overload and short circuit protection Thermal protective system Separate amplifier circuits for channels A and B Outputs: PA pro speaker cable, 6.3 mm Jacks Inputs: XLR, 6.3 mm Jacks Technical Data 1400 W PRO PA amplifier Output capacity: 2x 700 W at 8 ohm, 2x 950 W at 4 Ohm, 1x 1400 W at 8 Ohm (mono-bridged) Frequency range: 20 Hz - 20 kHz Dimensions: 483 x 88 x 490 mm Weight: 13.0 kg
| Crown XTi2002 Specifications:
* Output Power 2 ohms Stereo (per ch): 1000W
* Output Power 4 ohms Stereo (per ch): 800W
* Output Power 8 ohms Stereo (per ch): 475W
* Output Power 8 ohms Bridged-Mono: 1600W
* Output Power 4 ohms Bridged-Mono: 2000W
* Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
* Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB
* Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted)
* Total Harmonic Distortion (THD):
* Damping Factor 20 Hz to 1 kHz: > 500
* Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db
* Input Impedance (nominal): 20k ohms balanced, 10k ohms unbalanced
* Maximum Input Signal: +22 dBu typical
* Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing)
* Level Control: Two front-panel rotary level controls, one for each channel
* Power Switch Control: On/Off switch applies AC power to the amplifier
* Sel/Prev/Next Buttons Controls: Three buttons near the LCD screen that are used to access menu items and front panel lockout
* LCD Screen: Backlit liquid crystal display that shows preset and processing status
* Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
* –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.
* –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip.
* Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
* Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
* Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
* Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
* Input Connectors: XLR, one per channel
* Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
* Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
* HiQnet™ USB Connector: Type B, connects to HiQnet™ network.
* Chassis: Steel
* Front Panel: Cast-aluminum
* Cooling: Proportional speed fan with front-to-rear airflow.
* Dimensions: 19" (W) x 3.5" (H) x 12.25" (D)
* Net Weight: 18.5 lbs (8.4kg)
* Shipping Weight: 21.5 lbs (9.8kg) | The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Type
PA Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms)
2 x 800 W
Rated ouput power (1kHz @ 4 Ohms)
2 x 650 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 450 W
Rated ouput power (1kHz @ 4 Ohms, bridged)
1600 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
1300 W
Output circuitry
Class H
Frequency response
20 - 20000 Hz
THD
< 0.1 %
Signal-to-noise ratio
106 dB
Damping factor
> 400
Crosstalk
>80 dB
Gain
39 dB
Input sensitivity
0.775 V
Protection circuits
clip limiter , DC protection , short circuit , thermal overload
Controls
2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
level , Limit , Power , Protect (protection circuit engaged) , Signal
Loudspeaker outputs
2
Speaker output connections
Speakon compatible , Terminal posts
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
Weight
15,9 kg
Features
Volex mains socket |
XR Series - Intelligent Power New Horizons.
A lightweight with enormous power output. Combined with digital signal processing. That's what we call flexibility! Locally controlled or completely networked. No matter what the requirements are. The integrated powerful digital signal processor (DSP) and controller allows for a troublefree and easy adjustment to any acoustical environment. Wear-free digital potentiometers, sequential remote power on, alive contacts for easy supervision, computer controlled monitoring - its enless list of useful feature make it the right choice for any installation. XR - the new definition of Intelligent Power
High Tech SMT Design Digital Signal Processor Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon High-End Switched Power Supply with Power Factor Correction (not XR4000) LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed low noise fans Digital wear-free Volume Controls (can be operated manually) Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Paging Input Monitor Output SXL Dataport Perfect Weight-to-Power ratio 3 Years Warranty
Technical Data: Class: H Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.02% Signal-to-Noise Ratio: < -106 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 750 to 1200 @ 4 Ohm Cooling: 4 Fans (temp. reg. variable speed) Weight: 8 to 10 kg (18 to 22 lbs) Dimensions: 2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“)
| Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 1250 W, 4 Ω - 900 W, 8 Ω - 550 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 2450 W, 4 Ω - 1400 W, 8 Ω - 700 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 2800 W, 8 Ω - 1800 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +5.1 dBu (1.39 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class H Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 16.3 kg (35.9 lbs) | VLP Series Power Amplifier
Output Power:
750W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
500W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
(Bridge Mode, Mono)
1500W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 300
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift / Limiter
Dimensions (LxWxH): 14" x 19" x 3.5" / 360 x 482 x 88mm 2-rack mount spaces
Weight: 42 lbs. / 19 Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift; Limiter |
Reviews
There are no reviews yet.