RME MICSTASY Preamp / Converter A/D

Micstasy is an 8-Channel hi-end mic/line preamp and AD-converter combining typical RME features with a number of previously unseen features. It can be used analog (Mic/Line In to Line Out) and digital (Mic/Line In to Digital Out), with both signal paths operating simultaneously. Special highlight: the device is fully remote-controllable via MIDI (also MIDI over MADI).

The Micstasy's innovative concept allows for amplification and digitization of ALL analog signal sources. Be it high-level stage signals, typical studio signals, lower level and high-impedance instruments, or dynamic, condenser or ribbon microphones: Micstasy understands them all - in a way that is simply thrilling.

The signals amplified by the Micstasy are available at the analog outputs for passing them on, making an expensive splitter box on stage obsolete. All functions can be remote controlled via MIDI and MIDI over MADI, allowing the device to be placed near the microphones, ensuring highest sound quality. Adding the optional MADI Card results in even more options. The I64 MADI Card provides serial pass-through capability from one Micstasy to the next (up to 8). All up to 64 audio signals are then available at the last device on one single line.

The PRE-73 MKIII is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The in- and output is transformer balanced, using two different transformers, each one optimized for its purpose. This is the way audio components were built before integrated circuits became available.

The circuit used in the PRE-73 MKIII is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

Features  :

• Vintage Style electronics. No intergrated circuits in the signal path.

• Maximum gain in MIC mode is 80 dB, enough to handle passive ribbon mics with quiet sound sources.

• GAIN switch range 20 - 80 dB. GAIN/LINE mode switch, gain is reduced by 30 dB in LINE mode.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable 6 dB/octave two frequency high pass filter at around 40 (HP1) and 170 Hz (HP2).

• Tantalum capacitors in the signal path.

• Switchable impedance in MIC mode, 1200 or 300 Ohms, will change the tone of most mics. The input impedance in LINE mode is 10 kohm.

• Switchable phantom power and absolute phase.

• A high-impedance instrument input for any sound module, electric guitar or bass.

• A simple but effective 4-step LED output level meter.

• The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.

• Combo XLR/TRS input jack and separate output XLR and TRS jacks for flexible connections.

• Insert jack for inserting EQ´s and other units.

• Selectable 600 ohm output termination.

• The pcb is prepared for the Carnhill input transformer.

• External power supply to avoid interaction with the audio circuits and transformers.

• A solid build quality that will last many years of normal use.

The MKIII has the following new features compared to the MKII:

• Tantalum capacitors in the signal path.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable two frequency high pass filter, 6 dB/octave at 40 or 170Hz.

• The pcb is prepared for the Carnhill input transformer.

• Revised and less complicated GAIN switch with a separate switch for MIC/LINE selection.

• All GAIN settings can also be used in LINE mode .

Designed for high-definition field production environments, the studio-quality MP-1 is an ideal line-driver for critical radio, television, and film applications.

The MP-1 is extremely durable and easy to use. With rugged mechanical and electrical construction and high-quality components it will provide years of superb audio performance under the most punishing field conditions.

• Superb audio specifications
• 66 dB of gain, in eleven discrete steps
• Transformer-balanced input and output
• Phantom power - 48 volt or 12 volt
• High pass filter @  80 Hz or 160 Hz, 6 dB/octave
• Limiter makes unit virtually "unclippable“
• High current line output drive
• Excellent immunity to RF interference.
• Battery power (two x AA)
• Durable mechanical construction

The PreSonus HP60 is the most flexible and advanced headphone amplifier system available for professional and project recording studios as well as live sound in-ear monitoring systems. Loaded with six independent,
loud and clear headphone amplifiers, the HP60 features dual stereo inputs as well as external input, for each
channel allowing you to mix between three stereo audio streams (mix A, mix B, and external input). Stereo output is also available on each channel to send line level headphone channel mixes to additional headphone amplifiers or monitor systems. Each channel features headphone level, mix control between A and B inputs, external input volume, mute and mono. The HP60 also features talkback via external XLR microphone input. Common set up of the HP60 in a recording session is to send the main control room mix to input A. Send the click track to input B. Send the each band member direct recording input to each channelʼs external input (more me). This will allow each band member to create a mix between the main mix, the click track and themselves. The HP60 is the ultimate headphone amplification system delivering loud and clear headphone mixes for real-world recording situations.

Features:
-Six independent ultra low noise, high output headphone amplifiers (150 mW per channel)
-Two sets of stereo inputs (A and B) with balanced TRS connectors
-Stereo external input point on each channel for "more me” with trim control
-Mix control between inputs A and B
-Talkback with external XLR microphone with control
-Direct stereo line output on each channel

At PreSonus, weʼve been designing preamps for a long time, and we always focus on audio quality first. So when we decided to upgrade our popular TubePre V2, we focused on improving an already high-quality sound—without jacking up the price. Like the originalTubePre, the new version is a fully professional tube preamp, with a dual-servo (no capacitors) gain stage that lets you boost the program signal to smoking hot levels without significantly increasing the background noise. Discrete components and high-voltage operation offer dynamic range and detail not found in other single-channel tube preamps in its class.

Housed in a rugged case, the TubePre V2 rear panel sports separate unbalanced, ¼” instrument and balanced, XLR mic inputs and unbalanced ¼” and balanced XLR line outputs. Weʼve included all of the extras you need for professional operation including a high-pass filter, phantom power for condenser mics, polarity reverse switch, and a backlit VU meter.