| Content |
The OctaMic II provides 8-Channel 192 kHz / 24 bit AD conversion with eight hi-class microphone and line pre-amplification channels, featuring a combination of sophisticated components and approved RME technology.
Lowest distortion, excellent signal to noise ratio and perfectly linear frequency response transmit and amplify the microphone signals truly unchanged.
The OctaMic II includes some significant enhancements compared to the OctaMic:
The balanced TRS inputs of the Neutrik Combo XLR jacks are phantom power-free and can be operated as real line inputs too. The improved design of the input circuits allows for a maximum input level of +21 dBu with a convenient gain range from 6 dB up to 60 dB.
Improved signal to noise ratio (SNR) ADC 107.5 dB
Improved THD, especially at higher gains
Optimised heat dissipation by a new and larger housing with improved convection
Internal wide range power supply with line filter, insensitive to voltage fluctuations
Super-stable, short circuit proof 48 V phantom power
Features
OctaMic II offers 8 balanced XLR mic / line inputs via Neutrik XLR/TRS combo jacks. Each channel contains switches for 48V phantom power, a low cut filter and phase reversal. Amplification can be set between 6 and 60 dB. LEDs for signal, clip, and activated phantom power give a complete overview on the unit's status. When the special Clip Hold mode is activated, any detected clip-state will cause the corresponding LED to flash once per second. With this, the user gets a long-term peak detection, and no longer needs to constantly watch the LEDs. At the same time momentary overloads are still displayed correctly.
Frontside switches include power on/off and output level, for a choice of -10 dBV, +4 dBu or Hi Gain (+19 dBu) as reference level. This unusual feature offers two advantages. First, the reference level can be easily switched to match any of RME's current interface devices, from HDSP 9632 through Multiface up to the renowned ADI-8 series converters. Second, the Signal to Noise ratio is optimized, and the Clip-LED will exactly match the ones of the ADI-8 (2 dB below 0 dBFS).
The balanced line level output signal is available at the back of the unit via 8 stereo TRS jacks. The specially developed, internal hi-performance switch mode power supply lets the OctaMic II operate in the range of 100V to 240V AC. It is short-circuit-proof, has an integrated line-filter, is fully regulated against voltage fluctuations, and suppresses mains interference.
Top
AD-Conversion
The 8-Channel AD-conversion of the OctaMic II operates at up to 192 kHz. The digitized signal is available simultaneously at the double ADAT output (S/MUX, up to 96 kHz), and at a DB-25 connector (4 AES/EBU outputs, up to 192 kHz). The digital part can be clocked internally (master) and externally via word clock, AES/EBU and SPDIF.
RME's outstanding SteadyClock(TM) ensures perfect AD-conversion, as jitter on the external sync-sources is nearly completely removed. All settings are done via DIP-switches on the back of the OctaMic II. Analog outputs and both digital outputs operate fully simultaneously. The choice of reference level affects the analog outputs only, the signal/clip indication and the AD-conversion will react only to the Gain-pots.
Top
Tech Specs
8 balanced XLR/TRS mic/line inputs
54 dB gain range
Input impedance: XLR 2 kOhm, TRS 5 kOhm
Analog input level: from -40 dBu up to +21 dBu
Maximum output level: +21 dBu
Output impedance: 75 Ohm
Output level switchable Hi Gain / +4 dBu / -10 dBV
Signal to noise ratio (SNR): 129 dB EIN @ 150 Ohm
THD:
Large frequency range (200 kHz) with special EMI input filtering
Frequency response -0.5 dB: 5 Hz - 200 kHz
Hi-pass filter: 80 Hz, 18 dB/oct.
Line Out: 1/4" TRS (6.3 mm stereo jack), servo-balanced
Phantom power: +48 Volt switchable per channel
Internal wide range switching power supply 100-240 Volt AC
Unbeatable price/performance ratio!
AD conversion
SNR: >110 dB(A)
Supported sample rates: 28 kHz - 200 kHz
THD:
Sync Sources: AES/EBU (also SPDIF coaxial), wordclock, internal
SteadyClock(TM) ensures best sound quality even with jittery external clocks
Top
Accessories
Digital breakout cable Pro, AES/EBU, D-sub25 to 4x XLR-3 female + 4x XLR-3 male, 1m/3m/6m (ALVA Audio)
Digital D-sub cable, AES/EBU, D-sub25 male to D-Sub25 male, 1m/3m/6m (ALVA Audio)
Optical ADAT Toslink cable 1m/2m/3m/5m/10m (ALVA Audio)
Word Clock cable, 1 x BNC male to 1 x BNC male, 1m/5m/10m (ALVA Audio)
Top
Add-On
BOB-32 Universal Breakout Box with 2 x 8 XLR to 2 D-sub connectors (supports TASCAM and YAMAHA format), flip-frame case
|
The CPR12 is an easy to use, flexible and multifunctional 10 channel pre-amplifier. Six of these input channels are selectable between Mic / Line level and equipped with a 3 band tone control. The first two can be switched to priority and phantom power. The other four channels are direct line inputs. Every input channel has its own gain and fader volume control with PFL button which makes it possible to pre-listen each input or output channel with the built-in pre-listening speaker, and can be routed to one or both output channels. This makes the CPR12 a full two-zone system. Other present features are a priority input, a recording output, separate sub-out channels and the 24 V DC emergency power connection. This last feature makes it possible to power the CPR12 with emergency power when the main power is shut down. In this case, the priority input will automatically mute all input signals, and a evacuation message will be announced. The steel 19" housing has a height of 2 HE. ![]()
- 10 audio input sources
- 6 Mic / Line inputs with 3 band EQ
- 4 Direct Line Inputs
- Fader volume control
- Two output zones
- Built-in pre-listening speaker
- Priority input for emergency situations
- + 15 V DC Phantom power
- Works on 24 V DC emergency power
Specifications
- Model Name / Type: CPR12 / 10 channel 2 zone pre-amplifier
- THD+N:
- Signal/Noise: > 90 dB
- Frequency Response: 20 Hz - 20 kHz
- Phantom Power: + 15 V DC
- Emergency Power: + 24 V DC
- Power Supply: 100 - 240 V AC / 50 - 60 Hz
- Dimensions (W x H x D): 420 x 88 x 320 mm
|
The PRE-73 Mk2 pre-amp and the FC3 condenser microphone in one bundle. The bundle also includes Golden Age P1 Pop Filter, Proel RSM180 mic stand and Proel CHL250 5m cable. |
The PRE-73 MKIII is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The in- and output is transformer balanced, using two different transformers, each one optimized for its purpose. This is the way audio components were built before integrated circuits became available.
The circuit used in the PRE-73 MKIII is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
Features :
-
Vintage Style electronics. No intergrated circuits in the signal path.
-
Maximum gain in MIC mode is 80 dB, enough to handle passive ribbon mics with quiet sound sources.
-
GAIN switch range 20 - 80 dB. GAIN/LINE mode switch, gain is reduced by 30 dB in LINE mode.
-
Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.
-
Selectable 6 dB/octave two frequency high pass filter at around 40 (HP1) and 170 Hz (HP2).
-
Tantalum capacitors in the signal path.
-
Switchable impedance in MIC mode, 1200 or 300 Ohms, will change the tone of most mics. The input impedance in LINE mode is 10 kohm.
-
Switchable phantom power and absolute phase.
-
A high-impedance instrument input for any sound module, electric guitar or bass.
-
A simple but effective 4-step LED output level meter.
-
The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.
-
Combo XLR/TRS input jack and separate output XLR and TRS jacks for flexible connections.
-
Insert jack for inserting EQ´s and other units.
-
Selectable 600 ohm output termination.
-
The pcb is prepared for the Carnhill input transformer.
-
External power supply to avoid interaction with the audio circuits and transformers.
-
A solid build quality that will last many years of normal use.
The MKIII has the following new features compared to the MKII:
-
Tantalum capacitors in the signal path.
-
Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.
-
Selectable two frequency high pass filter, 6 dB/octave at 40 or 170Hz.
-
The pcb is prepared for the Carnhill input transformer.
-
Revised and less complicated GAIN switch with a separate switch for MIC/LINE selection.
-
All GAIN settings can also be used in LINE mode .
| • Road proof housing
• High quality components
• Professional balanced XLR outputs
• Level control
The ASC-202 converts consumer level stereo RCA signals to balanced XLR professional line level, and back. One side of the unit, has two XLR inputs and stereo RCA outputs. The other side has stereo RCA inputs and two XLR outputs. Each side has stereo level controls. A possible application of the SC-13 is to use it as a level control in balanced audio lines.
The DAP Pro Audio Solutions are a complete line-up of audio tools for the professional musician or audio engineer. It is a series of audio modifying tools like mini-mixers, pre-amps and converters available in active or passive models. All audio solutions are designed to meet the highest stage and audio demands and feature a metal road proof housing with rubber feet and easy accessible controls. The units also have a small footprint which make them ideal to be used and placed in any environment where space is critical.
Specifications Frequency Response: 20Hz-20KHz
Inputs: XLR/Jack Combo, RCA
Outputs: XLR male, RCA
Input sensitivity RCA in: -10 dBv
Input Impedance RCA in: 10 kOhm
Input sensitivity XLR/Jack in: +4 dBu
Input Impedance XLR/Jack in: 20 kOhm
Output voltage RCA Out: -10 dBV
Output Impedance XLR Out: 100 Ohm
Output voltage XLR Out: +4 dBu
Output Impedance XLR Out: 200 Ohm
Power supply: 18V AC (adapter included)
Dimensions: 53 x 158 x 135 mm (HxWxD)
Weight: 0,65 Kg |
At PreSonus, weʼve been designing preamps for a long time, and we always focus on audio quality first. So when we decided to upgrade our popular TubePre V2, we focused on improving an already high-quality sound—without jacking up the price. Like the originalTubePre, the new version is a fully professional tube preamp, with a dual-servo (no capacitors) gain stage that lets you boost the program signal to smoking hot levels without significantly increasing the background noise. Discrete components and high-voltage operation offer dynamic range and detail not found in other single-channel tube preamps in its class.
Housed in a rugged case, the TubePre V2 rear panel sports separate unbalanced, ¼” instrument and balanced, XLR mic inputs and unbalanced ¼” and balanced XLR line outputs. Weʼve included all of the extras you need for professional operation including a high-pass filter, phantom power for condenser mics, polarity reverse switch, and a backlit VU meter.
|
Reviews
There are no reviews yet.