| Content |
An elegant solution for personal monitoring on stage or in the studio.
FEATURES:
XLR microphone input
XLR microphone Thru, microphone output to send to main mixer
1/4" stereo mix input
1/4" stereo mix Thru for daisy chaining additional units
Microphone volume control
Mix volume control
Two headphone outputs
18 Volt AC adapter included
| In-ear monitor amplifier for personal monitor applications. High power and \"drummer proof\" headphones output. Dual XLR inputs allow for 2-channel mono or stereo operation. Switchable stereo/mono operation with mix function. Level and Balance/Mix controls. Runs up to 12 hours on a 9 V battery (not included). Integrated current limit protects your ears and headphone. Convenient belt-pack clip included. Mounts easily on a standard mic stand with 5/8” and 3/8” thread.
| Brand |
BEHRINGER |
| Model |
P1 |
| Part Number |
000-AZM |
| Mixing Channels |
2 |
| Warranty |
1 Year |
| Application |
Portable PA |
| Series |
P series |
|
MyMONITOR - Personal Headphone Monitor Mixer Overview
Problem: A performer needs to hear him/herself through headphones exclusively or mixed
with the output of a mixer, CD player, tape deck, or other stereo line level source. Only the
mic signal, however, should be going to the main mixer.
Solution: Connect MyMONITOR between the mic and line source, and the mixer. The Mic
and line Monitor levels can then be adjusted for mix and volume through the headphones.
Only the mic signal will go to the board. And since MyMONITOR can be AC or battery powered,
the unit can be used on a large stage or wherever there is no AC outlet nearby. Dynamic or
condenser mics can be used since phantom power would come through the Mic Thru jack from
the mixer or other source.
MyMONITOR - Personal Headphone Monitor Mixer Specifications:
Signal To Noise Ratio 90dB
Gain 15dB (1/4 in), 50dB (XLR)
Maximum Input Level -20dB mic, 40dB Monitor
Output Impedance 10 ohms
Power Requirements 12V DC (Adapter included) or one 9V battery
Phantom Power ON/OFF switch
Power LED indicator
Dimensions 4.5x2.75x1.5 inches (112mm x 72mm x 40mm)
Weight 1.3lb (590g)
| LD Sytems HPA 4 - a compact and powerful headphone amplifier
The LDHPA4 has small dimensions, can handle up to 4 headphones and has an output power with no equal in its class. That means high volume with no distortion. With these features the LDHPA4 is an essential tool for every project- and home studio.
Specifications
Product type
Headphone Amp:
Inputs
2
Input connectors
6.3 mm TRS , RCA
Input impedance
1 k Ohm(s)
Outputs
2
Output connectors
6.3 mm Jack
Power output
4 x 100 mW
Minimum connected impedance
10 Ohm(s)
Frequency response
20 - 20.000 Hz
Controls
4 x headphone volume , Mono/stereo switch
Indicators
Power
Operating voltage
External Power Supply
Operating voltage
24 V DC
Cabinet material
metal
Cabinet surface
painted
Width
94 mm
Height
48 mm
Depth
82 mm
Weight
0,27 kg
Accessories (included)
power supply |
The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.
In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.
The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.
Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.
The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.
|
The compact HX-3 Headphone Distribution Amplifier is the perfect accessory to quickly provide three high-performance stereo headphone feeds with individual level controls from line-level sources. The HX-3 can produce very high headphone levels with extremely low noise and distortion.
HX-3 Key Features
Great for radio, television, film, and music production applications, the battery-powered HX-3 accepts balanced XLR line-level inputs or unbalanced 1/4-inch and 1/8-inch stereo inputs. Its 1/4-inch loop-out can connect multiple HX-3's for additional headphone outputs. Headphones are connected to panel-mounted 1/4-inch stereo connectors.
The HX-3 has a durable aluminum chassis to withstand the punishment of field and studio environments. The unit is powered by inexpensive batteries (two-AA) or external 5-18 VDC.
The HX-3 can add headphone outputs to the 552, 302, MixPre-D, MM-1, and USBPre-2.
HX-3 Key Features List - Three isolated headphone outputs with individual volume controls.
- 125 dB dynamic range with flat frequency response.
- Durable 1/4-inch connectors, panel mounted for strength.
- Stereo or mono monitoring.
- Peak LED indicates headphone overload.
- Two balanced XLR line level inputs or unbalanced 1/4-inch and 1/8-inch stereo inputs.
- Loop Output to connect additional HX-3's in series.
- All-metal connectors solidly mounted to the chassis for durability and RF immunity.
- Free from "Pin-1" grounding problems.
- Internal battery-power for up to 18 hours from two AA alkaline batteries.
- Chassis-isolated 5 to 18 VDC input for easy external DC powering.
- Power LED indicates low battery power.
- High strength, extruded aluminum chassis with protective metal end panels.
|
Reviews
There are no reviews yet.