| Content | Cable for connecting a guitar or bass to the SK portable transmitter. 6.3mm mono jack to 3pin 3.5mm screw type jack
Designed to be used with the EW-G3 and EW-D1 portable transmitters
- For EW systems (for SK transmitter)
- Plug: 6.3 mm mono jack
- Length approx.: 100 cm
- Not suitable for Freeport!
| Specifications WS1000R
- Frequency Range: 790.850 MHz - 813.800 MHz
- Switching bandwith: 0.025 MHz
- No. of channels: 160 (10 groups of 16 CHN)
- Sensitivity: -94 dBm for 30 dB SINAD, typical
- Image Rejection: >60 dB
- S/N Ratio: >105 dB (A)
- T.H.D
- Audio Output Level XLR connector: -12 dBV
- 1/4inch connector: -18 dBv
- Audio Response: 60 Hz - 16 kHz
- Dynamic Range: >95 dB A-weighted
- Dimensions (W x H x D): 212 mm x 45 mm x 160 mm
- Power Requirements: 12-18 V dc at 400mA
|
Shure UA-870WB Directional UHF Antenna
A Directional Antenna for Shure U4 and ULX Receivers!
The Shure UA870 is an active UHF wireless directional antenna featuring a log periodic dipole array.
When compared to an omnidirectional 1/2-wave antenna, the cardioid pattern provided by the UA870
offers enhanced reception of the desired coverage area and greater rejection of RF signals outside the coverage area.
To compensate for coaxial cable signal loss, the UA870 has an on-board amplifier that offers user
selectable 3 or 10dB gain. The gain setting is indicated by two LEDs. Remote 12 Vdc power for the
antenna amplifier is provided by a Shure U4 receiver or a Shure UA840 antenna distribution system
through the connecting coaxial cable.
The UA870 can be mounted on a microphone stand, suspended from the ceiling, or mounted to a
wall using the integrated swivel adapter bracket. The UA870 is weather resistant for use outdoors.
For best diversity performance, use two UA870 antennas.
The UA870WB is a UHF wideband (470-900MHz) active directional antenna for U4S, U4D, ULXP
and ULXS receivers or UA844 and UA845 antenna distribution systems. |
Specifications
| Antenna Input Impedance: | 50 Ohm | | Antenna Output Impedance: | 50 Ohm | | Connectors: | TNC receptacle | | Gain: | 13 dB | | Bandwith: | 400 MHz | | Power Requirements: | DC 9 V | | Dimensions: | 35 mm x 65 mm x 75 mm |
This product is compatible with the LDWS100 series and also with the LDWS1000 series.
|
The IR-300M is a hands-free infrared wireless microphone. It eliminates problems with interference or eavesdropping, allowing simultaneous use in adjacent conference rooms or school classrooms. Since infrared wireless microphone system uses a frequency band that does not interfere with that of the TS-800 and TS-900 series infrared conference system, both systems can be simultaneously installed in the same location.
| Battery | IR-200BT-2 rechargeable battery for the infrared wireless microphone (option)
or AA alkaline dry cell battery (2 pieces). | | Current Consumption | Typ. 250 mA (2.4 V, Power selector switch: N)
Typ. 340 mA (2.4 V, Power selector switch: H) |
Infrared Emitter
| Wavelength | 870 nm (AM: Brightness modulation) | | Modulation Method | Frequency modulation | | Carrier Frequency | Channel A: 3.100 MHz
Channel B: 3.350 MHz | | Transmission Distance | Approx. 20 m (65 ft) (Power selector switch: H, in an unobstructed space)
Approx. 15 m (50 ft) (Power selector switch: N, in an unobstructed space) | | Tone Signal | 32.768 kHz | | Modulation Sensitivity | ±4.8 kHz (1 kHz, when SPL of 84 dB is input) | | Maximum Input Sound Pressure | 120 dB SPL | | Input Sensitivity Adjustment | Adjustment range: -9 dB to 0 dB (factory preset: 0 dB) | | Microphone Unit | Unidirectional electret condenser microphone | | Frequency Response | 100 Hz - 12 kHz | | Preemphasis | 300 μs | | Input | External microphone input (φ3.5 monaural mini jack) | | Battery Operation Time | Approx. 8 h (when the IR-200BT rechargeable battery for the infrared wireless
microphone is used, Power selector switch: N)
Approx. 6 h (when the alkaline battery is used, Power selector switch: N) | | Operating Temperature | 0 ℃ to +40 ℃ (32 ゜F to 104 ゜F) | | Operating Humidity | 30 % to 85 %RH | | Finish | Control section: ABS resin, metallic gray, paint, 50% gloss
Filter section: Polycarbonate, optical cut filter | | Dimensions | 64 (W) × 91.3 (H) ×27.3 (D) mm (2.52" × 3.59" × 1.07“) | | Weight | 130 g (0.29 lb) (with battery and strap) | | Accessory | Screw driver (for setting) …1, Color label (6 colors) …1 |
|
Shure PS9E Power Supply for P4HW
- Suitable for the follpwing: T11, LX1, UT1, ULX1, MX1BP, P2R, P4R
- For external power supplies
- Consists of a PS21E power supply + 9V block
|
Reviews
There are no reviews yet.