SENNHEISER E-912 HALF-CARDIOID CONDESER BOUNDARY MICROPHONE

The e 912 is a pre-polarized condenser boundary microphone with
half-cardioid pick-up pattern. Its acoustic properties have been
optimized for instruments, vocals and speech. The e 912 is an ideal
choice for pianos, theatre and opera productions, conference applications,
altars and lecterns.To optimally match the installation environment,
the e 912 is available in black or creme white.

Features
Frequency response and sensitivity optimized for picking up instruments,
vocals and speech
Unobtrusive, flat housing
Extremely rugged and step-resistant
Shock-absorbing rubber base
Mounting slots for table installation
Gold-plated XLR connector
Integrated pre-amp 
Delivery Includes
e 912 Microphone
Pouch
User manual

Technical Data
Transducer principle (Microphone)  permanently polarized condenser 
Pick-up pattern  half-cardioid 
Sensitivity in free field, no load (1kHz)  10 mV/Pa 
Max. Sound pressure level (aktiv)  135,6 dB 
Equivalent noise level  26 dB(A) 
Phantom powering  48 V / 1,1 mA 
Nominal impedance  Min. terminating impedance  1000 Ohm 
Dimensions  126,5 x 105 x 26,5 mm 
Weight  ca. 550 g 
 

C 562 CM 

Small, low-profile boundary layer microphone
Wide frequency range
High sensitivity
Ideal for inconspicuous installation in a room
Suited for surveillance or recording
 
The C 562 CM flush-mount boundary microphone uses the same transducer as the C 562 BL.
The C 562 CM has been designed specifically for permanent, "invisible" mounting in ceilings,
walls, tables, stage props, etc.
Owing to its high sensitivity, the C 562 CM is a perfect tool for surveillance or live recording
since a single microphone can cover an entire room. The supplied XLR phantom power adapter
connects to the microphone cable through a miniature connector so installation holes can be
smaller than the diameter of the phantom power adapter.
 
SPECIFICATIONS:
Polar pattern omnidirectional (hemispherical)
Frequency range 20 to 20,000 Hz
Sensitivity 25 mV/Pa (-32 dBV)
Max. SPL 130 dB (k=1 %)
Equivalent noise level 16 dB-A
Signal/noise ratio (A-weighted) 78 dB
Impedance 600 ohms
Recommended load impedance >2000 ohms
Supply voltage 9 to 52 V phantom power to DIN/IEC
Current consumption Connector 3-pin XLR
Cable 0.5 m (20 in.)
Finish matte nickel plated
Dimensions 20 dia. x 28 mm (0.8 dia. x 1.1 in.)
Net weight 30 g (1.1 oz.)
Shipping weight 195 g (76.9 oz.)
 

    Designed for Broadcast, House of Worship, Pro Music, and other applications.
    Half-cardioid polar pattern
    Boundary layer
    Ultra-thin profile (16 mm) housing
    Rubber non-slip bottom pad and strong steel screen
    Integrated pop filter

Case Material    Die cast zinc
Connector Type    3-pin XLR
Element    Back Electret Condenser
Finish    Non-reflecting Black
Finish    White
Impedance, Low-Z balanced    200 Ω
Mic Type    Boundary
Open Circuit Voltage    25 mV/Pascal
Polar Pattern    Cardioid
Wired/Wireless    Wired
Height    16 mm (0.63“)
Width    94 mm (3.7“)
Depth    123 mm (4.84“)
Weight Net    12.63 oz (358 g)

With three cardioid condenser elements in a single housing, the phantom-powered U843R offers a remarkably versatile tool for surface-mount installations. Levers on the microphone base allow easy reorientation of two elements to offer 360° or 300° coverage. Since elements can be powered and used individually or in any combination, further flexibility is easily achieved. For example, with two elements powered, the microphone can provide a figure-of-eight polar pattern; with a single element powered, the microphone functions as a standard cardioid boundary microphone. Installation and repositioning are extremely quick, thanks to four recessed pathways on the base of the microphone that enable the user to route the cable as required to accommodate any installation requirements; no tools or disassembly are needed. The microphone also offers Audio-Technicaʼs innovative UniGuard® RFI-shielding technology.

• Three cardioid condenser elements mounted in a single housing
• Easily reposition two elements (via levers on the microphone base) to offer 360° or 300° coverage; each element can be powered and used individually or in any combination
• Also functions as a stereo boundary microphone
• Provides full, efficient and flexible coverage—fewer microphones required
• Small-diameter capsules near boundary eliminate phase distortion and deliver clear, high-output performance
• Low-frequency attenuation improves sound pickup without affecting voice quality
• Cable routes through any of four recessed pathways on the microphone base (or down for direct feed through a table surface); no tools or disassembly required
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Heavy die-cast case and non-slip silicone foam bottom pad minimizes coupling of surface vibration to the microphone
• Low-profile design with low-reflectance finish for minimum visibility

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Hemispherical Cardioid x3 (combine to omni-directional or bidirectional)
• Frequency Response: 70-16,000 Hz
• Open Circuit Sensitivity: –37 dB (14.1 mV) re 1V at 1 Pa
• Impedance: 100 ohms
• Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range (Typical): 105 dB, 1 kHz at Max SPL
• Signal-to-Noise Ratio: 65 dB, 1 kHz at 1 Pa
• Phantom Power Requirements: 11-52V DC, 2 mA typical
• Switch: The lever of elements can adjust the proper position
• Weight (Less Cable): 160 g
• Dimensions: 20.0 mm - height
  85.0 mm – maximum body diameter
• Cable: 7.6 m long (permanently attached to microphone), 4 mm diameter, 6 conductor, shielded cable; output end stripped and tinned for connection to electronic device
• Accessories Furnished: Soft protective pouch

A wide range condenser microphone with a cardioid polar pattern, the ultra-smart U891RCx is equipped with local or remote switching options. For flexible control in conference and boardroom installations, the unit's external contact closure ability allows a user to trigger an external device - a camera, for instance - from a switch on the microphone. Another ease-of-use feature: the microphone's electronic on-off switch can be set to three operating modes: touch-on/touch-off, press to talk, and press to mute. The mic is also equipped an 80 Hz low-cut UniSteep® filter to reduce pickup of low-frequency ambient noise. Its red LED status indicator can be controlled remotely. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; a unique rotating PivotPoint® connector changes the cable exit point - no tools required. It requires 11 to 52V DC phantom power, which operates the microphone and switch circuitry.

• Designed for surface-mount applications such as high-quality sound reinforcement, conferencing, distance learning and other demanding sound pickup situations
• Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/touch-off," "touch-to-talk" and "touch-to-mute“
• External contact closure capability permits control of remote devices from microphone switch
• External LED control allows for accurate depiction of the live status of the microphone
• PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
• Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
• Low-profile design with low-reflectance black finish for minimum visibility

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
• Frequency Response: 30-20,000 Hz
• Low Frequency Roll Off: 80 Hz, 18 dB/octave
• Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
• Impedance: 200 ohms
• Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range: 104 dB, 1 kHz at Max SPL
• Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
• Phantom Power Requirements: 11-52V DC, 4 mA typical
• Weight: 266g
• Dimensions: 108.0mm long, 84.0mm maximum width, 23.0mm height
• Output Connector: TB5M-type
• Cable: 7.6m long, 3.2mm diameter, 5-conductor shielded cable (2 conductors under shield; 3 control wires outside shield); TA5F-type connector at microphone end, output end stripped and tinned for connection to electronic device