Content |
• Sealed Optics
• DMX & ILDA control
• 20K Scanner pair
• Very wide beam angle
• Runs pre-programmed shows from SD card
• Flightcase, ILDA cable & 1G SD card included
The Galactic RGB 850 is the top model of the Galactic Series. Though the power is only 850mW, with help of the new 200mW 638nm red laser, the visual brightness is around a 1.2W traditional RGB laser with 660nm red laser. It has beautiful clear colors created by these 3 separate laser-diodes, Red, Green and Blue with TTL modulation. The RGB850 can be controlled by DMX and has many built-in figures and patterns. It can project two built-in patterns at the same time. You can also create your own designs and shows with any kind of ILDA laser software. The RGB850 is equipped with a 20K scanner pair which makes faster and bigger projections possible with less flickering. For rental solutions you can use the SD card slot to run pre-programmed shows without any controller.
Attention, the laser only works when the interlock connector is connected with a remote interlock (ordercode 51316). You can test if the laser works properly with the included test connector. If you use the laser in public area's a remote interlock is necessary for safety regulations.
Specifications
Power Input: AC 100-240V, 50/60Hz
Power Consumption: 68 Watt
Laser Color: Red, Yellow, Green, Blue, Purple, Cyan, White
Laser Power: 850mW (200mW 638nm Red, 150mW 532nm Green, 500mW 450nm Blue)
Laser Modulation: TTL
Laser Class: 4
Scan Speed: 20K
Scan Angle: +/-60˚
Control Modes: Auto, Sound, Master/Slave, DMX, ILDA, SD-Card
Control Display: LCD
DMX Channels: 13
Data Connector: In/Out, XLR 3Pin & Sub-D 25 Pole
Safety Features: Key switch, Interlock, Safety eye
Laser Safety: EN/IEC 60825-1 Ed 2, 2007-03
Dimensions: 335 x 240 x 165mm (excl. bracket)
Dimensions flightcase: 760 x 435 x 315mm
Weight: 11,5 kg
Accessories: 2 Keys, Interlock test connector, flightcase, ILDA cable, 2G SD card
|
JB Systems Lounge Laser DMX
Der JB Systems Lounge Laser DMX ist ein Effekt-Laser, der durch eine spezielle Rastertechnologie eine große Anzahl einzelner Laserstrahlen aufteilt, die in alle Richtungen zeigen und so einen verblüffenden, raumfüllenden Effekt erzeugen. Durch die Plug and Play-Funktion werden keine teuren Steuergeräte benötigt. Der JB Systems Lounge Laser DMX kann über die DMX-Steuerung (1 oder 7 Kanäle), Sound-to-Light und Master/Slave Betrieb laufen.
JB Systems Lounge Laser DMX:
- Effekt-Laser
- Betriebsmodi: DMX-Steuerung (1 oder 7 Kanäle), Standalone (musikgesteuert oder automatisch), Master/Slave-Funktion
- Spannungsversorgung: 230 V
- max. Leistung: 128 Watt
- CW Laser grün: 40 mW/532 nm
- CW Laser rot: 150 mW/650 nm
- LED Leistung: 5 Watt/blau
- Laserschutzklasse: 3B
- EN/IEC: N60825-1:1994 + A1:2002 + A2:2002 + COTT
- Maße: 8,6 x 23,3 x 17,6 cm
- Gewicht: 1,6 kg
| Sporting diode and DPSS lasers with 3 mm beam diameters and a maximum divergence of 1 mrad only the WOOKIE 200 RGY provides red, green and yellow colors and 200 mW output.
The Wookie Series animation laser lights provide vibrant, highly visible animations with precision beams, 32 lively pattern presets and high speed 5 Kpps stepper motors with a 60° scan angle. They are controllable via DMX in 3-channel and 9-channel modes, the integrated microphone with adjustable sensitivity and capable of master, slave and standalone operation. Each Wookie laser light sports a compact, high quality aluminium enclosure with 3-pin DMX connectors, IEC mains inlet and adjustable mounting bracket. A key switch prevents unauthorized use, and the bright display with four function keys allows easy manual operation. The Wookie Series laser lights come with a convenient infrared remote control.
- Item number: CLLWOOKIE200RGY
- Product type: LASER
- Total power: 200 mW
- Colour spectrum: RGY
- Wavelength(s): 650nm, 532nm
- Beam Data: approx. 3 mm / 1 mrad divergence
- Laser sources: Laser diode
- Laser class: 3B
- Scanner: High speed stepper motors, 5 kpps
- Max. scan angle: 60 degrees
- Operating modes: DMX-512, Auto, Sound Control
- DMX input: 3-pin XLR
- DMX output: 3-pin XLR
- DMX mode: 3-channel, 9-channel
- Controls: Mode, Enter, Value Down, Value Up
- Display elements: LED display
- Power supply: AC 100-240 V / 50-60 Hz
- Power consumption: 50 W
- Power connector: IEC power socket male
- Housing Material: metal
- Housing colour: black
- Dimensions (WxDxH): 180 x 90 x 192 mm (excluding bracket)
|
Cameo D FORCE 5000 RGB
- 5,000 mW total output power
- User-adjustable beam alignment
- Dust-proof aluminium housing for minimum maintenance
- High-speed high-performance 30 Kpps galvo scanner @ 8° ILDA
- Analogue modulation for up to 16 million colour shades
- Precision beam with minimum divergence for razor-sharp projections
- Interlock emergency stop signal output
- ILDA interface for software control
- Scan Fail Safety system
- Neutrik PowerCON input and output
- Temperature-controlled low-noise fan for cool and quiet operation
- Optional adapters for Pangolin safety lenses and DiscoScan V2 360° wide-angle lens (CLLDFORCEAPSSL, CLLDFORCEAPDSL)
Delivering a massive total output of 5,000 mW, the D.FORCE 5000 RGB creates stunning graphics projections with analogue modulation for up to 16 million colour shades. The highly professional diode-only show laser generates a razor-sharp beam with 2 mm diameter and less than 1 mrad divergence, and the use of a 638 nm diode ensures a highly visible, intense red colour. Eliminating the need for servicing, an easily accessible beam alignment system enables the user to quickly perform adjustments if necessary. The D.FORCE 5000 RGB's pure diode design provides an increased life span and much higher efficiency compared to temperature-dependent DPSS laser sources.
The D.FORCE 5000 RGB features a high-speed 30 Kpps scanner @ 8 degrees ILDA, a wide 50° scan angle and an ILDA interface on 25-pin D-sub connectors for software control.
The dust proof dual layer aluminium housing separates the optical components from the power supply and fan to ensure maximum performance while minimizing maintenance. It provides Neutrik powerCON input and output connectors plus a key switch to prevent unauthorized use. For audience safety the D.FORCE 5000 RGB is equipped with a Scan Fail Safety system, and an optional adapter permits the use of Pangolin lenses.
Total power
5,000 (R: 1,400, G: 1,400, B: 2,300) mW
Laser sources
Laser diode
Max. scan angle
max. 50 °
Operating voltage
100 V AC - 250 V AC
Power connector
Neutrik PowerCon
Housing material
aluminium
|
- Animation laser with high speed 5 Kpps stepper motor
- 60° scan angle
- Precision beams with minimum divergence
- 32 pattern presets
- DMX, sound and infrared control plus auto function
- Master, slave and standalone modes
- Display with 4 function keys for easy manual operation
- Rugged aluminium enclosure with key switch
- Includes handheld infrared remote
Projecting animations with red, green and blue color mixes the WOOKIE 400 RGB delivers an output of 400 mW from 3 mm beam diameter diode and DPSS lasers with no more than 2 mrad divergence.
The Wookie Series animation laser lights provide vibrant, highly visible animations with precision beams, 32 lively pattern presets and high speed 5 Kpps stepper motors with a 60° scan angle. They are controllable via DMX in 3-channel and 9-channel modes, the integrated microphone with adjustable sensitivity and capable of master, slave and standalone operation. Each Wookie laser light sports a compact, high quality aluminium enclosure with 3-pin DMX connectors, IEC mains inlet and adjustable mounting bracket. A key switch prevents unauthorized use, and the bright display with four function keys allows easy manual operation. The Wookie Series laser lights come with a convenient infrared remote control.
Wavelength
447 nm , 532 nm , 650 nm
Beam Data
approx. 3 mm / 2 mrad divergence
Laser sources
DPSS , Laser diode
Scanner
High speed stepper motors, 5 kpps
Operating modes
Auto programs , DMX 512 protocol , sound control
DMX output
XLR 3-pin female
DMX mode
3-channel , 9-channel
Controls
Enter , Mode , Value Down , Value Up
Operating voltage
100 V AC - 240 V AC, 50 - 60 Hz
Power connector
IEC power connector male
Weight
2 kg
|
Plug & play: no expensive controllers needed!
a multifunctional infrared remote can be used to control the functions
standalone mode with built-in microphone or automatic shows can be selected
all kinds of strobe effects
adjustable mounting bracket (stand) and power adapter included
key actuated on/off switch for additional safety
complies to EN/IEC 60825-1 Ed2, 2007-03 for Laser Safety
Technical Details:
Mains Input: AC/DC Adapter 230V AC -> 12V / 600mA
Power consumption: 5,7W
Laser Power: 40mW green CW laser (532nm), 100mW red CW laser (650nm)
Laser radiation class: 3B Laser
Safety Standard: EN60825-1:1994 + A1:2002 + A2:2002 + COTT
Patters: like Micro Star Laser, plus more patter
Operating modes: standalone mode with built-in or automatic
Remote control: inluded
Dimensions: 117 x 92 x 46 mm
Weight: 0,54kg
|
Reviews
There are no reviews yet.