SHURE BG 5.1 – Cardioid Condenser Microphone

SHURE BG-5.1 - Cardioid Condenser Microphone

The BG5.1 studio-quality condenser microphone is perfect for laying down accurate vocal tracks.

• High sensitivity, low noise, and specially-shaped frequency response for vibrant and clear vocals, particularly on digital and analog recorders
• Operation with internal AA battery or phantom power
• Steel mesh grille with built-in pop filter for extra durability and clarity
• Includes padded carrying case and break-resistant swivel adapter
• Frequency response: 70 to 16,000 Hz

The R?DE NT6 is specifically designed for difficult mounting applications. Although
clearly relevant to instrument mic'ing, the new NT6 is extremely well suited to any
situation where a small 'unobtrusive' but powerful microphone system is required.
The NT6 utilises the 1/2" (externally biased) gold sputtered true condenser transducer
used in the internationally renowned R?DE NT5. The capsule is designed to attach to
a custom made, multi-position swivel mount allowing it to be independently positioned
with ease.
To further increase the versatility of the NT6, it is supplied with 2 thread adaptors - 1/4"
to 5/8" and 1/4" to 3/8" that enable the capsule assembly to be securely attached to a
wide variety of mic stands, tripods and boom poles.
The capsule is connected to the pre-amplifier (body) by a custom 3 m Kevlar? fibre reinforced
cable. Housed within the heavy duty satin-nickel-plated body, is a state-of-the-art low noise
balanced output preamplifier, exhibiting a wide dynamic range and full frequency response.
The surface-mount pre-amplifier circuit also incorporates a 2-position variable pad: 0 dB an -10 dB
attenuation, and a 2-position variable high-pass filter that enables you to step from a flat response
to 80 Hz high pass filter; both conveniently located away from the capsule, providing additional
control without the need to move the capsule once in position.
The NT6 is intended for Film, Television, Broadcast, Live Performance, Theatre, Television,
Surround and Environmental recording applications or wherever your imagination takes you.
The NT6 is produced in R?DE's design and manufacturing facility in Sydney, Australia. Utilising
state of the art computer controlled machining and assembly technologies, R?DE is able to
achieve levels of finish and repeatability of the most exacting standards and tolerances.
The NT6 comes supplied with Microphone Preamp (Body), Capsule, 3 m Kevlar? fibre reinforced
cable, RM5 Stand Mount, 2-axis Swivel Mount, 2 thread adaptors, ZP1 Zip Pouch and WS5 Wind Shield.
 
FEATURES:
? 1/2? (externally biased) gold sputtered true condenser capsule ? Heavy duty satin-nickel-plated body
? 2-position variable pad: 0 dB and -10 dB ? 2-position variable high-pass filter: flat and 80 Hz ? Surface
mount technology ? Low noise ? Wide dynamic range ? Full frequency response ? Supplied complete
with 2-axis swivel mount, 2 thread adaptors, M5 clip, WS5 (Black) Wind Shield and Soft Pouch ? Designed
& manufactured in Australia ? Full 2 year guarantee 
 
Operation power:
The NT6 is designed to operate from phantom power to the P48 standard. The NT6 will operate
between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output XLR connector. 
Operation output impedance:
Output Impedance: The NT6 will operate satisfactorily into a load impedance as low as 1 kΩ. If a
load below this is used, the output signal level will be reduced. The NT6 output is balanced between
pin 2 (hot) and pin 3 (cold). Pin 1 is ground.
 Acoustic principle:
Externally polarised 1/2" (13mm) pressure gradient condenser
Directional pattern:  Cardioid
Frequency range:
40 Hz ~ 20,000 Hz selectable HPF @ 80 Hz/12 dB/octave
Output impedance: 200 Ω
Signal noise ratio din iec 651:
75 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 19 dB SPL (per IEC651, IEC268-15)
Maximum spl:
138 dB (@ 1% THD into 1 kΩ)148 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity:
-38 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB
Dynamic range din iec 651: 119 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Weight: 386 grm.
Maximum output voltage: 6 dBu (@ 1% THD into 1 kΩ)
Pin assignment:
3 pin XLR, balanced output between pin 2(+), pin (-) & pin 1 (ground)
 

The e 865 is a fully professional super-cardioid vocal microphone utilising the very best in condenser microphone technology to achieve new standards of quality and sound. The microphone capsule insorporates special blast/pop protiction plate to shield the diaphragm from excessive sound pressure levels. ON/OFF Switch.

• Pick-up pattern : super cardioid
• Sensitivity in free field, no load : (1kHz) 3 mV/Pa
• Max. Sound pressure level (aktiv) : 150 dB
• Nominal impedance : 200 Ohm
• Min. terminating impedance : 1000 Ohm
• Dimensions : d 47 x 193 mm
• Weight : w/o cable 311 g
• Frequency response (microphone) : 40.....20000 Hz
• Phantom powering : 12 - 48 V

The Stereo wonder. The new NT4, a visually striking microphone that solves
the age-old problem of stereo recording by eliminating the need to purchase
matched pairs and the associated complex set-up bars and adaptors to get
professional results. With a fixed 90 Deg. X/Y configuration and perfectly
matched stereo condenser capsules, the NT4 lets you record any source with
immaculate stereo detail.
The NT4 has a 128 dB dynamic range, 143 dBA SPL and low self-noise. Offering
selectable battery or phantom power operation with power indicator light, the NT4
is ideally suited to both studio and location recording.
The NT4 comes supplied in a custom carry case with a windshield, XLR to mini-jack
and dual XLR cables for portable DAT or professional balanced input connection.

SPECIFICATIONS:
Acoustic principle:
Stereo Microphone. 90° XY placement. Each side comprises an
externally polarised single diaphragm condenser transducer
Directional pattern:  Cardioid per capsule
Frequency range:  20Hz - 20kHz
Output impedance: 200? per side
Signal noise ratio din iec 651: 78dB
Equvalent noise:128 dB
Power supply voltage:
P48 (38V?52V), P24 (20V-26V), P12 (10.8V-13.2V), 9V battery
Current consumption:  4 mA, 2 mA, 2.8 mA, 2.4mA
Weight without battery:  480g
Weight with battery:  2.3kg