| Content |
Shure PM4E 6in-6out Personal Monitor Mixer
The P4M is a highly versatile four-channel, two-bus stereo mic/line mixer designed to optimize
use of personal (in-ear) monitors like the Shure PSM 400 in live performance. The P4M features
four balanced mic/line inputs, each with level and panning controls. Corresponding XLR split outputs
allow input signals to pass through the unit unaffected, while providing an independent mix.
Personal Stereo Monitors
When coupled with personal monitors, the P4M allows performers the ability to adjust personal mix
levels onstage - even during a performance - without affecting the front-of-house system. This enables
users to create and maintain consistent monitor mixes, regardless of what the venue can provide for monitors.
The P4M is available individually for use with Shure PSM 600 and PSM 700 Personal Monitor Systems; or
packaged with Shure's PSM 400 Hardwired and Wireless Performance Packs.
Installed Sound Systems
The P4M can also be used as a small "piggyback" mixer in applications such as houses of worship, or courtrooms.
The unit acts as a console bypass when a permanent installation of a large, operator-controlled mixing console may
require just a few microphones for smaller events. This allows the user easy access and control of up to four signals
without having to utilize the larger console. Given its dual-bus output capabilities, the P4M can also serve as a "two zone"
mixer, routing any combination of mic or line-level signals to two different zones.
More Than Four Inputs
The P4M has a pair of 1/4-inch auxiliary inputs that can be used to add channels from other sources. For example
multiple P4M mixers can be linked together to increase the number of inputs. In addition, sources not present in the original
mix - such as a click track for live percussion - may be included via the auxiliary inputs.
Measurement Conditions (unless otherwise specified):
full gain; 1 kHz, one channel activated; >source impedances: Mic 150 ohms, Aux Level 150 ohms; terminations: Line 600 ohms.
Frequency Response (Ref 1 kHz, controls centered)
20 Hz to 20 kHz +/- 2 dB
Input Specifications
Input
1-4 (front panel) Aux In
Gain (Maximum) 43 dB 0 dB
Impedance (at 1 kHz) 5800 ohms 18 kilohm (each)
9100 ohms (1/L mono)
Input Clipping Level +12 dBV +12 dBV
Crosstalk -100 dB -90 dB
Common Mode Rejection > 75 dB > 70 dB
Output Specifications
Output
Split 1-4 Mix Out
Impedance N/A 500 ohm (unbalanced)
1 kilohm (balanced
Output Clipping Level N/A +5 dBV (10 kilohm balanced
load, -30 dBV input ch. 1-4)
Noise (100 Hz to 22 kHz) -110 dBV -100 dBV (all controls CCW)
-62 dBV (all controls CW)
Distortion (THD) at 1 kHz .0005% |
Introducing the ES947LED, the new LED-equipped version of the Engineered Sound ES947 table-mount boundary microphone. The ES947LED features a touch-sensitive capacitive switch and LED status ring.
The cardioid condenser ES947/LED increases usability with a new toggle switch and LED status ring - which displays red when muted and green when switched on. The new LED-equipped version of the highly respected ES947 also features improved sensitivity and sound-to-noise ratio, perfectly suited to todayʼs digital matrix mixers.
The ES947/LED is available in black and white.
ES947LED Specifications 263 KB
|
12V AC-adapter for PS 4000, ASU 4000, HUB 4000, HPA 4000, CU4000 or SR 4000 | Gravity MA 3D A POP 1 Traveler 3D Arm with Pop Filter
The Traveler Series' Pop Filter with 3D Arm
Every bit of weight counts when you're travelling by plane or truck from one gig to the next. After all, you can't always rely on the concert venue having the right tool available for you when needed.
The Pop Filter with 3D Arm MA 3D A POP 1 can be taken everywhere you go. It's so light and space-saving, there's absolutely no need for you to worry about weight or storage space.
With this tool you can enhance your voice- and vocal recordings by placing the high-quality pop filter, with double nylon mesh and a large screen diameter of 15.7 cm between you and your microphone. This way you avoid unwanted pop noises and clipping.
Its fastening mechanism is quick and easy to assemble. The large clamping range from 15 to 35 mm lets you mount it on all popular microphone stands, and the three joints' 360° rotation options allow you to install it as you like. Simply loosen, adjust and tighten the wing-screws. Voila - you're all done! Once set, the MA 3D A POP 1 stays locked in place.
Gravity® has once again delivered a small, useful and reliable product for you to round off your collection of stands.
| Product type |
Microphone Accessories |
| Type |
Pop filter |
| Material |
Plastic, Polyamide |
| Color |
Black |
| Joint adjustment |
Wing screw |
| Joint rotation |
360° |
| Joint tilt |
180° |
| Arm length |
400 mm |
| Suitable for mounting on |
Microphone Stands |
| Thread size |
3/8” |
| Screen diameter |
157 mm |
| Setup |
Double nylon screen, plastic frame |
| Suitable for tube diameter |
15 - 35 mm |
| Weight |
0,377 kg |
| Portable Battery phantom power supply for microphones with TQG and AKG connection.
Balanced XLR output
2 three-pole TQG male inputs (Mini XLR)
Both inputs adjustable
On-off switch
Mic / Line level in the output switchable
9 V battery power
20 hours of operation with 1 battery
Power LED |
The new AT8657/LED table-mount microphone adapter adds functionality to quick-mount gooseneck models from the Audio-Technicaʼs Engineered Sound, Unipoint and ProPoint installation mic ranges and ES945 and ES947 boundary microphone models.
The new AT8657/LED features a touch-sensitive capacitive switch surrounded by an illuminated LED status ring that can be set between red (mute) and green (on). Its integrated 3-pin XLR allows the table-mounting of gooseneck microphones with XLR connectors while the AT8657/LED has a 5-pin XLR out for audio and control data.
AT8657LED Specifications 270 KB
|
Reviews
There are no reviews yet.