TANNOY PRECISION-8D ACTIVE STUDIO MONITOR

Precision 8D
The active versions of the Precision range incorporate powerful digital amplification
and advanced electronic processing that together take full advantage of the drivers?
capabilities. The result is greater dynamic range and low-frequency extension, higher
output levels, lower distortion and enhanced reliability.

MAIN FEATURES

From the front:
40mm MDF sculpted baffle ? stiff, heavy and rigid and minimises diffraction.
Recessed drive units flush with the baffle surface ? minimises diffraction.
10 point fixing maximises contact between drive unit and baffle.
Drive unit development using Klippell? analysis equipment to minimise offsets
and linearise the suspension components.
Cast chassis Tannoy Dual Concentric? point source constant directivity driver.
Effectively two drivers properly merged into one, with the HF mounted on the back
of the LF unit so that both drivers are on the same axis, As a result sound energy
is propagated from the same point and delivered through the centre of the low frequency
cone providing a true point source. This integrated approach provides a constant time
delay over the frequency spectrum offering better transient performance and sound
quality with better harmonic alignment than a displaced source monitor design. The
crucial benefit at the mix position is the delivery of a more natural and cleaner sound
with greatly enhanced intelligibility.
A key benefit of the Dual design is a very wide 'sweet spot' with an exceptionally even
response throughout the listening area and extraordinary transient response. This phase
accurate Tannoy designed drive unit has, for all these reasons, been the choice of
professional studio engineers for decades.
Tannoy SuperTweeterTM extends the amplitude response beyond 20kHz audibility to
50kHz to correct the phase response from 8kHz to 20kHz within the audible band. This
preserves the harmonic structure of sounds and the stability of the stereo image.
Smooth tweeter faceplate contours prevent diffraction and cavity effects.

From the side:
18mm MDF cabinet construction provides stiffness and minimises colouration.
Internal construction braces the sides and rear of the cabinet against the rear of the bass
driver to provide a rigid reactive mass for the moving cone assembly. Ensures fast tight bass
response and clear midrange.
Front baffle and rear panel tongued and grooved into the cabinet as a mechanical interlock
for safety if wall mounted.

From the rear:
Double insulated to prevent ground loops ? no safety earth required.
CSA/CE/CCC/CB full safety approvals including China.
Spare fuse in IEC mains connector.
On/Off mains isolator switch.
Substantial heat sinking for long term cool running and 24/7 reliability.
XLR and _? jack Combi connector for balanced input.
Switch adjacent to XLR selects digital or analogue input.
RCA input for SPDIF with 75 Ohm terminating impedance.
2nd RCA for SPDIF output for slaving a stereo pair.
Yellow LED indicator lights up when digital lock is achieved.
3-way switch selects which channel of the SPDIF stream is decoded,
marked Left/Right/Mono. Switching is post 2 channel DAC.
Trim/Gain control over +6dB/-12dB range reference 0dBV (0.775V) input
for full rated output.
Trim/Gain control works on SPDIF input post DAC.
Switch selection of 12dB/8ve 80Hz hi-pass filter for use with AV subwoofers.
First bank of 10 DIP switches controls LF alignment, mid/near/close field and
half/quarter/eighth space compensation.
Second bank of DIP switches controls mid band and HF shelving trim.
Note that the DIP switch flat setting is shown on the back panel artwork.
Small hole to the right of the right hand switch bank allows the factory set HF trim
on test to be fine trimmed by a service agent if a tweeter needs to be replaced.

TECHNICAL SPECIFICATIONS
PERFORMANCE 
Frequency response (1) 44Hz-51kHZ
Max SPL(2) 119dB
Distortion

The Genelec 8130A Digital Monitoring System has a 192 kHz/24 bit digital audio interface.
Due to its compact size, integrated construction, excellent dispersion and precise stereo
imaging, the 8130A is ideal for near field monitoring, mobile vans, digital audio workstations,
broadcast and TV control rooms, surround sound systems, home studios, multimedia
applications and also for use with computer soundcards. The Directivity Control Waveguide?
(DCW?) technology provides excellent frequency balance even in difficult acoustic
environments.
The integrated design allows the amplifiers and the drivers to be calibrated as a single unit,
eliminating the effects of component tolerances and ensuring consistent quality.
The all-aluminium Minimum Diffraction Enclosure? (MDE?) and advanced Directivity Control
Waveguide? (DCW?) technologies are carefully matched with advanced amplifier and electronics
circuitry. The low frequency response extends down to 55 Hz (-3 dB) while distortion is extremely
low due to a uniquely new rear reflex port design.
The 8130A has been specially designed to have a sufficient LF extension for most situations.
However if greater SPL's and a lower cutoff frequency are required, it can be complemented
with Genelec 7050B subwoofer.
The 8130A is very easy to set up and use, the only connections required are the mains supply
and the input signal. The female XLR input connector can be fed with either AES/EBU formatted
digital signal or analog line level audio signal. The Genelec 8130A automatically detects analog or
digital signals and directs them to the correct signal paths.

Technical Specifications
Input word length 16 - 24 bits
Input format AES/EBU
Digital input XLR female
Connector type 
Input Sampling rate
No de-emphasis  29 - 200 kHz
Input Sampling rate
Using de-emphasis 
Peak per pair with music material 108 dB SPL @ 1m
Drivers
Bass 5" magnetically shielded
Midrange -
Treble 3/4" metal dome, magnetically shielded
Crossover frequencies 3 kHz
Free field frequency
response 58 Hz - 20 kHz (± 2 dB)
Amplifier power /ch
Bass 40 W
Midrange -
Treble 40 W
Speaker dimensions (H x W x D)
mm 285 x 189 x 178 mm (Height with Iso-Pod? 299 mm)
inches 11 1/4 x 7 7/16 x 7 1/16" (Height with Iso-Pod? 11 13/16“)
Amplifier dimensions* (H x W x D)
mm Integrated in the speaker cabinet
inches 
Speaker weight 5.6 kg (12.3 lb)

    * Active studio monitors with USB audio interface
    * 4.25-inch magnetically shielded, inverted cone, copolymer woofer
    * 1-inch silk dome high frequency driver
    * 2 x 20 watts of internal stereo power
    * Two combination mic and instrument/line inputs
    * Two 1/8-inch stereo headphone outputs with level controls
    * Includes Cakewalk® Sonar LE music production software
    * Mic and instrument/line gain control with clip LED
    * 16-bit 44.1kHz/48kHz
    * Stereo RCA and 1/8-inch aux inputs
    * 2-position switch for no-latency direct stereo and mono monitoring
    * Mix control to balance computer and audio sources
    * USB and speaker cable included

MYTHO 6 is a two-way reference studio monitor that features a high quality large metal dome tweeter for the best vocal reproduction and a 6” neodymium vented woofer with a large sized 51 mm voice coil that guarantees very high energy for tight and controlled bass reproduction and perfect thermal stability with minimum power compression.

The magnetic circuit features a special air ventilation to reduce air compression, air noises and minimize distortion in large excursion situations. The MYTHO 6 is equipped with two separate amplifiers: 200 W for the low frequencies and 100 W for the high. The design is a classic AB circuit, unparalleled for low distortion and natural sound. The signal processing is executed from a dedicated high quality DSP processing. It features a solid aluminium cabinet internally braced and reinforced to improve low frequencies behaviour and reduce resonances.

DM-2100: 2.1-ch Speaker System Features The DM-2100 2.1-ch Speaker System is an affordable way to add accurate reference monitoring with a subwoofer for enhanced bass response. The left and right speakers each offer 15 watts of power, while the 50-watt subwoofer provides a powerful low-end boost. And with 24-bit/96kHz digital inputs, the DM-2100 is perfect for use with Roland/BOSS digital studios and instruments, or with computer systems and more.

• Affordable 2.1-channel monitoring system with 24-bit/96kHz digital inputs
• Powered bass reflex speakers with 15 watts per side and flat frequency response
• Active subwoofer with 50-watt amplifier for increased low end
• Front-mounted controls convenient located on right speaker
• Coaxial and optical digital inputs, plus analog inputs (RCA and 1/4-inch type)
• Sleek black wooden cabinets with magnetic shielding