When it comes to power amps, it?s all about power, reliability and price. Thankfully, TAPCO?s J?1400?delivers on all fronts. In developing these amps, we devised a rigorous power amp test which was literally un-passable by dozens of name-brand amps on the market today. Our new Juice Series passed the test with flying colors. It?s pure […]
When it comes to power amps, it?s all about power, reliability and price. Thankfully, TAPCO?s J?1400?delivers on all fronts. In developing these amps, we devised a rigorous power amp test which was literally un-passable by dozens of name-brand amps on the market today. Our new Juice Series passed the test with flying colors. It?s pure premium. Midrange and highs are clean and dynamic. Bass is tight, clean and has the authority one would expect from larger, more expensive power amps.
Specifications
Continuous Sine Wave Average Output Power per channel, both channels driven, 20 Hz to 20 kHz
* 2 ohms: 800 W * 4 ohms: 450 W * 8 ohms: 310W
Bridged Mono Operation, 20 Hz to 20 kHz
* 4 ohms: 1400 W * 8 ohms: 900 W Note: Power ratings are specified at 120 VAC line voltage.
Power Bandwidth * 5 Hz to 50 kHz (+0, -3 dB)
Frequency Response
25 Hz to 25 kHz (+0, -1 dB)
Distortion
* THD and SMPTE IMD; 20Hz to 20kHz < 0.03% @ 8 ohms
Signal-to-Noise Ratio
* 100 dB below rated power into 4 ohms
Channel Separation
* 90 dB @ 1 kHz
Damping Factor
* 300 @ 1 kHz and below
Input Impedance
* 20 kO balanced * 10 kO unbalanced Input Sensitivity
* 1.15 V (+3.4 dBu) for rated power into 4 ohms
Gain
* 32 dB
Maximum Input Level
* 9.75 Vrms (+22 dBu)
Turn On Delay
* 2.5 seconds
Subsonic Filter
* 9 dB @ 30 Hz
Topology
* Class AB
Cooling
* Dual variable-speed fans with back to front airflow
Indicators
* Channels A and B SIG (Signal Present), OL (Overload) POWER Current Consumption
* Idle 0.5 A * Musical Program 5.1 A * Musical Program 6.7 A * Musical Program 10.6 A AC Power Requirements
* U.S. 120 VAC, 60 Hz * Europe 240 VAC, 50 Hz * Japan 100 VAC, 50/60 HzKorea 220 VAC, 60 Hz
Physical Dimensions and Weight
* Height: 3.5 in/89 mm * Width: 19.0 in/483 mm * Depth: 15.7 in/400 mm * weight: 48.5 lb/22.0 kg Features
* J?1400 1400W @ 4 Ohms bridged * Easily switchable mono/stereo/bridged mono operating modes * Separate Speakon? outputs for Channel A and Channel B * Third Speakon output for mono bridged applications: also provides both output channels on a single NL4 connector * 30Hz subsonic filter for low-frequency speaker protection * Handles for easy transport and protection of level controls * Defeatable clip limiter * Front-panel signal and overload indication
Weight
22.00 kg
Reviews
There are no reviews yet.
Be the first to review “TAPCO J2500 – Big power amp-2x750W-4 Ohms” Cancel reply
When it comes to power amps, it?s all about power, reliability and price. Thankfully, TAPCO?s J?1400?delivers on all fronts. In developing these amps, we devised a rigorous power amp test which was literally un-passable by dozens of name-brand amps on the market today. Our new Juice Series passed the test with flying colors. It?s pure premium. Midrange and highs are clean and dynamic. Bass is tight, clean and has the authority one would expect from larger, more expensive power amps.
Specifications
Continuous Sine Wave Average Output Power per channel, both channels driven, 20 Hz to 20 kHz
* 2 ohms: 800 W * 4 ohms: 450 W * 8 ohms: 310W
Bridged Mono Operation, 20 Hz to 20 kHz
* 4 ohms: 1400 W * 8 ohms: 900 W Note: Power ratings are specified at 120 VAC line voltage.
Power Bandwidth * 5 Hz to 50 kHz (+0, -3 dB)
Frequency Response
25 Hz to 25 kHz (+0, -1 dB)
Distortion
* THD and SMPTE IMD; 20Hz to 20kHz < 0.03% @ 8 ohms
Signal-to-Noise Ratio
* 100 dB below rated power into 4 ohms
Channel Separation
* 90 dB @ 1 kHz
Damping Factor
* 300 @ 1 kHz and below
Input Impedance
* 20 kO balanced * 10 kO unbalanced Input Sensitivity
* 1.15 V (+3.4 dBu) for rated power into 4 ohms
Gain
* 32 dB
Maximum Input Level
* 9.75 Vrms (+22 dBu)
Turn On Delay
* 2.5 seconds
Subsonic Filter
* 9 dB @ 30 Hz
Topology
* Class AB
Cooling
* Dual variable-speed fans with back to front airflow
Indicators
* Channels A and B SIG (Signal Present), OL (Overload) POWER Current Consumption
* Idle 0.5 A * Musical Program 5.1 A * Musical Program 6.7 A * Musical Program 10.6 A AC Power Requirements
* U.S. 120 VAC, 60 Hz * Europe 240 VAC, 50 Hz * Japan 100 VAC, 50/60 HzKorea 220 VAC, 60 Hz
Physical Dimensions and Weight
* Height: 3.5 in/89 mm * Width: 19.0 in/483 mm * Depth: 15.7 in/400 mm * weight: 48.5 lb/22.0 kg Features
* J?1400 1400W @ 4 Ohms bridged * Easily switchable mono/stereo/bridged mono operating modes * Separate Speakon? outputs for Channel A and Channel B * Third Speakon output for mono bridged applications: also provides both output channels on a single NL4 connector * 30Hz subsonic filter for low-frequency speaker protection * Handles for easy transport and protection of level controls * Defeatable clip limiter * Front-panel signal and overload indication
Phonic\'s MAX 2500 Power Amplifier provides 1500 Watts of power at 8 ohms (bridge mono) or 750 Watts at 4 ohms (stereo)- ideal for medium to large-size clubs, churches, auditoriums and more. Input to the MAX 2500 amp is achieved via combo connectors that accept both XLR and 1/4\' jacks, and output is achieved through either Speakon?-type connectors or binding posts. The MAX 2500 features ground switches, user defeatable clip limiters, selectable high pass filters, and the option to choose between stereo, parallel and bridge operating modes, making this amplifier ideal for real world application.
Signal and Peak LED indicators to monitor performance
Short circuit, thermal, subsonic, RF protection, output DC offset
Power on/off muting
L1800 600W-600W 4ohm (360W-360W 8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation.
This professional stereo power amplifier, working in class-H mode, provides 2x800W, at an efficiency of around 85%.
A passive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode. The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling. The integral soft clip limiter protects against damage to the connected loudspeakers. The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS
Power output stereo 2Ω:
2 x 800 Watt rms
Power output stereo 4Ω:
2 x 650 Watt rms
Power output stereo 8Ω:
2 x 350 Watt rms
Power output bridged 4Ω:
1600 Watt rms
Power output bridged 8Ω:
1300 Watt rms
Frequency Response:
20 Hz ÷ 20 kHz
Signal/noise rate:
> 103 dB
Crosstalk:
> 70 dB
Distortion (THD+N):
Intermodulation:
Damping factor:
200:1 (8 Ω)
Slew rate:
50 V/μS
INPUT SECTION
Input connector:
2 x XLR balanced, 6,3mm jack unbalanced
Input sensitivity:
0 / 0.775 dBm/V RMS
Input impedance:
20.000 kΩ
Controls:
Volume control for each channel
OUTPUT SECTION
Output connector:
2 x Neutrik Speakon 4 ways
SYSTEM PARAMETERS
Cooling:
Two-speed fan
Protections:
Temperature, DC, RFI short circuit, Soft-Start, Thermal on transformer
POWER REQUIREMENT
Operating voltage:
220÷240 / 110÷120 ~ 50 / 60 V ~ Hz
Max.current:
7.5 A
Power Consumption:
2700 W
PHYSICAL SPECIFICATIONS
Height:
88 / 3.46 mm/inch
Width:
483 / 19.01 mm/inch
Depth:
455 / 17.91 mm/inch
Net Weight:
19.5 / 42.98 Kg/Lbs
SHIPPING INFORMATION
Package height:
150 / 5.9 mm/inch
Package width:
555 / 21.85 mm/inch
Package depth:
525 / 20.66 mm/inch
Shipping Weight:
20 / 44.09 Kg/Lbs
Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 1800 W, 4 Ω - 1200 W, 8 Ω - 750 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 3400 W, 4 Ω - 1800 W, 8 Ω - 950 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 3600 W, 8 Ω - 2400 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +6.6 dBu (1.66 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class H Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 17.7 kg (39.0 lbs)
- Power levels matched to the most popular speakers used by entertainers - Optimized for maximum real-world headroom into 4 ohm and 8 ohm speaker systems - Inputs: XLR, 1/4" TRS and phono input connectors for compatibility with any source - Outputs: Speakon(R) combo accepts, 1/4" (TS) plugs or Speakon 2-pole and 4-pole plugs (connects 2 poles only). Binding posts support all other speaker wiring systems - Minimum depth chassis (10.1“/257 mm) fits in compact, inexpensive effects racks - Lightweight - GX7 is only 15.5 lbs (7 kg) - Detented gain controls for precise setting and matching of sensitivity - GuardRail(TM) automatically protects the amplifier and loudspeakers from damage due to temperature rise or overdrive without shutting down the show - Front panel LEDs monitor Power, Signal and Clipping - Subwoofer/Satellite crossover built-in - 230V 16.5 lbs (7.5 kg)
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.