TOA M-9000 DIGITAL MATRIX MIXER

Ψηφιακός μίκτης - επεξεργαστής matrix. Δέχεται έως 8 mic/line inputs και 8 εξόδους. Διαθέτει DSP και επιτρέπει τηλεφωνικό Paging. Υπάρχει δυνατότητα αυτόματου ελέγχου στάθμης εκπομπής σύμφωνα με τον θόρυβο περιβάλλοντος. Συναργάζεται με Η/Υ για τον προγραμματισμό και τη ρύθμισή του. Κατάλληλο για εγκαταστάσεις σε Meeting rooms, Εκκλησίες, συνεδριακές αίθουσες, restaurant κλπ.

The ZonePRO 1261m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.

The 1261m features a total of 12 inputs and six outputs. Inputs include six balanced mic/line switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one S/PDIF input for up to two digital channels. Hardware-controlled
microphone gain allows adjustment of microphone gain per channel.

The 1261m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth®, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.

A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.

The front panel of the 1261m features a power status LED, a network traffic LED, and an RS-232 control port.

Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.

All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information).

ZonePRO Designer—the configuration, control and monitoring software for the ZonePRO family of devices—offers control of the ZonePRO 1261m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-bystep configuration process of the 1261m.

SPECIFICATIONS:

Per Output:6 Independent Six-Segment Lightpipe Output Meters that range from -30 to +20 dBu, Threshold Meters

Other:LCD Display provides information about Source Selection, Page Steering, Zone Volume and Mute

12 Total - (6) Balanced Mic/Line Inputs, (4) Unbalanced, Mono-Summed RCA Input Pairs, S/PDIF Input

Type:Euroblock (Mic/Line), RCA (Source)

Impedance (Euroblock):>50kΩ Balanced, >25kΩ Unbalanced, RF Filtered

Impedance (RCA):>25kΩ Unbalanced, RF Filtered

Max. Input Line Level:+20dBu Mic/Line, +12dBu RCA

CMRR:> 40dB, typically >55db @ 1kHz

Mic Pre Gain:30 to 60dB

Mic Input Noise (E.I.N.):< -118dBu, 22Hz-22kHz, 150Ω Source Impedance

Mic Phantom Power:+15VDC

Number of Outputs: 6 Total

Type:Electronically Balanced, RF Filtered Euroblock

Impedance:120Ω Balanced, 60Ω Unbalanced

Max. Output Level:+20dBu

Type: dbx Type IV™ Conversion System

Dynamic Range line: >113dB, A-weighted, >110dB unweighted

Type IV dynamic range:
>119dB, A-weighted, 22kHz
BW: >117dB, unweighted, 22kHz BW

Sample Rate: 48kHz

Dynamic Range: 112dB A-weighted, 109dB unweighted, 22kHz BW

Dynamic Range: >110dB A-weighted, >107dB unweighted, 22kHz BW

THD+N: 0.003% typical at +4dBu, 1kHz, 0dB gain

Frequency Response: 20Hz – 20kHz, +/- 0.5dB

Interchannel Crosstalk: >80dB typical

Crosstalk input to
output: >80dB

Propagation Delay 0.8 msec

Operating Voltage: 100-240 VAC, 50/60Hz

Power Consumption: 27 Watts

BTU:

Analog Inputs    Modular
Analog Outputs    Modular
Audio Network    CobraNet CM-1 Module (optional)
Cooling    Left-to-right, 3-stage fan
Data Format    24 Bit linear A/D and D/A conversion, 48 Bit processing
Digital Inputs    Modular
Digital Outputs    Modular
FIR-Drive    Yes
GPIO Control Port    2 x 6-pole Euro block4 Control Inputs (analog 0 - 10 V / logic control) 3 Control Outputs (Relay contact to ground) 1 Fault Output (NC Relay contact)3 Reference Outputs (+5 V / +10 V/ GND)
Internal Processing    2 DSPs Standard (150 MHz, 300 MIPS), DSP-2 Extension Module (3 dual core processors-1200 MIPS total) , 1 DSP per Audio Module (100 MHz, 100 MIPS) 1500 MIPS total without I/O cards
Network Control (IRIS-Net)    Yes
Network Interface    Ethernet-10/100 MBit/s, RJ-45
Power Consumption    90 W max. (incl. 2 x AI-1, 2 x AO-1, 1 x CM-1 modules)
Power Supply    100 - 240 VAC, 50/60 Hz
Sample Rate    48 kHz internal
Serial Interface    2 Ports, 9pin D-Sub female (Remote Control)
Signal-to-Noise Ratio (A-weighted)    115 dB
Total Harmonic Distortion    0.01 %
Height    2RU 88.1 mm (3.47“)
Width    483 mm (19.02“)
Depth    381 mm (15“)
Weight Net    7.37 kg (16.25 lbs)

Intelligent Control Panel, Wall-mountable.
The ICP1 intelligent control panel features controls virtually identical to those on the DME64N/DME24N
front panels, giving operators remote control capabilities for both DMEs. It offers unmatched ease of use
thanks to a large, easy-to-read backlit LCD display that shows names for scenes and function keys in 5
languages – Japanese, English, French, German and Spanish. The 6 function keys appearing at the top
and bottom of the LCD screen can be assigned to most parameters for easy remote control access.
These function keys are defined as a "function key set" or "page“. Up to 4 sets of "pages" are available –
for up to 24 parameters assignable to function keys. Users can change the "page" by pressing the
HOME key. A single function key can be used for simultaneous multiple parameter control by defining
parameter links. Function keys are defined with DME Designer software.

The NAI48-ES is a digital audio network interface that uses the EtherSound network protocol. Digital mixing consoles such as the Yamaha PM5D, M7CL, or LS9 can be connected to AD8HR 8-channel microphone preamp/AD converter or DA824 DA converter units via the NIA48-ES for remote analog input or output interfacing on stage or wherever needed. This type of system eliminates noise problems that are unavoidable with conventional analog console plus multi-cable type setups, and dramatically reduces microphone cable length for superior sound quality. Cabling between the console and "stage box" units is also simplified for fast, easy setup.

48 channels of digital audio each way over a single Cat-5 Ethernet cable EtherSound™ Networking Uncompromising Yamaha Quality, Compatibility, and Reliability