Content |
The VM-3240E is a multifunctional amplifier that can be mounted in an EIA-Standard equipment rack (3-unit size). The unit comes with the speaker output section which has an internal attenuator and 6-output selector. In addition, the unit features the surveillance function which automatically checks the system for failures.
Power Source | 230 V AC, 50/60 Hz | Power Consumption | 600 W (with rated output signal), 260 W (according to EN60065) | Rated Output | 240 W | Frequency Response | 50 Hz - 20 kHz, ±3 dB (at 1/3 rated output) | Distortion | 0.7 % or less (at rated output, 1 kHz) | S/N Ratio | 85 dB or more | Input | External amplifier input: 100 V line, removable terminal block (14 pins) | Output | Speaker output 1 - 2: Max. (240 W) per output
Speaker output 3 - 6: Max. (120 W) per output
Speaker output 1 - 6: Total within 240 W, removable terminal block (14 pins)
Allowable minimum load: 500 Ω (20 W) at 100 V line for speaker line failure detection
Direct output: Direct output from internal or external amplifier,
removable terminal block (16 pins) | VM Link | Input: Connecting the VM-3240VA or VM-3360VA, RJ45 female connector
Output: Connecting the VM-3240E or VM-3360E, RJ45 female connector
Maximum distance: 800 m (874.89 yd)
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | EXT PA Link | Connecting the VP-2241, RJ45 female connector
Maximum distance: 5 m (16.4 ft)
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | General Control | Input 1 - 8: No-Voltage make contact input, open voltage: 24 V DC,
short-circuit current: 2 mA or less, removable terminal block (14 pins)
Output 1 - 8: Isolated open collector output, withstand voltage: 30 V DC,
operating current: 10 mA or less, removable terminal block (14 pins) | Emergency Control | Input 1 - 5: No-Voltage make contact input, open voltage: 24 V DC,
short-circuit current: 2 mA or less, RJ45 female connector
Input 6: Isolated voltage input, Inactive: -24 V ±20 %, Active: +24 V ±20 %,
RJ45 female connector
Status out: Relay contact output, withstand voltage: 40 V DC,
operating current: 2 - 300 mA, RJ45 female connector | ATT Control | Relay contact 1-6, 125 V AC or 30 V DC, total under 5 A,
removable terminal block (16 pins) | Power Input/Output | Power in: Connecting the VX-2000DS only (operating range: 20 - 40 V DC)
PS out: 28 V DC/18 A
M4 screw terminal, distance between barriers: 11 mm (0.43“) | DC24V Output | 24 V DC, Maximum feeding current 0.3 A | Ds Link | Connecting the VX-2000DS, RJ45 female connector
Maximum distance: 5 m (16.4 ft)
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | Operating Temperature | -5 ℃ to +45 ℃ (23 ゜F to 113 ゜F) | Operating Humidity | 5 % to 95 %RH (no condensation) | Finish | Panel: Aluminum, hairline, black
Case: Surface-treated steel plate, black, paint | Dimensions | 482 (W) × 132.6 (H) × 407 (D) mm (18.98" × 5.22" × 16.02“) | Weight | 16.5 kg (36.38 lb) | Accessory | Power cable (2 m (6.56 ft)) …1, Link cable (3 m (9.84 ft)) …2,
Plastic foot …4, Plastic foot mounting screw …4,
Removable terminal plug (14 pins) …3, Removable terminal plug (16 pins) …1 |
|
The Crown 135MA is a high value mixer-amplifier for commercial audio. It provides 8-ohm and constant-voltage outputs (70V and 100V). Typical uses are paging, background music, and music-on-hold. The 135MA provides 3 inputs (each with a volume control) and a 35W amplifier output. Other features include priority muting, voice activated muting, phantom power, and Bass and Treble controls.
Features
- 3 inputs (each with a volume control), and one 35W amplifier output channel
- Ideal for paging, background music, and music-on-hold
- Balanced Phoenix-type mic/line input, telephone output, dual RCA stereo music inputs, screw-terminal speaker outputs
- Priority muting by VOX or external switch
- Bass and Treble controls on master output
- Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
Specifications
- Minimum Guaranteed Power into 8 ohms or 70V/100V Output: 35W
- Frequency Response (at 1 watt from line out): 50Hz to 20kHz +/-1dB; 19Hz to 34kHz +0, -3dB
- Signal to Noise Ratio (ref. to rated power, master volume at minimum):
Mic: > 58 dB.
Line: > 60 dB.
Telephone: > 60 dB.
Inputs 2 or 3 (and 4 in 160MA): > 78 dB - THD+N:
|
| - MODULAR DESIGN Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-120A/340A/480Aʼs audio capabilities. - INDIVIDUAL INPUT GAIN CONTROLS Rear-panel gain controls for each input channel for total control of individual levels. - SPEAKER SELECT Six speaker select switches enable you to select any combination of up to five speakers. - SELECTABLE PRIORITY MUTING Switchable audio signal priority for Channels 1 and 2, Chime and Telephone input over other input sources. - REMOTE CONTROL INPUT (only PAM-340A/480A) Individual speaker zones can be selected and chime can be operated by wired remote control. - ANNOUNCEMENT CHIME Convenient four-tone chime for use with announcements. - EM(EMERGENCY) - OPTIONAL EMERGENCY VOICE IC (only PAM-340A/480A) When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted. | | | | | | | Rated Output Power | PAM-120A(THD 1%) : 120W (RMS) PAM-340A(THD 3%) : 340W (RMS) PAM-480A(THD 3%) : 480W (RMS) | Frequency Response | Amp In | 80Hz~20kHz | Link In | 80Hz~15kHz | CH1~CH6 | 120Hz~8kHz | Remote In | 120Hz~8kHz(PAM-340A, PAM-480A) | T.H.D.(at 1kHz Rated Output) | Less than 1%(PAM-120A) | T.H.D.(at 1kHz Half Power Output) | Less than 0.5%(PAM-340A, PAM-480A) | S/N | Amp In | Better than 90dB(PAM-120A) Better than 88dB(PAM-340A/480A) | Link In | Better than 65dB | CH1~CH6 | Better than 50dB | Remote In | Better than 50dB(PAM-340A/480A) | Input Sensitivity/Impedance | CH1~CH6 | TRIM VR -60dB Position | 1mV/10kΩ | TRIM VR -16dB Position | 158mV/10kΩ | Link In | 100mV/10kΩ | Amp In | 1V/47kΩ(PAM-120A) 1V/20kΩ(PAM-340A/480A) | Remote In | 1V/10KΩ(PAM-340A/480A) | Speaker Output/Impedance | PAM-120A : 120W/4Ω, 70V/42Ω, 100V/83Ω PAM-340A : 340W, 100V/29.4Ω PAM-480A : 480W, 100V/20.8Ω | Preamp Output/Impedance | 1V/600Ω | Tone Control (100Hz, 10kHz) | ±12dB | CH1~CH6 EQ Control (100Hz, 1kHz, 10kHz) | ±12dB | | | | | Power Source | 100–120VAC or 220V–240VAC; 50/60Hz, 24V DC(only PAM-120A) | | (Supplied AC mains transformer depends on country requirements) | Power Consumption | PAM-120A : 135W(1/8 POWER), 200W(1/3 POWER), 300W(FULL POWER) PAM-340A : 260W(1/8 POWER), 400W(1/3 POWER), 620W(FULL POWER) PAM-480A : 360W(1/8 POWER), 550W(1/3 POWER), 880W(FULL POWER) | Weight | PAM-120A : 13kg/28.7lb PAM-340A : 13.5kg/29.7lb PAM-480A : 15.5kg/34.2lb | Dimensions | 420(W) x 132(H) x 360(D)mm/16.5(W) x 5.2(H) x 14.2(D)in | Operation Temperature | 14F~104F (-10°C~+40°C) | ※ Specifications and design subject to change without notice. | | | |
|
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
Specification |
| Power Source | 220 - 240V AC or 24V DC | Rated Output | 30W | Power Consumption | 34W (EN60065), 78W(AC operation at rated output, 2A (DC operation at rated output) | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | Distortion | Under 1% at 1kHz,1/3 rated power | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:330W (100V)
LOW IMPEDANCE: 4Ω (11V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | Phnatom Powe | DC + 21V (MIC 1) | S/N Ratio | Over 60dB | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | Indicator | Power signal, peak | Finish | Panel: ABS resin, black/Case: Steel plate, black | Dimensions | 420 (W) x 100.9 (H) x 280.2 (D) mm | Weight | 5kg |
|
XV Series - Intelligent Power Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 1600: 2x 800 W / 100 V Class: AB Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans(temp. reg. variable speed) Weight: 39 kg Dimensions: 3 RU / 483 x 88 x 382 mm(19" x 3.5" x 15 |
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 400: 2x 200 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 17 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Reviews
There are no reviews yet.