Content |
The VM-3360E is a multifunctional amplifier that can be mounted in an EIA-Standard equipment rack (3-unit size). The unit comes with the speaker output section which has an internal attenuator and 6-output selector. In addition, the unit features the surveillance function which automatically checks the system for failures.
Power Source | 230 V AC, 50/60 Hz | Power Consumption | 850 W (with rated output signal), 380 W (according to EN60065) | Rated Output | 360 W | Frequency Response | 50 Hz - 20 kHz, ±3 dB (at 1/3 rated output) | Distortion | 0.7 % or less (at rated output, 1 kHz) | S/N Ratio | 85 dB or more | Input | External amplifier input: 100 V line, removable terminal block (14 pins) | Output | Speaker output 1 - 2: Max. (360 W) per output
Speaker output 3 - 6: Max. (120 W) per output
Speaker output 1 - 6: Total within 360 W, removable terminal block (14 pins)
Allowable minimum load: 500 Ω (20 W) at 100 V line for speaker line failure detection
Direct output: Direct output from internal or external amplifier,
removable terminal block (16 pins) | VM Link | Input: Connecting the VM-3240VA or VM-3360VA, RJ45 female connector
Output: Connecting the VM-3240E or VM-3360E, RJ45 female connector
Maximum distance: 800 m (874.89 yd)
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | EXT PA Link | Connecting the VP-2421, RJ45 female connector
Maximum distance: 5 m (16.4 ft)
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | General Control | Input 1 - 8: No-Voltage make contact input, open voltage: 24 V DC,
short-circuit current: 2 mA or less, removable terminal block (14 pins)
Output 1 - 8: Isolated open collector output, withstand voltage: 30 V DC,
operating current: 10 mA or less, removable terminal block (14 pins) | Emergency Control | Input 1 - 5: No-Voltage make contact input, open voltage: 24 V DC,
short-circuit current: 2 mA or less, RJ45 female connector
Input 6: Isolated voltage input, Inactive: -24 V ±20 %, Active: +24 V ±20 %,
RJ45 female connector
Status out: Relay contact output, withstand voltage: 40 V DC,
operating current: 2 - 300 mA, RJ45 female connector | ATT Control | Relay contact 1-6, 125 V AC or 30 V DC, total under 5 A,
removable terminal block (16 pins) | Power Input/Output | Power in: Connecting the VX-2000DS only (operating range: 20 - 40 V DC)
PS out: 28 V DC/24 A
M4 screw terminal, distance between barriers: 11 mm (0.43“) | DC24V Output | 24 V DC, Maximum feeding current 0.3 A | Ds Link | Connecting the VX-2000DS, RJ45 female connector
Maximum distance: 5 m (16.4 ft)
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | Operating Temperature | -5 ℃ to +45 ℃ (23 ゜F to 113 ゜F) | Operating Humidity | 5 % to 95 %RH (no condensation) | Finish | Panel: Aluminum, hairline, black
Case: Surface-treated steel plate, black, paint | Dimensions | 482 (W) × 132.6 (H) × 407 (D) mm (18.98" × 5.22" × 16.02“) | Weight | 19 kg (41.89 lb) | Accessory | Power cable (2 m (6.56 ft)) …1, Link cable (3 m (9.84 ft)) …2,
Plastic foot …4, Plastic foot mounting screw …4,
Removable terminal plug (14 pins) …3, Removable terminal plug (16 pins) …1 |
|
Multi-purpose, multi-function mixer/power amplifiers specifically designed for maximum versatility and cost-effective high-performance are ideal units for any PA requirement in locations such as schools and offices and other intermediate size environments. A choice of different power outputs are offered as well as functions such as paging and dual zone coverage.
Specification | |
Power Source |
AC mains 50/60Hz, or 24V DC (M4 screw terminal) |
Output |
120W |
Power Consumption |
AC operation: 158W (rated output), 66W (EN60065) 24V DC operation: 7.0A (rated output), 2.8A (EN60065) |
Frequency Response |
50 - 20,000Hz ±3dB |
Distortion |
Under 2% at 1kHz, rated power |
Input |
MIC 1: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack DIN socket (5 pins) MIC 2, 3: -60dB(*1), 600Ω, electronically-balanced, combined type of XLR-3-31 Equivalent and phone jack AUX 1(MOH): -20dB*, 10kΩ, unbalanced RCA pin jack AUX 2: -20dB(*1), 10kΩ, unbalanced, RCA pin jack AUX 3: -20dB(*1), 10kΩ, unbalanced, RCA pin jack combined type of XLR-3-31 and phone jack TEL(*2): -20dB*1, 10kΩ, electronically-balanced, M3 screw terminal |
Output |
REC: 0dB(*1), 600Ω, unbalanced, RCA pin jack LINE 1,2(*3): 0dB(*1), 600Ω, unbalanced, RCA pin jack MOH: 0dB(*1), 600Ω transformer balanced, M3 screw terminal SPEAKER SELECTOR: 2 zone, high impedance (100V line/83Ω), individual selector switch, M4 screw terminal DIRECT SPEAKER OUT: High impedance (100V line/83Ω),M4 screw terminal Low impedance (4 - 16Ω), M4 screw terminal(Both Low and High impedance terminals cannot be used at the same time.) |
Phantom Power |
ON or OFF for each MIC 1 - 3 with switch setting |
S/N ratio (Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min) Over 76dB (Master volume: max) Over 60dB (MIC 1 - 3)) Over 76dB (AUX 1 - 3) Over 90dB (TEL) Over 96dB (EMERGENCY) |
Control Input |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz TEL: No-voltage make contact input, open voltage: 24V DC, short-circuit: under 5mA, M3 screw terminal EMERGENCY (*4): No-voltage make contact input, open voltage: 24V DC, short-circuit: under 10mA, M3 screw terminal |
Control Output |
Power remote: Open collector output, withstand voltage: 35V DC, control current: under 50mA, M3 screw terminal |
Indicator |
5 point LED output level meter, Power indicator LED, Zone indicator LED, Emergency LED, TEL LED |
Priority |
EMERGENCY: Overrides other inputs TEL: Overrides other inputs except "EMERGENCY”, ON/OFF selectable with switch setting MIC 1: Overrides other inputs except "EMERGENCY & TEL”, ON/OFF selectable with switch setting |
Operating Temperature |
-10ºC - +40ºC |
Finish |
Panel: ABS resin, black, hair line Case: Steel plate, black |
Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
Weight |
12.6kg |
Accessory |
Power cord x 1, Terminal block cover x 1, Terminal block cover mounting screw x 2 |
Option |
Rack mounting bracket: MB-25B, Volume control cover: YA-920, Input transformer: IT-453A |
Note* |
(*1) 0dB = 1V (*2) Can be transformer-balanced with the addition of optional IT-453A input transformer. (*3) LINE 1 and LINE 2 outputs can be interlocked with ZONE 1 and ZONE 2 speaker selectors, respectively. (This function needs internal modification.) (*4)Operation when activated can be selected from the following: Turning ON the unit\'s power (factory-preset) or OFF. (The OFF function needs internal modification.) |
|
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 400: 2x 200 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 17 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
The Crown® 160MA is a high-value mixer-amplifier for commercial audio. It provides 8-ohm and constant-voltage outputs (70V and 100V). Typical uses are paging, background music, and music-on-hold. The 160MA provides 4 inputs (each with a volume control) and a 60W amplifier output. Other features include priority muting, voice activated muting, phantom power, and Bass and Treble controls.
FEATURES
- 4 inputs (each with a volume control), and one 60W amplifier output channel
- Ideal for paging, background music, and music-on-hold
- Balanced Phoenix-type mic/line input, telephone output, dual RCA stereo music inputs, screw-terminal speaker outputs
- Priority muting by VOX or external switch
- Bass and Treble controls on master output
- Three-Year, No-Fault, Fully Transferable
- Warranty completely protects your investment and guarantees its specifications
|
| - SPEAKER SELECT(5ZONE SPEAKER OUTPUT) Six speaker select switches enable you to select any combination of up to five speakers. - SELECTABLE PRIORITY MUTING Switchable audio signal priority for MIC Channels 1, siren, Chime and Telephone input over other input sources. - MONITOR SPEAKER You can monitor output signal by using the monitor speaker, and can control the monitor level on front panel by 3 step lever switch. - ANNOUNCEMENT CHIME Convenient four-tone chime for use with announcements. - REMOTE CONTROL INPUT Individual speaker zones can be selected and chime can be operated by wired remote control. - EM(EMERGENCY) When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted. - REMOTE POWER You can turn on/off amplifier by remote control. - INDIVIDUAL INPUT GAIN CONTROLS Rear-panel gain controls for each input channel for total control of individual levels. - MODULAR DESIGN Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-510/520ʼs audio capabilities. ACCESSORIES One detachable AC power cord is provided for use with this product. | | | | | | PAM-510 | PAM-520 | Amplifier Section (Amp In@1kHz, 4Ω Load Output) | Rated Output Power (THD 1%) | 120W(RMS) | 240W(RMS) | Speaker Zone 1~5 Output | 25W MAX | 50W MAX | Input Sensitivity/Impedance | 1V/20kΩ | S/N | Better than 85dB | Frequency Response (at 1kHz Half Power Output, ±3dB) | 80Hz~18kHz | Mic Input Section (Mic 1~4 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –60dBV/600Ω | S/N | Better than 55dB | Frequency Response (±3dB) | 120Hz~10kHz | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | Phantom Power | +24VDC | Line Input Section (Line 1~2 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –30dBV/10kΩ | S/N | Better than 65dB | Frequency Response (±3dB) | 80Hz~15kHz | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | Remote Amp Section (Remote In@1kHz, Preamp Out) | Mic Input Sensitivity/Impedance | –60dBV/600Ω | S/N | Better than 55dB | Frequency Response (±3dB) | 120Hz~10kHz | Tel In Section (Tel In@1kHz, Preamp Out) | Input Sensitivity/Impedance | 0.3V/600Ω(USA/Canada) | 0.775V/600Ω(EC & Associated) | S/N | Better than 65dB | Frequency Response (±3dB) | 330Hz~3kHz | Pre Amp Out(Mic 1~4, Line 1~2, Tel In, Remote In) | 0dBV/600Ω | | T.H.D | Less than 0.5% | Record Out | –10dBV/3kΩ | Operating Temperature | –10°C~40°C | Power Source | 100–120VAC or 220–240VAC; 50/60Hz, 24VDC | Power Consumption (1/8 POWER) | 180W | 320W | Weight | 17kg/37.6lb | 19kg/42lb | Dimensions | 482(W) x 132(H) x 398(D)mm 19(W) x 5.2(H) x 15.7(D)in | ※ Specifications and design subject to change without notice. | | | |
|
| - INTEGRATED DIGITAL PA COMBINATION SYSTEM (ALL IN ONE SYSTEM) - SIMULTANEOUS 2 GROUP DIFFERENT BROADCASTING - DIGITAL PROCESSING & DIGITAL AMPLIFIER - CD COPY (EXTEND LIFE-TIME OF CD MECHANISM) - USB INTERFACE (USB HOST) | | | | | POWER AMP | Rated Output | 120W + 120W | Input Sensitivity | -10dBV / 10kΩ | S/N | Better than 75dB | Frequency Response | 100Hz-18kHz | MIC/LINE 1~5CH | MIC Input Sensitivity | -55dBV / 10kΩ | MIC S/N | Better than 55dB | MIC Frequency Response | 120Hz-10kHz | MIC T.H.D | Less than 0.5% | LINE Input Sensitivity | -10dBV / 10kΩ | LINE S/N | Better than 65dB | LINE T.H.D | Less than 0.3% | CD | S/N | Better than 80dB | Frequency Response | 100Hz-20kHz | TUNER | S/N | Better than 60dB | Frequency Response | 120Hz-12kHz | Power Consumption | 170W (1/8 Power) | Weight | 16kg/35.3lb | Dimension | 482(W)x177(H)x373(D)mm/19(W)x7(H)x15(D)in | ※ Specifications and design subject to change without notice. | | | |
|
Reviews
There are no reviews yet.