TOA VP-2241 POWER AMPLIFIER 2x240W/100V

• VP-2241 (240 W-by-1 channel)
• Power Amplifier uses the VP-200VX Power Amplifier Input Module per channel.

• Specification
  Power Source	28V DC (operating range: 19 - 44V DC) M4 screw terminal, distance between barriers: 12mm
  Current Consumption	(EN60065) 4.8A
  Rated Output Power	240W
  Output Voltage/Impedance	100V/41 Ω, 70V/21ohms, 50V/10ohms selectable by the internal wiring change)
  Number of channels	1
  Input	Specified by input module VP-200VX
  Number of Module slots	4, usable module: VP-200VX
  Output	Power amplifier output (speaker line): M3.5 screw terminal, distance between barriers: 8.8mm
  Frequency response	40 - 16,000Hz, ±3dB (at 1/3 rated output)
  Distortion	Under 1% (at rated output, 1kHz)
  S/N Ratio	Over 80dB
  Panel Indicator	Channel power indicator: 1 channel, dual color LED Overheat indicator: Yellow LED
  Operating temperature	0ºC to +40ºC
  Finish	Panel: Surface-treated steel plate, black, 30% gloss, paint
  Dimensions	482 (W) x 88.4 (H) x 340.5 (D)mm
  Weight	8.1kg
  Accessory	Rack mounting screw x 4, Fiber washer x 4

XV Series - Intelligent Power  
 
Power Without Compromises.

The XV is designed for paging, music and alarm signals. Versatile,
dynamic and extremely rugged according to IEC286-3. For the
highest requirements in safety and quality.
Sequential power on, alive contacts and incorporated ground fault
detection - the XV is the solution under all conditions. Without the
need for additional equipment. For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers
in the XV series are some of the best available.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XV 1600:  2x 800 W / 100 V
Class:  AB
Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.07%
Signal-to-Noise Ratio:  < 101 dB
Channel Seperation:  > 70 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Cooling:  2 to 3 fans(temp. reg. variable speed)
Weight:   39 kg
Dimensions:  3 RU / 483 x 88 x 382 mm(19" x 3.5" x 15

P-120D features 2x 200W into 4 Ohm load. This amplifier matches the needs for noiseless operation through air-cooling. It is ideally suitable in studios, small theatres, cabarets, churches, conference- and multimedia rooms etc. Multiple protection circuits care for stable operation. The amplifier is rackmountable (2 units). The optional transformer LT-101 converts the input to a balanced transformer isolated input.

Crown CDi 2000 2x800W-4Ω Power Amplifier

The Crown? CDi 2000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply.
The outputs shall be usable as dual or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker. Dual connectors shall work with 2-8 ohm or
70V loads. Bridge-mono connectors shall work with 4-8 ohm or 140V loads.
HiQnet USB Connector: Type B, connects to a USB port on a PC.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Dual (per channel): 1,000W with 1% THD, 4 ohm Dual
(per channel): 800W, 8 ohm Dual (per channel) 475W, 4 ohm Bridge-Mono:
2,000W with 1% THD, 8 ohm Bridge-Mono: 1,600W, 70V Dual (per channel):
800W.
Voltage Gain at 1kHz, 8 ohm rated output: 32.9 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Dual
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity: 1.4V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 100 dB (A
weighted).
Damping Factor: Better than 500 from 20 Hz to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.9A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave and Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB
bandpass gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 20 presets. 19 are user-defi nable.
Protection shall include the following:
CDi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg).
The amplifier shall be designated the Crown CDi 2000.

• Easy installation in practically any 12V battery equipped car.
• Compact, rugged construction and front panel controls.
• Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
• Unidirectional dynamic microphone with talk switch.