| Content | Original TONAR stylus 794 DS
For Audio Technica Cartridges AT-13E that later evolved into the AT-13Ea, the AT-13EaV, AT-132EP, and the At-13EaXC High Quality Stylus Spherical Diamond for Turntable
Specs:
- Spherical Diamond Tip 0.7 mil
- Tracking Force: 1.2 – 2.5 grams tracking pressure
- Stylus Color: Red
- Made Japan
For Cartridges:
For Needles: Stylus - fits also for RS-180, ATN-102EP, ATN-122EP, ATN13EA , ATN13EAV, ATN13EAX, ATN14EA, ATN14EAV, ATN15, ATN20, STA-1-SD
Fits the following Turntables models: Thompson ATN-13 EA, ATN-132EP , Radio Shack Realistic RT-1500, ATP-N8
Note: This needle was installed on the following turntable models when they were sold.
If the original cartridge has been replaced with a different type, this needle won’t fit.
Match your old needle to the picture before you make a purchase.
| DJ S Replacement stylus
DJ S is a solid-built cartridge in a blue nylon material. It has a fine spherical stylus and a special developed and extremely balanced cantilever that provides outstanding rigidity.
Not only does the cartridge have a most sufficient tracking ability, it is also nearly unbreakable and provides the DJs with the most needed stringency. Furthermore, it equals very low record wear, an advantage for busy DJ. The DJ series has been known to many as the "jack of all trades," with improved tracking, alongside of accurate sound reproduction. Featuring a low wear stylus design, the DJ provides excellent groove handling, even with less weight applied.
The DJ series of cartridges are great for any style of music, and has been a favored choice of DJs around the world!
DJ S Stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 2 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-18.000 Hz 3dB/-2dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 9 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 2,0-4,0 g (20-40 mN)
Tracking force recommended - 3,0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Cartridge weight - 18,5 g
Compatible with cartridges - DJ S |
Genuine Original Stylus for OM 20, OM 20 Super, OMP20, LM 20, Concorde 20, TM 20
Nude Elliptical
|
Ortofon 14 Stylus Technical Data
Frequency range 20-22.000 Hz
Frequency response 20-20.000 Hz + 2 / - 2 dB
Tracking ability at 315Hz at recommended tracking force *) 70 µm
Compliance, dynamic, lateral 25 µm/mN
Stylus type Elliptical
Stylus tip radius r/R 8/18 µm
Equivalent stylus tip mass 0,5 mg
Tracking force range 1,0-1,5 g (10-15 mN)
Tracking force, recommended 1,25 g (12,5 mN)
Tracking angle 20°
Stylus colour Black
Recommended for following cartridges TM 14U |
|
Stylus 5 Spherical
| Technical data |
|
| Frequency range |
20-20.000 Hz |
| Frequency response |
20-15.000 Hz ± 2 dB
|
| Tracking ability at 315Hz at recommended tracking force *) |
60 µm |
| Compliance, dynamic, lateral |
15 µm/mN |
| Stylus type |
spherical |
| Stylus tip radius |
R/18 µm |
| Equivalent stylus tip mass |
0,5 mg |
| Tracking force range |
1,75-2,25 g (17,5-22,5 mN)
|
| Tracking force, recommended |
2 g (20 mN)
|
| Tracking angle |
20° |
| Stylus colour |
Black |
|
OM 5,OMB 5, LMA 5, SMB 5 |
*) Typical value | Ortofon 320 Stylus Technical Data
- Frequency range 20-22.000 Hz
- Frequency response 20-20.000 Hz + 2 / - 3 dB
- Tracking ability at 315Hz at recommended tracking force 70 µm
- Compliance, dynamic, lateral 25 µm/mN
- Stylus type Nude Fine Line
- Stylus tip radius r/R 8/40 µm
- Equivalent stylus tip mass 0,5 mg
- Tracking force range 1,25-17,5 g (12,5-17,5 mN)
- Tracking force, recommended 1,5 g (15 mN)
- Tracking angle 20°
- Stylus colour Grey
- Recommended for following cartridges Series 320 Universal
|
|
Reviews
There are no reviews yet.