Content |
Model T4n Product Type Power Amplifier Output Power (W) 1kHz THD+N=1% (120V) 2Ω per channel 2200 4Ω per channel 1950 8Ω per channel 1150 4Ω bridge 4400 8Ω bridge 3900 Output Power (W) 1kHz 20mS burst (120V) 2Ω per channel 2900 4Ω per channel 1950 8Ω per channel 1150 4Ω bridge 5800 8Ω bridge 3900 SN ratio (20Hz-20kHz) 106dB THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1% Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu Damping factorRL=8Ω 1kHz 800 Voltage Gain Att.max 26dB Maximum Input Voltage +24dBu Input Impedence 20kΩ (balance) 10kΩ (unbalance) Controls Specifications Front Panel POWER switch(push on/push off) attenuator (31 position) x2 Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1 Connectors Specifications Input XLR-3-31 type/ch; Euroblock connector (balance)/ch Output SPEAKON/ch, 5way biding postx1 Date Port RJ45x2 Indicators Specifications Power/Standby x1 (Green/Orange) Remote x1 (Green) Protection x1 (Red) Temp x1 (Red) heatsink temp 85°C Signal x2 (Green) Mute x2 (Red) Clip/Limit x2 (Red) Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically Cooling Variable-speed fan: x2 Power requirements 120V/60Hz Weight 14.0 kg Dimensions (W x H x D) 480 x 88 x 456mm (2U)
|
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the face
of serious power supply limitations. Refinements throughout this expanded five-model lineup make
these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Ισχύς 2 x 1050 Watt / 8Ω RMS, 2 x 1650 Watt / 4Ω RMS, 3000 Watt / 8Ω bridge RMS. Weight: 13 κιλά.
|
Number of Channels: 2
Output Power: (per channel)
8 ohms 1000W
4 ohms 1850W
2 ohms N/A
Output Power: (bridged)
8 ohms 3700W
4 ohms N/A
THD%: (@1dB below max output)
@ 1kHz |
Features - The i Series continues the Macro-Tech legacy of unparalleled sonic accuracy and detail, putting sound quality above all else
- Patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less waste
- Rugged construction ensures that all Macro-Techs are built to withstand years of abuse on the road
- Global Power Supply - designed to deliver maximum power no matter where your schedule takes you
- Studio-quality analog signal processing with built-in load, line voltage, input and output monitoring
- Standard Ethernet networking via System Architect provides integratedmonitoring and control to give system operators access to the system from anylocation
Power Output (Guaranteed minimum power in watts at 20Hz-20kHz with 0.35% THD) - 2 ohm dual (per ch), 20 mS BURST: 2,565W
- 2 ohm dual (per ch), 20Hz-20kHz: 1,800W
- 2 ohm dual (per ch), 1kHz: 1,800W
- 4 ohm dual (per ch): 2,000W
- 8 ohm dual (per ch): 1,250W
- 4 ohm bridge: 3,600W
- 8 ohm bridge: 4,000W
Performance - Frequency Response (at 1 watt, 20 Hz - 20 kHz into 8 ohms): ±0.25 dB.
- Signal to Noise Ratio below rated full-bandwidth power, A-weighted: > 108 dB.
- Total Harmonic Distortion (THD) at 1 watt into 8 ohms:
- Total Harmonic Distortion (THD) Plus Noise at full rated power:
- Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to –30 dB:
- Damping Factor (20 Hz to 100 Hz at 8 ohms): > 5000.
- Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB.
- Common Mode Rejection (CMR) (20 Hz to 1 kHz): 55 dB, typically >70 dB.
- DC Output Offset (shorted input):
- Input Impedance (nominal): 10 kilohms balanced, 5 kilohms unbalanced.
- Maximum Input Level: +20 dBu typical.
- Network: Onboard TCP/IQ and HiQnet, compatible with standard 100 Mb Ethercom hardware.
- Load Impedance: (Note: Safe with all types of loads) Stereo: 1/2/4/8/16 ohms. Bridge Mono: 2/4/8 ohms.
- Input Sensitivity (referenced to 8 ohm rated output): 1.4V, 32 dB gain, and 26 dB gain.
- Voltage Gain (referenced to 8 ohm rated output): 37.1 dB to 22.2 dB
- Required AC Mains: Universal AC input, 100-240VAC, 50/60 Hz (±15%). Maximum AC mains voltage 264VAC.
- AC Line Connector: Five cordsets supplied with amplifi er (USA, UK,European, Australia, India).
Front Panel Controls and Indicators - Bridge Mode Indicator: Amber LED illuminates when the amplifi er is set to Bridge-Mono mode.
- Ready Indicator: Red LED, one per channel. Bright red: Channel is ready to pass audio. Red: Onset of compression (thermal event or fan failure). Off: Thermal event has occurred.
- Signal Indicators: One green LED per channel. Solid green: Input signal is above –40 dBu. Bright green: Channelʼs output signal has reached the onset of audible clipping.
- Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available. The LED will fl ash when the AC line voltage is 10% above or below the nominal rated value.
- Data Indicator: Yellow LED on front panel indicates network data activity. Data indicator flashes only when the amplifier is polled for data, or is polled to see whether it is online
- Power Switch: Push-on/push-off switch with built-in green AC mains present indicator.
- Volume Control: Precision detented attenuator with 31 steps, press-and-hold mute function.
- Volume Control LED Ring: A ring of green LEDs around each volume controlshow the position of the control. Entire ring flashes when channel is muted.Can be converted to be a level meter.
Back Panel Controls, Indicators and Connectors - Power Cord Connector: Locking, detachable 20 amp IEC inlet. Voltage range is indicated above IEC inlet.
- Reset Switch/Circuit Breaker: If the current draw of the amplifier exceeds safe limits, this breaker automatically disconnects the power supply from the AC mains. The switch resets the circuit breaker.
- Output Connectors: Two high-current, 50A Neutrik® Speakon® NL4MLP (mates with NL4FC or NL4), one per channel. Ch 1 Speakon® is wired with Ch 1 and Ch 2 outputs for use with single 4-conductor cable. Two pairs of high-current, 60A color-coded 5-way binding posts (for banana plugs, spade lugs or bare wire).
- Analog Input Connectors: A 3-pin female XLR connector for each channel.
- Analog Loop Thru Connectors: Two male XLR passive analog loop through.
- Mode Switch/Indicator: Sets amplifi er to Stereo, Bridge, or Input Y mode. OFF=Stereo, YEL=Bridge, GRN=Y.
- Network Connector: This Neutrik® Ethercon connector accepts an RJ-45 connector for TCP/IQ or HiQnet networking. Next to the connector is a yellow LINK ACT indicator that shows network activity, and a green 100Mb indicator that shows a 100Mb network connection.
- Data Indicator: Yellow LED on back panel indicates network data activity. Data indicator flashes only when the amplifi er is polled for data, or is polled to see whether it is online.
- Preset Indicator: Yellow LED flashes to signal the number of the current preset if active.
- Input Sensitivity Switch: Three-position switch providing 1.4V, 32 dB, and26 dB settings for both channels.
Firmware/Software - Firmware can be updated at www.crownaudio.com > Support > Downloads.
- Software features: Same as PIP-Lite module (except no Listen Bus): UserPresets, Clip Event Monitor, Input Signal Level Monitor, Output Signal LevelMonitor, Thermal Headroom Level Monitor, Power/Standby Control, Signal Mute,Polarity Inverter, Input Signal Fader, Dynamic Gain Monitors (Ghost Faders),Amplifier Information, User and Channel Labels, Amplifier Mode, AmplifierOutput Mode, Line Voltage Monitor, Error Reporting, Auto Standby, Input SignalCompressor/Limiter, Peak Voltage Limiter, Average Power Limiter, ClipEliminator, Thermal Limiter, Limiter Tie, Load Supervision.
Construction - Cooling: Dual-zone, microprocessor controlled, continuously variable speed fans, front-to-back airflow.
- Front Panel: Cast aluminum with integrated handles.
- Dimensions (W x H x D): 19" x 3.5" x 16.2"
- Weight: 28 lbs net, 36 lbs shipping
- Protection: Amplifi er is protected against reactive loads, faults and shorts. If one channel experiences a catastrophic failure, the entire amplifier will shut down.
- Included Accessories: Rear rack ears, rack screws, operation manual, powercords, foam air filter.
|
Business amplifier 2x2000W RMS @ 4 Ohms, 2x2500W RMS @ 2h, 2x1000W @ 100V, bridged (mono) 2400W RMS @ 4 ohms, 3600W / 100V. It has inputs 3-pin XLR, jack 6,3mm (balanced), output speakon and clamp. It also has settings panel dip switches 10 posts (clip limiter, filters, stereo / parallel inputs, bridge mode). Protections turn on / off muting, triac crowbar on each channel, stable performance regardless of load. 3U / 19 "rackmount. Dimensions (HxWxD) 133x483x400mm - 33,1kg.
Characteristics
Power (Stereo Mode):
2x1050W @ 8Ohm (FTC 20Hz- 20kHz, 0,1% THD)
2x1100W @ 8Ohm (EIA 1kHz, 0,1% THD)
2x1600W @ 4Ohm (FTC 20Hz- 20kHz, 0,1% THD)
2x2000W @ 4Ohm (EIA 1kHz, 1% THD)
2x2500W @ 2Ohm (EIA 1kHz, 1% THD)
2x2500W @ 70V (EIA 1kHz, 1% THD)
2x1000W @ 100V (EIA 1kHz, 1% THD)
Power (Bridge Mode):
3200W @ 8Ohm (FTC 20Hz- 20kHz, 0,1% THD)
3600W @ 8Ohm (EIA 1kHz, 0,1% THD)
5000W @ 4Ohm (EIA 1kHz, 1% THD)
5000W @ 70V (EIA 1kHz, 1% THD)
3600W @ 100V (EIA 1kHz, 1% THD)
Signal to Noise, 20Hz-20kHz, 8Ohms:> -100dB
Input sensitivity @ 8Ohms: 1,42V (+5,3 dBu)
Voltage Gain @ 8Ohms: 64x (36dB)
Output Circuitry: 3-tier Class H
Power requirements (230V)
1/8 power pink noise at 4 ohms: 7A
1/3 power pink noise at 4 ohms: 13,5A
Distortion (SMPTE-IM): |
Power supply
- Powersoft legendary universal switch-mode power supply up to 400VAC tolerant with Power Factor Correction
- Patented output filter with ripple cancellation network
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:
- Ac protection: shut down power supply when AC mains voltage is outside the operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long term limiter: protects the loudspeaker against steady long term RMS (non-audio) signals, by reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continuous variable speed fan, front to back airflow
- Temperature forecast with LCD traced historical behavior
General
- Fixed frequency switchmode output stage for high grade sound accuracy
- Compact size – all models only 1 RU for reduced rack cost and space
- Light weight – for easier racking and shipping: 7 kg (15.4 lbs)
- Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
- Remotely switchable double input (main and aux) per channel
Loudspeaker system configuration
- Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
- Switchable 35Hz / 70Hz high pass filter per channel
- Mixed configuration with Lo-Z/Hi-Z systems possible
- Bridged mode low impedance per channel pair
Alarms and GPI/O
- NC/NO contacts per channel for alarm notifications
- Remote ON/OFF switch
- Remote VCA control per channel
Digital Signal Processing
- TI C6000 DSP platform
- AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture
- Input/output independent equalizers per channel providing PEQ, raised cosine, shelving IIR filters as well as custom output FIR filters
- Delay up to 100 ms for time alignment
- Active DampingControl™ for cable compensation
- Peak, RMS voltage, RMS current, TruePower™ limiters
Remote Control & Monitoring
Via software:
- Control and diagnostics monitoring via ArmoníaPlus
- Dedicated WebApp
Via Hardware:
- Attenuation (from 0dB to 26dB)
- High-pass filters (35Hz, 70Hz)
- Lo-Z/Hi-Z/70V/100V output selection
- Adjustable gain (from 26dB to 35 dB)
General |
Output power per Channel |
Output power per Channel |
1000 W @ 2 Ω |
800 W @ 4 Ω |
800 W @ 8 Ω |
Bridge mode |
|
2000 W @ 4 Ω |
1600 W @ 8 Ω |
Max output voltage / current |
Max unclipped output voltage@8 Ω |
|
|
115 Vpeak |
Current |
|
|
45 Apeak |
AC main power |
Power supply |
Universal, regulated switch mode with PFC (Power Factor Correction) |
Nominal power requirement |
|
|
100-240 V ±10%, 50-60 Hz |
Operating voltage |
|
|
90 V – 264 V |
Power consumption / current draw |
Idle |
|
115 V: 23 W – 0.34 A |
230 V: 23.3 W – 0.21 A |
1/8 of max output power @ 4 Ω |
|
115 V: 267 W – 2.5 A |
230 V: 274 W – 1.5 A |
THERMAL |
Operating temperature range |
|
|
0° – 45° C – 32° – 113° F |
Thermal dissipation* |
Idle |
|
115 V: 78 BTU/h |
230 V: 79 BTU/h |
1/8 of max output power @ 4 Ω |
|
115 V: 229 BTU/h |
230 V: 251 BTU/h |
|
Reviews
There are no reviews yet.