YAMAHA XM-4080 Power Amplifier 4x80W

Original price was: €993.00.Current price is: €957.73. incl. GR VAT

Available on backorder

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
Power Output Level 20Hz – 20kHz 1kHz THD+N=0.2%, 8Ω 80W x 4 Power Output Level 20Hz – 20kHz 1kHz THD+N=0.2%, 4Ω 115W x 4 Sensitivity, RL=8. Att.max +4dB S/N Ratio, 20Hz-20kHz (DIN AUDIO) 100dB Idle Power Consumption 40W 1/8 Power Consumption (4Ω) 500W Power Bandwidth, (Half power THD+N=0.5%) 10Hz – 40kHz Intermodulation Distortion, 60Hz: 7kHz, 4:1, half power 0.1% Frequency Response, f=20Hz-20kHz -0.5dB, 0dB, […]

 

Read more

Power Output Level 20Hz – 20kHz 1kHz THD+N=0.2%, 8Ω 80W x 4
Power Output Level 20Hz – 20kHz 1kHz THD+N=0.2%, 4Ω 115W x 4
Sensitivity, RL=8. Att.max +4dB
S/N Ratio, 20Hz-20kHz (DIN AUDIO) 100dB
Idle Power Consumption 40W
1/8 Power Consumption (4Ω) 500W
Power Bandwidth, (Half power THD+N=0.5%) 10Hz – 40kHz
Intermodulation Distortion, 60Hz: 7kHz, 4:1, half power 0.1%
Frequency Response, f=20Hz-20kHz -0.5dB, 0dB, 0dB
Residual Noise, 20Hz-20kHz(DIN AUDIO) -70dB
Voltage Gain, 8Ω, f=1kHz 100
Sensitivity, ATT. max 26dB
Maximum Input Voltage 22dB
Input Impedance 30kΩ (balance) 15kΩ (unbalance)
Controls, Front panel POWER switch (push on/push off), attenuator (31position) x 4
Controls, Rear panel MODE switch (STEREO/BRIDGE/PARALLEL) x 2 HPF switch (OFF/20Hz/55Hz 12dB/oct) x 2
Connectors, Output 5–way binding post/ch
Connectors, DATA PORT D-sub15P, Monitor:Output Level/ch,Active/ch, Model Detect Control:Mute/ch
Connectors, Power AC inlet x 1
Indicators, POWER x 1 (Green)
Indicators, SIGNAL x 4(Green)
Indicators, CLIP/LIMIT x 4 (Red)
Indicators, PROTECT/MUTE x 4 (Red)
Load Protection POWER switch on/off mute, DC-fault output relay off
Power Requirements UC: 120V / 60Hz,
Weight 10kg (22 lbs.)
Dimensions (W x H x D) 480 x 88 x 412.2 mm (18-7/8″ x 3-7/16″ x 16-1/4“) 

Weight 10.00 kg

Reviews

There are no reviews yet.

Be the first to review “YAMAHA XM-4080 Power Amplifier 4x80W”

Your email address will not be published. Required fields are marked *

Quick Comparison

YAMAHA XM-4080 Power Amplifier 4x80W removeRAM AUDIO S-3004 Power Amplifier 4x700 Watts removeRAM AUDIO T-1204 Power Amplifier 4x320 Watts removeLAB GRUPPEN FP 10000Q BP POWER AMLIFIER 4Χ2100 Watt/4Ohm removeAUDAC AUDPA74 Multichannel Digital Power Amplifier removeBEHRINGER EPQ304 EUROPOWER STEREO AMPLIFIER 4x75 Watts 4 Ohms, 4x50 Watts 8 Ohms remove
NameYAMAHA XM-4080 Power Amplifier 4x80W removeRAM AUDIO S-3004 Power Amplifier 4x700 Watts removeRAM AUDIO T-1204 Power Amplifier 4x320 Watts removeLAB GRUPPEN FP 10000Q BP POWER AMLIFIER 4Χ2100 Watt/4Ohm removeAUDAC AUDPA74 Multichannel Digital Power Amplifier removeBEHRINGER EPQ304 EUROPOWER STEREO AMPLIFIER 4x75 Watts 4 Ohms, 4x50 Watts 8 Ohms remove
Image
SKUH060.00045S-3004T-1204E008135AUDPA74EPQ304
Rating
Price Original price was: €993.00.Current price is: €957.73. incl. GR VAT Original price was: €2,008.79.Current price is: €1,599.59. incl. GR VAT Original price was: €1,339.20.Current price is: €1,071.35. incl. GR VAT Original price was: €5,450.00.Current price is: €5,200.00. incl. GR VAT Original price was: €489.80.Current price is: €465.00. incl. GR VAT Original price was: €300.00.Current price is: €279.89. incl. GR VAT
Stock

Available on backorder

Available on backorder

Available on backorder

Available on backorder

Available on backorder

Only 1 left in stock (can be backordered)

AvailabilityAvailable on backorderAvailable on backorderAvailable on backorderAvailable on backorderAvailable on backorderOnly 1 left in stock (can be backordered)
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content

Power Output Level 20Hz - 20kHz 1kHz THD+N=0.2%, 8Ω 80W x 4
Power Output Level 20Hz - 20kHz 1kHz THD+N=0.2%, 4Ω 115W x 4
Sensitivity, RL=8. Att.max +4dB
S/N Ratio, 20Hz-20kHz (DIN AUDIO) 100dB
Idle Power Consumption 40W
1/8 Power Consumption (4Ω) 500W
Power Bandwidth, (Half power THD+N=0.5%) 10Hz – 40kHz
Intermodulation Distortion, 60Hz: 7kHz, 4:1, half power 0.1%
Frequency Response, f=20Hz-20kHz -0.5dB, 0dB, 0dB
Residual Noise, 20Hz-20kHz(DIN AUDIO) -70dB
Voltage Gain, 8Ω, f=1kHz 100
Sensitivity, ATT. max 26dB
Maximum Input Voltage 22dB
Input Impedance 30kΩ (balance) 15kΩ (unbalance)
Controls, Front panel POWER switch (push on/push off), attenuator (31position) x 4
Controls, Rear panel MODE switch (STEREO/BRIDGE/PARALLEL) x 2 HPF switch (OFF/20Hz/55Hz 12dB/oct) x 2
Connectors, Output 5–way binding post/ch
Connectors, DATA PORT D-sub15P, Monitor:Output Level/ch,Active/ch, Model Detect Control:Mute/ch
Connectors, Power AC inlet x 1
Indicators, POWER x 1 (Green)
Indicators, SIGNAL x 4(Green)
Indicators, CLIP/LIMIT x 4 (Red)
Indicators, PROTECT/MUTE x 4 (Red)
Load Protection POWER switch on/off mute, DC-fault output relay off
Power Requirements UC: 120V / 60Hz,
Weight 10kg (22 lbs.)
Dimensions (W x H x D) 480 x 88 x 412.2 mm (18-7/8" x 3-7/16" x 16-1/4“) 

  The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment. In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep. • Ultra-compact and lightweight 2-U high • Laser cut aluminum front panels with integrated carrying handles • Neutrik® XLR input connectors, input and signal link in 2 channel models • Input Link switch: allow daisy-chaining of the input signal • Neutrik® Speakon® output connectors • Detented sealed potentiometers for easy recall of volume settings • ICL™, PMS™, Hi-temp, Signal indicators per channel • Power on and Stand-by leds • Highly versatile with multiple configuration and additional module options • Full PC control via EtheRAM (with EtheRAM Control module) • Switchable ICL™ clip-limiters per channel • Switchable (30-50 Hz) sub-sonic highpass filter per channel • Three-position gain selector (26, 32 or 38 dB) • Dual or bridge mode selector • Twin temperature controlled, back to front cooling fans • Oversized power components (high SOA reserve specification) Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility. Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics: • 2-way stereo crossover (dual mono or single bridged sub output) • 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz) • Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB) • Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB) DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics: • 4 Inputs/4 Outputs or 2 In/2 Out free route configurable. • 24 bits/192 kHz 256x Oversampling Converters. • Output Delay: 0 to 7.1 meters (20.69ms) per channel. • XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel. • EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB). • Gain, Mute and Phase inversion per channel. • RMS Power and Peak Voltage output limiter per channel. • Real Time operation from USB or front panel configuration. Standard Signal Inputs Module EtheRAM Control Module Ethernet Audio Transport (Coming soon) Analog Processor Module DSP44_S Module EtheRAM Control Module AES/EBU Digital Input (Coming soon)
OUTPUT POWER S-1500 S-2000 S-3000 S-4000 S-6000 S-3004 S-4004 S-4044 S-6004 S-6044
1kHz, 1.0% THD
2 ohms 2x880W 2x1190W 2x1570W 2x1950W 2x2950W 4x700W 4x980W - 4x1440W -
4 ohms 2x575W 2x790W 2x1100W 2x1380W 2x2025W 4x500W 4x670W 4x975W 4x1000W 4x1480W
8 ohms 2x325W 2x460W 2x630W 2x810W 2x1250W 4x300W 4x430W 4x690W 4x620W 4x1015W
Bridge @ 4ohms 1760W 2380W 3140W 3900W 5900W 2x1400W 2x1960W - 2x2880W -
Bridge @ 8ohms 1150W 1580W 2200W 2760W 4050W 2x1000W 2x1340W 2x1950W 2x2000W 2x2960W
P. N. 12dB C.F.
2 ohms 2x975W 2x1360W 2x2060W 2x2460W 2x4225W 4x890W 4x1170W - 4x2080W -
4 ohms 2x610W 2x880W 2x1240W 2x1600W 2x2600W 4x580W 4x820W 4x1230W 4x1280W 4x2110W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz Phase Response (@1W 20Hz-20kHz): ±15deg Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB Voltage Gain (selectable): 26/32/38 dB Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V 3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB 3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A 3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™
 
• Eight and four channel models with 300W and 150W per channel • Minimal footprint and mass arround 200mm depth and 6 Kg • Optional Add-on card to interface with third party alarm systems with GPIO connections • FCM™ Faulty Channel Management system to avoid entire device shutdown • State-of-the-art layout for maximum performance and reliability • Highly oversized thermal dissipation design for maximum reliability • Superb distortion and noise figures • All channels bridgeable by pairs • Selectable gain in four channel groups (26, 32 and 38dB) • Subsonic filter per channel (35Hz user selectable) • Temperature and signal dependant, intelligent cooling system for minimal noise • Optimal heat extraction due to the air tunneled enclosure and insulator-less power device attachment to the heatsink • Direct connector-less output for maximum quality loudspeaker control • High grade engineering inside with the latest SMD technology • Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection • Critical electronic and mechanical parts selection • Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection • Detented and optionally tamper-proof volume potentiometers • Hi efficiency, two steps Class H Audio topology • Protection, Signal and Clip indicators per channel • Power On and Standby general indicators • Extremely compact, fully featured QuantaPulse Power supply • Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations • Factory preset worldwide mains voltage power supply • Laser cut four milimeters aluminium front panel • Rugged 2U steel chasis    
OUTPUT POWER T-604 T-1204 T-1208 T-2408
RMS, 1kHz, 1.0% THD+N
4 ohms 4x 160 W 4x 320 W 8x 150 W 8x 300 W
8 ohms 4x 115 W 4x 220 W 8x 100 W 8x 195 W
Bridge @ 8ohms 2x 320 W 2x 640 W 4x 300 W 4x 600 W
Pink Noise 12dB CF
4 ohms 4x 210 W 4x 415 W 8x 180 W 8x 370 W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz Phase Response (@1W 20Hz-20kHz): ±15deg Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >70dB Voltage Gain (selectable): 26/32/38 dB Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™
 
POWER AMPLIFIER 4 X 2100 WATT / 4Ω Very high power  and  channel density  –   •   The  four-channel  FP 10000Q delivers a  total of 10000 W  (4 x 2500 W @ 2 ohms)  in only 2U Four-channel fexibility –   •  Four channels in one cabinet increases effciency, fexibility and value  in powering monitor systems,  line arrays, and bi- or tri-amped systems. Adjacent channels bridgeable for 2- or 3-channel operation Lab.gruppen  sound  quality  –   •   FP  10000Q  amplifers maintain the impeccable sonic performance standards set by the original fP Series, with the same durability and even greater effciency NomadLink   • ®  network  ready  – Monitoring  and  control  of  key functions accessible via the  intuitive DeviceControl software and the robust, daisy-chained NomadLink® network Patented  Class  TD  amplifer  topology  –    • Road-proven  output stage delivers Class B audio quality with Class D effciency Regulated  Switch Mode  Power  Supply  (R.SMPS)  –    • Output power remains constant even with signifcant drops in the mains voltage Effcient cooling system –   •  Unique, lightweight Intercooler® cop- per cooling system dissipates more heat to allow extended peak output Adjustable parameters –   •  Selectable Gain, scalable Voltage Peak Limiter (VPL), and bridge-mode operation allow custom confgura- tion for any system or application XLR input connectors   • Heavy-duty binding post or Speakon output connectors   • Comprehensive  protection  and warning  –   •   Excessive  output current, DC, high  temperature, very high  frequency  (VHF), short circuit, open load, mains fuse protection, and soft start

The DPA series amplifiers are digital power amplifiers designed to meet the specialized needs of sound contractors for Multi-Zone distributed speaker systems. They are designed in six different models of Class D power amplifiers, divided in three different architectures to meet the requirements for all kinds of applications.

They combine the best of all features in one single series of amplifiers, providing an outstanding sound quality with all the known advantages of Class D Amplifiers. Such as the excellent efficiency and very low heat dissipation. And due to the complete passively cooled entity only a minimal of maintenance is needed, while ensuring maximum reliability.

The small size of a single rack space make them very interesting for fixed rack mount as well as mobile applications.

The DPA74 is built as multi channel power amplifier with four individual controllable channels containing various specific features and advanced protection circuitry which protects against DC malfunctioning, short circuit, overheating and overload.

The signal input connections are accommodated with balanced XLR connectors. The operation mode can be selected between Stereo mode, Bridge mode and Parallel mode. The output connections are accommodated with Euro-Terminal blocks.

  • Model Name / Type: DPA74 / Digital Amplifier
  • 8 ohms: 4 x 50 W
  • 4 ohms: 4 x 75 W
  • 8 ohms Bridge: 2 x 150 W
  • THD+N:
  • Signal / Noise: > 100 dB
  • Frequency Response: 20 Hz - 20kHz
  • Power Supply: 240 V AC / 50 - 60 Hz
  • Dimensions (W x H x D): 483 x 44 x 300 mm
Product Features:
  • 4 x 75 Watts into 4 Ohms; 4 x 50 Watts into 8 Ohms
  • ATR (Accelerated Transient Response) technology for ultimate punch and clarity
  • Ultra-light, ultra-low noise and ultra-efficient switch-mode power supply for noise-free audio, superior transient response and low power consumption
  • Independent limiters for each channel offer maximum output level with reliable overload protection
  • Detented gain controls for precise setting and matching of sensitivity
  • Precise Power, Signal and Clip LEDs to monitor performance
  • Servo-balanced XLR and 1/4" TRS inputs plus professional speaker connectors
  • Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
  • “Back-to-front" ventilation system including air filter for reliable operation
  • “Built-like-a-tank“, impact-resistant and all-steel 1U rackmount chassis
  • Minimum depth chassis (10.1" / 257 mm) and ultra-light weight design (8.8 lbs / 4.0 kg) fits into compact, inexpensive effects racks
  • High-quality components and exceptionally rugged construction ensure long life
Weight10.00 kg8.50 kg5.40 kg14.00 kg6.00 kg4.70 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 10.00 kg
Weight 8.50 kg
Weight 5.40 kg
Weight 14.00 kg
Impedance

Weight 6.00 kg
Weight 4.70 kg