YAMAHA XP-1000 2X155W POWER AMPLIFIER

Yamaha Power Amplifier - XP1000 2 x 110-Watts, 8-Ohms Stereo, 100-Volt, High Sound Quality,
20Hz-20kHz, High Reliability and High Stability, Light Weight and Compact Design of 2U Size,
High-Pass Filter.

The XP power amplifier series featuring high power, high quality, high reliability and high stability
matches various installation sound systems and provides superior acoustic features even in live
performance applications. The series is equipped with various protection circuits including a circuit
for detecting power-on/off, output protection circuit and DC detection circuit. Various indicators
display the status of the protection system. Indicators include PROTECTION indicator, TEMP
indicator that shows overheating of the heat sink, POWER/STANDBY indicator that shows the
power status, as well as SIGNAL and CLIP indicators for each channel.

APPLICATIONS:
Live Performance 
Churches 
Halls 
Banquet Rooms 
Conference Rooms 
Restaurants
 
5-model lineup ranging from 700W* output to 100W* output *(STEREO 8 ohms). 
High sound quality equivalent to upper-class models with parts and emphasizing
on superior sound. 
While realizing a design that ensures high sound quality, efficiency has been
planned down to the finest details for full achievement of both high-definition sound
and superior value. 
Yamaha's exclusive state-of-the-art high-efficiency amplifier driving technology
EEEngine installed. 
A gain switch that can be changed to +4dBu / 26dB / 32dB has been installed on the
rear panel for compatibility with a wide variety of input levels. 
Light weight and compact design of 2U size for installation in any location. 
Monitor and remote terminals for monitoring and control from a remote location. 
High-accuracy 1dB-step detented attenuator. 
Various terminals and features suitable for professional use. 
Special high-pass filter that enables change of cut-off frequency. 
Equipped with various protection circuits, indicators and stepless low-noise fans. 
Best matches with the digital mixing engine DME64N/24N and Installation series
speakers.
 
Output Power, 8? 100W+100W
S/N Ratio, 20Hz-20kHz 96dB
Idle Power Consumption 20 Watts
1/8 Power Consumption (4?/Pink noise) 170 Watts
Power Bandwidth (half power THD+N=0.5%) 10Hz-40kHz
THD+N 20Hz ? 20kHz, half power 0.1%
Intermodulation Distortion, 60Hz: 7kHz, 4:1, half power 0.1%
Frequency Response RL=8?, Po=1W,HPF=OFF 0dB
Channel Separation, Half power RL=8? 1kHz, ATT. Max input 600? shunt 70dB
Residual Noise Att. min, 20Hz-20kHz (DIN AUDIO) -70dBu
Damping Factor, 8?, f=1kHz 200
Voltage Gain, ATT. max 32dB or 26dB or +4dBu input sensitivity by select switch
Maximum Input Voltage +22dBu
Input Impedance 20k?(balance) 10k?(unbalance)
Controls, Front panel Power switch(push on/push off), attenuator(31position) x 2
Controls, Rear panel Mode switch(Stereo/Bridge/Parallel) x 1, HPF switch x 2,
Gain Select switch x 1
Connectors, Input XLR-3-31 type/ch, Euroblock connector(balance)/ch
Connectors, Output Speakon/ch, 5way binding post x 1
Connectors, Monitor/Remote Dsub15P x 1
Indicators Power/Standby x 1(Green/Orange), Signal x 2(Green), Clip/Limit x 2(Red)
Amplifier Protection Thermal: cut the output(heatsink temp ? 90°C) do not return
automatically
Power Requirements UC: 120V/60Hz, EU: 230V/50Hz, A: 240V/50Hz
Weight 12kg (26.5 Ibs.)
Dimensions (W x H x D) 480 x 88 x 456 mm (18-7/8" x 3-7/16" x 17-15/16“)
 

• 2Χ350W 8Ω 2x500W 4Ω 2x650W  STEREO MODE
  
  
  
• BRIDGE 2000W 4 Ω
• 16Kg

• 2 x 1,000 Watts into 2 Ohms; 2 x 750 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)
• Precise Power, Signal and Clip LEDs to monitor performance
• XLR and 1/4" TRS input connectors for compatibility with any source
• Professional speaker connectors and "touch-proof” binding posts support most speaker wiring systems
• Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies
• Independent limiters per channel offer reliable protection against overload and distortion
• High-current toroidal transformer for ultra-high transient response and absolute reliability
• Ultra-reliable Toshiba/Fairchild power transistors
• Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
• “Back-to-front” ventilation system including air filter for reliable operation
• “Built-like-a-tank,” impact-resistant, all-steel 2U rackmount chassis
• High-quality components and exceptionally rugged construction ensure long life
• Conceived and designed by BEHRINGER Germany

• Rack mount stereo powered monitor speaker system
• New AES/EBU digital input
• lndependent MUTE function
• Sophisticated control panel section
• Ideal where space is at a premium

• Stereo analog balanced +4DBu inputs with combo connectors (XLR & 1/4" plug).
• AES/EBU digital input with XLR connector working with fs 44.1kHz to 96kHz.
• Sophisticated control panel section including 26-dot stereo LED meter, biaxial stereo gain control, phone jack, Channel select switch as well as Input select switch.
• Independent MUTE function by holding down CH SEL key for a while.
• Auto Mute when powering on*.
• D-class power amplifier (10W x 2) for clear sound reproduction and light weight construction.
• Multi-voltage power supply.

Speaker Section

• Unit: 110 x 40mm cone type, magnetically shielded, x 2
• Impedance: 8 ohms
• Output SPL: 84 dB/W (1m)
• Frequency response: 200Hz to 20kHz

Amplifier Section

• Rated output power: 10W or more (8 ohms, 1kHz)
• Residual noise: -60 dBV or less (DIN AUDIO)
• Distortion: 0.5% or less (10W / 4 ohms, 1kHz)

Digital input

• Connector: XLR-3-31 type
• Digital input Format: IEC60958 (AES/EBU)
• Digital inputSampling frequency: 44.1kHz to 96 kHz
  

Analog input

• Connector: XLR / 1/4" combi-jack
• Analog input Nominal input level +4dBu (XLR), -10 DdBV (1/4“)
• Analog input Input impedance 10k ohms or more

Phones

• Connector: 1/4" stereo jack
• Applicable load imp. 8 ohms or more
• Rated output power 20mW + 20mW (32 ohms, 1kHz)

General

• External dimensions: 430(W) x 44(H) x 282(D) mm
• Weight: Approx. 3.5kg
• Power requirement: 100 - 240V~, 50/60Hz
• Power consumption: 10W

Power Output Level R-300 PLUS

STEREO
8ohm(T.H.D 0.05%)  170W+170W
4ohm(T.H.D 0.05%)  250W+250W

BRIDGED MONO
8ohm(T.H.D 0.05%)  460W
8ohm(T.H.D 0.5%)    500W

Frequency Response 20Hz- 20kHz, ±0.5dB

Convection Cooled

SoftStart Protection System

Balanced 10kΩ@0.775V Inputs

BASIC Series - Intelligent Power

BASIC - that's meeting the tightest budgets and professional requirements
in reliability, flexibility and sound. Alone or in combination with the other
products of the Bittner portfolio.
The consequent realisation of the Bittner quality standards indicates once
more our understanding of the contracting business. It underlines our philosophy
that cost consciousness has nothing to do with giving up standards. Compromise
is a word unknown to Bittner Audio!
The incorporation of detent potentiometers, clip limiter, protection circuits for
any imaginable situation, as well as a first-class production process using only
highest-quality components made the BASIC series the choice of most contractors.

Certainly more than basic!

High Tech SMT design
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
XLR Inputs
Speakon and Binding Posts
Clip Limiter
Toroidal transformers
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed, low noise fans
Detent potentiometers
Stereo / Bridged / Parallel Mode
Ground Lift
Robust Steel Chassis
3 Year Warranty

TECHNICAL DATA:
Basic 800:  2x 400 W @ 4 Ohm
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.03%
Signal-to-Noise Ratio: < -102 dB
Channel Seperation: > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  > 400 @ 4 Ohm
Cooling:  2x Fan (temp. reg. variable speed)
Weight:  13 kg.
Dimensions : 2 RU/483x89x265 mm (19" x 3.5" x 12.6“)

Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 900 W, 4 Ω - 600 W, 8 Ω - 380 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1700 W, 4 Ω - 950 W, 8 Ω - 480 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1800 W, 8 Ω - 1200 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +3.1 dBu (1.11 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 14.8 kg (32.6 lbs)