AUDIX TM1 Omni-directional test and measurement microphone

Omni-directional test and measurement microphone for RTA and software systems.

The TM1 is a 6 mm pre-polarized condenser microphone used for test and measurement applications. The TM1 is known for its linearity, accurate response, consistency, ease of use and affordability.

Equipped with a uniformly controlled omnidirectional polar pattern, the TM1 is designed to capture acoustic measurements for room analysis software programs, real time analyzers and other sound control devices. With a flat frequency range of 20 Hz – 25 kHz, the TM1 is an excellent tool for sound engineers, sound companies and recording enthusiasts.

The TM1 is designed, machined, assembled and tested by Audix in the USA.

Model Variation: TM1 PLUS - includes calibration data file and sensitivity, threaded acoustic windscreen, and CA4231 machined calibration adapter *

*Bruel & Kjaer® 4231 sound level calibrator or equivalent

Mικρόφωνο μετρήσεων με flat απόκριση ιδανικό για μέτρηση με μηχανήματα ανάλυσης, πυκνωτικό, Omni-directional, Frequency response: 20 Hz to 20 kHz, ευαισθησία -37dBv/pa (14mV/pa), μεταλική κατασκευή, περιλαμβάνει σκληρή θήκη.

Features:

• Flat response, excellent electro-acoustical characteristics
• Ideal for room analysis systems, measurement, testing and recording
• Standard 1/2" measurement diameter
• Type: Back-electret condenser mic
• Pickup Pattern: Omni-directional
• Frequency Response: 20~ 20000Hz
• Sensitivity: -37dBV/Pa (14mV/Pa)
• Rated Impedance: 200 ohm
• Max. SPL: 132dB
• Signal-to-noise Ratio: >70 dB
• Power Supply: 9~52V Phantom power
• Current Consumption: 2mA
• Connector: 3-pin XLR gold-plated
• Weight: 150g (5.3 oz)
• Weight Unpacked: 1.17 lb(0.53 kg)
• Weight Packed: 1.17 lb(0.53 kg)
• Width Packed: 4.75“(12.065 cm)
• Depth Packed: 12“(30.48 cm)
• Height Packed: 3“(7.62 cm)

Internally switchable proximity effect compensation and sensitivity reduction.

The BCM 104 condenser microphone is the first product in the new Broadcast Line,
which is especially tailored to the demands of professional radio announcing.
What sets the Broadcast Line apart is a completely independent, functionally-
optimized design derived from extensive 3D simulations.
The large-diaphragm condenser capsule used in the BCM 104 has a cardioid directional
pattern with internally switchable proximity effect compensation. A second switch allows
the sensitivity to be reduced by 14 dB.
The microphone headgrill twists off easily for quick cleaning. Neumann offers optional,
color-coded headgrills so that, for reasons of hygiene, each announcer working at an
announcing desk can use his or her individual headgrill.
Directly in front of the capsule, mounted on a frame holder, is a piece of fine gauze that
serves as a built-in popscreen.
The BCM 104 has an elastic mount against structure-borne noise, that is compatible with
standard broadcast-segment microphone arms.

Features:
Cardioid microphone for broadcast & studio
Large diaphragm condenser capsule with
switchable proximity compensation
Distinctive design
Integrated pop screen
Quick release head grille for easy cleaning
Individual head grilles available for each user

Acoustic features
The microphone headgrill houses the K 04 large-diaphragm capsule, which has a flat frequency
response up to 3 kHz. Higher frequencies have an increased presence of 2 dB maximum.
Since the above-mentioned microphone characteristics are obtained without the use of resonance
effects, the microphone features excellent transient response and transmits all transient phenomena
of music and speech without any coloration.
The integrated Pop Screen
A pop screen not only prevents the occurrence of plosive pop noises in vocal recordings, but also
efficiently prevents unwanted particles, from respiratory moisture, nicotine, to food remnants, from
settling on the diaphragm.
The pop screen can be removed for cleaning without the use of tools.

Electrical features
Instead of a transformer to couple the microphone output to the supply voltage, the BCM 104
has an electronic circuit which, like a transformer, provides for good common mode rejection.
Interference induced in the balanced modulation line is thus suppressed as usual.
With a very low self-noise of 7 dB(A), and an overload capability extending to 138 dB SPL,
the BCM 104 has a dynamic range of 131 dB (DIN/IEC 651).
Filter and Preattenuation
The BCM 104 amplifier has a linear operation down to 20 Hz. An active filter efficiently suppresses
signals below this frequency. In order to compensate for the proximity effect, a high-pass filter,
electronically activated by a switch, is built into the microphone. This filter reduces frequencies
below 100 Hz by 12 dB/octave.
A 14-dB preattenuation switch is provided in order to adjust the sensitivity, if necessary,
to transmission circuits designed for dynamic microphones. But this will increase the
self noise by 14 dB.Both switches are located inside the microphone housing, since they
will normally be operated only once, when the broadcasting facility is set up.
Mounting
The preferred mode of operation is to suspend the BCM 104 from a standard studio boom arm.
A thread adapter to fit different connector threads is included.
In order to provide protection from structure-borne noise, both the capsule and the microphone
in its mount are elastically suspended.
The optional SG 5 swivel mount allows additional angling of the BCM 104 by +/-90 degrees.

Application hint:
While designed to be an announcer's mic for broadcasting and studio, this is
just one of the most common applications. With additional experimentation,
you will gain maximum use from this microphone.

Technical Description:
Acoustical operating principle: Pressure gradient transducer
Directional pattern: Cardioid
Frequency range: 20 Hz -- 20 kHz
Sensitivity at 1 kHz into 1 kohm: 22 mV/Pa
-14 dB attenuation: 4.4 mV/Pa
Rated impedance: 50 ohms
Rated load impedance: 1000 ohms
Equivalent SPL CCIR 468-3: 18 dB
Equivalent SPL DIN/IEC 651: 7 dB-A
S/N ratio CCIR 468-3: 76 dB
S/N ratio DIN/IEC 651: 87 dB
Maximum SPL for THD 0.5%: 138 dB
Maximum SPL for THD 0.5% with preattenuation: 152 dB
Maximum output voltage: 10 dBu
Dyn. range of the mic. amplifier DIN/IEC 651: 131 dB
Supply voltage: 48 V +/- 4 V
Current consumption: 3.2 mA
Matching connector: XLR 3 F
Weight: 500 g
Diameter: 64 mm
Length: 85 mm

• Electret measuring microphone for measuring systems and audio recordings
• Designed for measuring PA systems, speakers and room acoustics
• Perfect complement to any real-time analyzer
• Flat frequency response for high precision
• Sturdy all-metal construction and narrow design
• Polar pattern: Omnidirectional

Μια ολοκληρωμένη πρόταση της RODE για ηχογράφηση φωνής και μουσικών οργάνων με το νέο πυκνωτικό μικρόφωνο,ΝΤ2-Α.Με κάψα διαμέτρου 1'',τρείς επιλογές πολικών διαγραμμάτων αλλά και τα απαραίτητα αξεσουάρ που περιλαμβάνονται στο πακέτο-αντικραδασμική βάση,καλώδιο ΧLR,Pop Filter,θήκη,εκπαιδευτικό DVD-γίνεται η ιδανικότερη επιλογή για επαγγελματικά αποτελέσματα.

• Ακουστική αρχή : Externally polarized 25 mm (1”) dual diaphragm.
• Directional pattern : Multi-pattern
• Απόκριση συχνότητας : 20 Hz ~ 20 000 Hz
• Αντίσταση Εξόδου : 200 Ω
• Λόγος σήματος προς θόρυβο din iec 651: 87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
• Σχετικό επίπεδο θορύβου : 7 dBA SPL (per IEC651, IEC268-15)
• Μέγιστη Στάθμη Εξόδου spl: 147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
• Ευαισθησία : -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
• Δυναμική περιοχή din iec 651: 140 dB (per IEC651, IEC268-15)
• Τροφοδοσία : 48 Volts (P48)
• Βάρος χωρίς μπαταρία : 860 grm (4.23 oz)