| Content |
- Very compact headphone amplifier for in-ear monitoring
- XLR and jack input (combined, lockable)
- 3.5 mm Mini-jack jack for earphones
- Built-in stereo / mono source switch
- Volume control with on / off switch
- Operation up to 12 hours with 2 AAA batteries or rechargeable batteries (not included, suitable batteries: Article Nr. 417474)
- Dimensions (H x W x D): 33 x 38 x 132 mm
- Weight: 0.140 kg
- Includes belt clip
|
Προενισχυτής In ear monitor με mono ή stereo λειτουργία με διακόπτη και δυνατότητα mix (2 XLR In). Ρύθμιση έντασης. Έξοδος mini jack stereo. Λειτουργεί με μπαταρία 9V & τροφοδοτικό PSU-SB (Δεν περιλαμβάνεται).
| Κατασκευαστής |
BEHRINGER |
| Κανάλια Μίξης |
2 |
| Μοντέλο |
P1 |
| Part Number |
000-AZM |
| Εγγύηση |
1 Χρόνος Εγγύηση |
|
Τεχνικά Χαρακτηριστικά: INPUT: 1 audio stereo, on 6.5mm stereo phone socket.
OUTPUTS: 5 audio stereo, on 6.5mm stereo phone sockets.
CONTROL: 5 stereo output level controls (front), 1 Mono switch (rear).
GAIN RANGE: 70 dB (- 60dB to +10dB).
16.5cm x 12cm x 4.5cm
0.68 kg. | Palmer Monicon, and the volume is right!
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal.
The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking "little helper" that is a typical Palmer product.
- Type: passive
- Number of channels: 2
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: +20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: +20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz +/- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator + mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
| The LD Systems HPA 1 is a versatile headphone amplifier with high power output for stage, studio and home recording and is the perfect solution for wired in-ear-monitoring.. The compact device in a rugged, ergonomically shaped plastic housing with soft-touch surface and practical belt clip is very extensively equipped.
In addition to locking XLR connectors for the stereo signal L/R input, the HPA 1 has a balanced 3.5 mm stereo jack as AUX input, which can be used in parallel for clicks or playback. It is protected for safe operation against excessive input levels; a hollow pin socket with negative internal contact enables the connection of a network adapter for fixed operation.
A 3.5 mm stereo jack is provided as earphone and headphone output. Volume level and balance can be set with easy-grip knobs, a push-button switches between the summed mono and stereo signals. A full-fledged limiter is integrated for distortion-free playback and as protection against feedback.
The LD Systems HPA 1 has bi-colour LEDs to facilitate the features overview, which displays the response of the limiter during peaks and the battery status. At 165 grams, the headphone amplifier is distinctly light-weight and can be operated for up to 12 hours thanks to a high quality 9 V block battery.
- Model Name: LDHPA1
- Product Type: headphone amplifier
- Type: 1-channel stereo
- Inputs: Main Input (Stereo), 1 x Aux In (Stereo)
- Input Connections: XLR-F (L + R Input, balanced), 3.5 mm stereo jack (Aux In)
- Input Impedance: 6 kOhm (XLR In), 10 kOhm (3.5 mm jack)
- Input Sensitivity: 3 dBu (XLR In), -6 dBV (3.5 mm jack)
- Max. Input Level: 16 dBu (XLR In), 7 dBV (3.5 mm jack)
- Protection Circuits: Audio Limiter, Max. Input leveling, Power OFF -Mute relay
- Headphone Outputs: 1
- Headphone Output Connectors: 3.5 mm stereo jack
- Power Output: 2 x 1.65 Vrms / 1% THD 33 Ohm Load
- Minimal Connected Impedance per Channel: 16 ohms
- Frequency Response: 20 Hz - 40,000 Hz
- THD 1 kHz Sine: 0.04%
- Controls: Power/Volume, Balance L/R, Stereo/Mono (Focus) switch,
- Indicators: Signal (Green) / Peak (Amber), Battery (low battery: red) / Power LED (Power ON: green)
- Power Supply: 9 V DC block battery, DC jack
- Operating Voltage: 9 V DC
- Power Consumption: Nom. 70 mA / Max. 150 mA
- Housing Material: plastic
- Housing Surface: soft-touch
- Housing Colour: black
- Width: 80 mm
- Height: 42.5 mm
- Depth: 133 mm
- Accessories (included): belt clip, 1 m 3.5 mm stereo jack cable
|
Monitor Mixer Ακουστικών
Πρόβλημα: Ο μουσικός χρειάζεται να ακούει το όργανο του με ακουστικά, μεμονωμένα ή μιξαρισμένο από την έξοδο της κονσόλας, την έξοδο ενός CD player, ή οποιαδήποτε άλλη στέρεο πηγή. Στην κεντρική κονσόλα όμως, πηγαίνει μόνο το σήμα μικροφώνου.
Λύση: Συνδέστε το MyMONITOR ανάμεσα στο μικρόφωνο ,την line πηγή και την κονσόλα .Οι στάθμες εντάσεως καθώς και μίξης του μικροφώνου και line πηγής μπορούν να ρυθμιστούν μέσω ακουστικών. Το MyMONITOR μπορεί να τροφοδοτηθεί μέσω μπαταρίας ή τροφοδοτικού AC και μπορεί να χρησιμοποιηθεί οπουδήποτε, όπως από ένα μεγάλο φεστιβάλ ή σε εφαρμογές όπου δεν υπάρχει η δυνατότητα τροφοδότησης ηλεκτρικού ρεύματος. Δεν υπάρχει περιορισμός στην σύνδεση τύπων μικροφώνων. Εκτός από δυναμικά μπορούν να συνδεθούν και πυκνωτικά μικρόφωνα, καθώς η απαιτούμενη τροφοδοσία 48V μπορεί δοθεί από την κονσόλα μας ή οποιαδήποτε άλλη συσκευή οπού έχει αυτήν την δυνατότητα .
MyMONITOR - Personal Headphone Monitor Mixer Overview
Problem: A performer needs to hear him/herself through headphones exclusively or mixed
with the output of a mixer, CD player, tape deck, or other stereo line level source. Only the
mic signal, however, should be going to the main mixer.
Solution: Connect MyMONITOR between the mic and line source, and the mixer. The Mic
and line Monitor levels can then be adjusted for mix and volume through the headphones.
Only the mic signal will go to the board. And since MyMONITOR can be AC or battery powered,
the unit can be used on a large stage or wherever there is no AC outlet nearby. Dynamic or
condenser mics can be used since phantom power would come through the Mic Thru jack from
the mixer or other source.
MyMONITOR - Personal Headphone Monitor Mixer Specifications:
Signal To Noise Ratio 90dB
Gain 15dB (1/4 in), 50dB (XLR)
Maximum Input Level -20dB mic, 40dB Monitor
Output Impedance 10 ohms
Power Requirements 12V DC (Adapter included) or one 9V battery
Phantom Power ON/OFF switch
Power LED indicator
Dimensions 4.5x2.75x1.5 inches (112mm x 72mm x 40mm)
Weight 1.3lb (590g)
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.