Content | Απολαύστε τη μοναδική ζεστασιά του βινυλίου και την αναλογική λεπτομέρεια με την ποιότητα του phono pre-amp.
Υπάρχει κάτι μοναδικό όταν ακούτε βινύλιο, κάτι που τα ψηφιακά μέσα δεν μπορούν να το αναπαράγουν με τον ίδιο τρόπο. Ενώ οι τελευταίες ψηφιακές μορφές ακούγεται εξαιρετικά, υπάρχει λεπτομέρεια και ζεστασιά που δεν μπορούν πάντα να εκφράζονται σε 0s και 1s. ωδές.Ένα τρίξιμο μπορεί να προσθέτει χαρακτήρα στη ζωντανή μουσική .Ο CP2 σας επιτρέπει να απολαύσετε όλα αυτά με οποιοδήποτε σύστημα hi-fi σε εξαιρετική ποιότητα.
Oι περισσότεροι ενισχυτές hi-fi δεν θα σας επιτρέπουν να συνδέσετε ένα πικάπ άμεσα. Θα πρέπει να συνδεθείτε μέσω του στάδιου phono ( προενισχυτή phono) που κάνει το πολύ μικρό σήμα από το πικάπ ,αρκετά ισχυρό για την κύρια ενισχυσή του.
Αλλά είναι πολύ εύκολο να προσθέσετε θόρυβο σε αυτό το στάδιο. Αυτός είναι ο λόγος που έχουμε σχεδιάσει το CP2 ,χρησιμοποιώντας "συστατικά" που έχουν επιλεγεί για εξαιρετική ακρίβεια της ενίσχυσης του σήματος, χωρίς να το αλλοιώσει.
Αλλά και αν ο ενισχυτής hi-fi σας , σας επιτρέπει να συνδέσετε ένα πικάπ άμεσα,κατά πάσα πιθανότητα η ποιότητα προενίσχυσης του είναι "φτωχή" με το υποτυπώδη στάδιο ενίσχυσης που έχει ενσωματωμένο, που κατασκευάστηκε μαζικά .
Το CP2 πιστεύουμε ότι απευθύνεται σε κάθε σοβαρό εραστή βινύλιου ,που θα ακούσετε αμέσως τα οφέλη του. Συνδεστε το χρησιμοποιώντας ένα μόνο καλώδιο διασύνδεσης ήχου, για να εκτιμήσετε την εκπληκτική διαύγεια, τη μουσικότητα και την ανάλυση από τη συλλογή βινυλίου σας.
Το κύκλωμα έχει τελειοποιηθεί με πολλαπλά τρανζίστορ ,που παράλληλα εξασφαλίζει τη χαμηλότερη δυνατή παραμόρφωση και θόρυβο.ωδές. Μια ασπίδα χαλκού παρέχει περαιτέρω προστασία σε αυτό το εξαιρετικά ευαίσθητο τμήμα του κυκλώματος, για τη μείωση του θορύβου που μπορεί να εγχυθεί μέσα στο σήμα. Αυτό που είναι ιδιαίτερα σημαντικό στη Moving Coil κεφαλή, επειδή το σήμα του είναι ακόμα πιο χαμηλό και πιο ευαίσθητο από της Moving Magnet, γι'αυτό χρειάζεται ακόμη περισσότερη ενίσχυση.
Ένα εξαιρετικά ακριβή, υποηχητικό φίλτρο αφαιρεί επίσης το κοινό πρόβλημα των ανεπιθύμητων χαμηλών συχνοτήτων που είναι "αθόρυβες" , αλλά μπορεί να βλάψουν το γούφερ των ηχείων και ακόμα περισότερο το υπογούφερ
Χαρακτηριστικά
- Moving Magnet-Moving Coil
- Gain @ 1kHz39dB55dBB
- Nominal output300mV300mV
- Sensitivity for nominal output3.35mV3.35mV
- THD 20Hz-20kHz83dB>69dB
- LessLessLess
- Dimensions (H x W x D)46 x 215 x 133
- Weight 0.9kg
|
Μετά την μεγάλη επιτυχία με το προενισχυτή Pre-73, η ζήτηση για έκδοση σε φορμά API 500 ήταν τεράστια. Είμαστε λοιπόν στην ευχάριστη θέση να παρουσιάσουμε το Pre-573 ! Το Pre-573 είναι μία κάθετη μονάδα που έχει τον ήχο και τα χαρακτηριστικά που έκαναν το Pre-73 τόσο μεγάλη επιτυχία αλλά και με κάποιες επιμέρους βελτιώσεις.
Το κύκλωμα χρησιμοποιεί ακόμα το τμήμα προενισχυτή και εξόδου από τον κλασικό 1073, προσαρμοσμένα ώστε να λειτουργούν στη μορφή rack API. Έχει συνολικό gain -15 έως 80 dB. H ρύθμιση στα 10 - 70 dB γίνεται από ένα περιστρεφόμενο διακόπτη και υπάρχει ένας ξεχωριστός διακόπτης για να επιλέξετε ένα επιπλέον 5 ή 10 dB. Η είσοδος μπορεί να διαμορφωθεί να δέχεται σήματα Line από άλλο διακόπτη.
Η αντίσταση εισόδου της εισόδου μικροφώνου μπορεί να αλλάξει μεταξύ 1200 και 300 ohm. Phantom power και φάση μπορούν να επιλεγούν από διακόπτες στο μπροστά πάνελ. Ένα πρόσθετο χαρακτηριστικό, χρησιμοποιώντας το ίδιο κύκλωμα όπως το Pre-73 DLX, είναι το ενεργό DI-εισόδος με μια υψηλή αντίσταση περίπου 2 Mohm. Το σήμα εξόδου από το ενεργό κύκλωμα DI περνά διαμέσου του μετασχηματιστή εισόδου για να προσθέσει επιπλέον χαρακτήρα.
Το DI είναι πολύ ευέλικτο, δεδομένου ότι μπορεί να αλλάξει σε μια καθαρά παθητική είσοδο με ένα διακόπτη. Η είσοδος DI είναι τότε ακριβώς ίδια όπως και στον Pre-73 Mk2, παρακάμπτοντας το μετασχηματιστή , δίνοντας σύνθετη αντίσταση εισόδου περίπου 100 kohm.
Αυτές οι δύο επιλογές DI καθιστούν δυνατή τη διαφοροποίηση του ηχητικού χαρακτήρα σε ηλεκτρικά όργανα , μπάσσα, synth κλπ
Ένα νέο χαρακτηριστικό είναι η διακοπτόμενη λειτουργία AIR που προσθέτει μια μικρή αύξηση πάνω από 10 kHz που κορυφώνεται σε 2 dB στα περίπου 35 kHz.
Μια απλή αλλά αποτελεσματική ένδειξη υπερφόρτωσης προσφέρεται από ένα και μόνο LED λαμπάκι που ξεκινά κόκκινο στα +4 dBu και στη συνέχεια αυξάνει την ένταση του μέχρι τη μέγιστη στάθμη εξόδου.
H Pre-573 έχει μια ειδική υποδοχή στο πίσω μέρος που επιτρέπει τη διασύνδεση με άλλα GAP 500 |
Το PRE73 είναι ένα πιστό emulation του κλασικού Neve 1073 και σε απίστευτα χαμηλή τιμή. Είναι ο πρώτος μονοκάναλος προενισχυτής με full discrete ροή σήματος και με τρείς ξεχωριστούς μετασχηματιστές για την balanced είσοδο μικροφώνου, την line είσοδο και έξοδο.
Με χαρακτηριστικό ήχο που παραπέμπει απευθείας σε μερικούς απο τους καλύτερους προενισχυτές μικροφώνου ανεξαρτήτως τιμής, δεν είναι τυχαίος ο θόρυβος που έχει αναπτυχθεί διεθνώς για το μικρό αυτό θαύμα !
The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
- LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme.
|
The U5 high-voltage DI-preamp combines a unique passive tone selector with a variable
gain preamp and filter. The high input impedance accepts a wide variety of signal levels
and instruments from acoustic guitars to high-output active bass guitars and keyboards.
The U5 direct box is loaded with sonic character and user features professionals demand.
U5 FEATURES
Pure Class A, 100% discrete design
Smooth musical detail and sonic excellence
Variable gain preamp to +30dB.
Dual microphone and line outputs
Hi-Z 3,000,000 ohm input impedance
Very low noise -100dB
High headroom +30dB
Six tone bank selections.
DC coupled Class A output for superior bass
High cut switch eliminates noise
LED active signal indicator
Headphone monitor output jack
Low distortion less than 0.5% THD and IMD
High level 400 watt speaker input
Active to thru selector - ground isolation switch
100% discrete power supplies for audio path
Internal toroidal power supply for low noise
Long lasting, stainless steel hardware
SONIC EXCELLENCE
The Avalon U5 Pure Class A instrument DI & preamplifier is the most powerful direct box
available today. Designed to optimize absolute signal integrity and musical performance,
the U5 includes many features and sonic excellence unequaled by lesser designs. The
U5 is ideal for bass guitar and acoustic instruments, electric guitars, keyboards, synthesizers
and low output pickups.
Features include state-of-the-art, high input impedance input stage for zero load effect on
sensitive pickups and keyboards, 100% discrete, Pure Class A signal amplifiers, practical
user features and rugged hardware designed to deliver true high performance audio for many
years.
DESIGNED FOR DEEP & CONTROLLED BASS
Avalon U5 DI-preamps have been in use around the world since 1995. They have found their way
into the world's leading musicians rigs and recording sessions and been featured on thousands
of the best selling (and sounding) albums and live performances.
MINIMUM SIGNAL PATH DESIGN
The U5 includes a variable gain Class A preamplifier to boost low level pickup signals and a high
level speaker input for capturing the live sound of the instruments amplifier. Six passive tone-EQ
curves are also included to enhance a variety of acoustic and electric instruments. A high-cut switch
eliminates unwanted acoustic pickup and high frequency noise, while a headphone monitor amp
has been included for personal listening. Twin DC coupled Class A output amplifiers drive both low
level microphone preamp inputs and high level +4dB inputs for direct to tape recording or processing.
The active-to-thru switch selects either the instrument input directly or sends the boosted-equalized
signal to the amplifier via the front panel jack. A ground isolation switch eliminates any possible earth
loop or AC buzz problems with complete safety.
U5 SPECIFICATIONS
Circuit Topology: 100% discrete, high-voltage Class A
Gain: Switched 3dB steps, maximum gain +30dB
Input Impedance: 3 ,000,000 ohm unbalanced (single ended)
Maximum Input Level +24dBu unbalanced, 400w speaker input
Output Connectors (2): XLR type, pin 2 hot electronic balanced
Maximum Output Level (Class A): +30dBu DC coupled, balanced 600 ohms (mic and line out)
Headphone Output: 0.5w into 600 ohms
Noise 20kHz Unweighted: -100dBu minimum gain position
Distortion THD, IMD: 0.1% at +10dB
Frequency Response, -/+0.5dB: 5Hz to 100kHz
Frequency Response, -3dB: 1Hz to 500kHz (input band limited)
High Cut Filter: -3dB at 8kHz minimum phase design
Tone Selector: Six position rotary switch, all passive filters
AC Power: Internal toroidal AC supply
Dimensions: 8.5 x 3.5 x 12 in (216 x 88 x 305mm)
Weight-Packed: 12lbs (5.4kg)
Rack mount kit (1) RM-1: Single U5 19 inch rack mount kit (holds one half rack unit)
Rack mount kit (2) RM-2: Dual U5 19 inch rack mount kit (holds two half rack units)
|
Το ΕΡΓΑΛΕΙΟ του κάθε σολίστα για προσωπική χροιά ήχου: EWI PDI-100 PARA ACOUSTIC DI Box
ΙΔΑΝΙΚΗ ΛΥΣΗ ΓΙΑ ΟΡΓΑΝΑ ΟΠΩΣ ΚΛΑΡΙΝΟ - ΑΚΚΟΡΝΤΕΟΝ - ΛΥΡΑ - ΚΙΘΑΡΑ
EWI PDI-100 PARA ACOUSTIC DI Box
This is a medium grade professional application Para Acoustic Active DI, which will work well on instruments with passive pickups or active pickups.
The construction is reasonably rugged and the components are well suited for the application yielding results that are typically acceptable for all but the most discerning artists.
The on-board tone and volume controls give the operator a lot of choices in shaping their sound prior to sending the signal to the mix console. This allows an artist to use this device in-place of or in addition to a traditional stage amp for their instrument. This is an excellent choice for IEM bands, or bands that like to keep their stage volume low.
This item is typically used to split the instrument signal going to a stage amp so a feed can be sent also to the mix board, or be used as a stand-alone instrument pre-amp. It is equipped with a ¼” jack for input, a 1/4" jack for output to a stage amp, one XLR jack for the send to the board and a TRS jack for inserting an FX device.Since this is an active D.I. box, it needs to be powered which can be done either with Phantom Power from the mix board, or with the supplied internal 9v battery. The battery is fairly easy to change by removing one screw in the bottom of the case.
|
The AD2022 is Avalon's fourth generation of fully discrete, symmetrical Pure Class A microphone preamplifiers. The dual mono AD2022 includes the original sonic capabilities and transparency of the M2, M22 and M5 preamplifiers plus several additional features, including selectable microphone source loading for optimized cable/mic matching, improved high-voltage Class A regulated power supplies, two high Z instrument inputs, variable-passive high pass filter, teflon/ silver wiring and doubled plated circuit boards for superior low level signal transfer. AD2022 FEATURES Symmetrical Pure Class A design, two channels Microphone and hi-Z instrument inputs Gain switched 4dB steps plus +/- 3dB fine output trim Selectable microphone input impedance matching Low noise -126dB EIN Ultra high quality, low-ratio, balanced input transformer Balanced, high-current Class A output to +36dB Large illuminated analog VU meters and twin peak LED's Regulated phantom power supply +48v Input polarity phase reverse High headroom +36dB input before overload Input -20dB pad for high level signals Sealed silver relays for all signal routing External AC 150w toroidal power chassis Fully discrete Class A regulated audio power supplies Deep, musical sound-stage, transparent amplification
MICROPHONE INPUT The AD2022 incorporates the most advanced high-performance microphone transformer available. Split low-ratio primary windings are carefully combined within a custom mu-metal core for extended smooth frequency response and very low distortion. Sealer silver relays are used for minimal signal invasion. The input signal selector, high pass filter, polarity-phase reverse, +48v power and the 20dB input attenuator all utilize local sealed relay operation. A variable passive high pass filter provides a minimum phase shift design while eliminating low frequency rumble, wind noise and mechanical vibration at sub sonic frequencies.
SYMMETRICAL PURE CLASS A DESIGN Two 100% discrete, high-voltage, symmetrical Pure Class A signal amplifiers are utilized per channel. The first operates in a cascaded-cascode FET configuration while the second stage amplifier is fully bipolar. The twin amplifiers share the total available gain requirement. This shared architecture increases the high level headroom capability, improves transient response and doubles the internal bandwidth of the ultra-high performance pure Class A signal amplifiers. OUTPUT and METERING High-current DC coupled, Class A discrete amplifiers are utilized for the output drive interface with +36dB capability into all known loads. Two large, high-quality analog VU meters indicate accurate signal readings while bi-color LED's offers peak indication at 0dB and +20dB.
AD2022 PREAMPLIFIER SPECIFICATIONS Circuit Topology: Twin cascode FET and bipolar low level signal amplifiers, high-voltage, 100% discrete, symmetrical Pure Class A Input Type and Load: Transformer balanced low-ratio, 50, 150, 600 and 1k5 ohm input load selection Maximum Mic Level: +36dB balanced XLR pin 2 hot (with -20dB passive attenuator) Maximum Instrument Level +18dB at 100k ohms instrument input level, standard mono 1/4 inch jack Input Attenuator: -20dB resistive pre transformer primary, sealed silver relay Phantom Power: +48v regulated 50mA capability, sealed silver relay High Pass Filter: Passive, variable from 30Hz to 185Hz @ 6dB per octave, sealed silver relay. Polarity Reverse: Sealed silver relay on microphone input Gain Range Input: +20dB to +64dB in 4dB steps Gain Output Range: +/- 3dB variable conductive plastic potentiometer Maximum Output Level: +36dB balanced 600 ohms, DC coupled, discrete symmetrical Pure Class A Output Type: XLR connector, pin 2 hot Noise EIN Unweighted: -126dB 150 ohm Noise 20kHz Unweighted: -102dB Distortion THD, IMD: 0.05% nominal Frequency Response -3dB: 1Hz to 120kHz transformer limit System Bandwidth: DC to 1MHz Output Meter: High quality, illuminated analog VU meter 0dB = +4dB. Peak Meter: Bi-color LED's 0dB and +20dB peak detection circuit. AC power supply B2T: External toroidal 100V to 240V, 50-60Hz selectable, 150 watts maximum. Cables: 90V ac, 4 pin male power input connector, B2T required, internal DC regulation Dimensions: 19 x 12 x 3.5 in (482 x 305 x 89mm) Weight: 15lbs (6.8kg) Dimensions - Shipping Carton: 24 x 21.5 x 7.5 in (610 x 546 x 190mm) Weight - Packed: 25lbs (11.4kg) |
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.