| Content | DAPAUDIO D1526 AGI-101 Audio Groundloop Isolator
Suppress nasty ground loops in your audio chain with this ground loop isolator. Now you can send undisturbed signals from your laptop, DVD player or other audio source through your amplifiers.
Specifications Housing diameter: 35mm
Cable length: 280 mm
Total length: 590 mm
|
Ενεργό DI box με ground lift, αναστροφή φάσης, έξοδους XLR και καρφί 1/4'' (thru), pad 3 θέσεων στην είσοδο για σήματα επιπέδου instrument/line/speaker
- Premium Performance
- Rugged Design
- Stackable Chassis with Durable Rubber Foot
- Gold-plated Neutrik® XLR Connector
- Premium Chrome Toggle Switches
- Hi-Z 1/4" Input Jack
- Parallel 1/4" Thru Jack
- Transformer Isolated
- Premium Shielded Custom dbx Transformer
- Balanced XLR Lo-Z Output
- 3-Way 0/20/40 dB Pad Switch
- Flat/High-Cut Filter Switch
- Output Polarity Invert Switch
- Ground Lift Switch
- 4 Year Warranty!
Additional dB12 Features - Phantom Powered
- Green LED Phantom Power Indicator
- +48V Phantom Operation
- Low-Noise Active Circuitr
dB12 Specifications INPUT SECTION
Input: 1 instrument/line/speaker level
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Impedance: 150k Ohm typical
Max Input Level: +20dBu (0dB pad)
+40dBu (20dB pad)
+60dBu (40dB pad)
OUTPUT SECTION
Thru Output: 1 parallel connection from input jack
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Main Output: 1 line level
Connector: XLR male jack
Type: Balanced
Impedance: 150 Ohm typical
Max Output Level: 0dBu
PERFORMANCE
Transformer: Custom dbx mu-metal-shielded
Frequency Response: 20Hz to 20kHz, +/-2.5dB
Noise: |
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
< 0,7 % bei 40 Hz
powering 9-V battery (IEC 6LF22) or
phantom power 24 ... 48 V.
inputs two 1/4" phone jacks , unbalanced
(one being used as output to instruments amp)
outputs XLR, balanced
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm |
The alphaton Direct Injection-Box SM-50 allows direct connection of electric guitars,
electric bass, and electronic music instruments with mixing desks of PA systems
and of recording studios.
The SM-50 reduces the amount of microphones used on stage, thus improving gain
before feedback.
Coloration of sound is avoided. Clean signal without interference from other instruments
eases the job of the recording engineer. The use of a strong aluminium die-cast box allows
trouble-free function for a number of years even under adverse conditions. Double grounding
(hum) can be eliminated by activating the built-in ground-lift switch. Isolation voltage between
input and output is 2500 volts, against ground 1500 volts (with ground-lift switch activated).
The box thus complies with toughest safety standards.
Technical Data
input impedance 20 kOhm
input impedance, instrument
input impedance, line-In
input impedance, speaker
output impedance 200 Ohm
frequency response 30 ... 20000 Hz, ± 1 dB
THD
isolation voltage tranformer pri/sec 2500 V
outpur to ground 1500 V
inputs 1/4" phone jacks, unbalanced
outputs XLR, balanced, microphone level.
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 230 g
dimensions113 x 71 x 37 mm
|
Palmer PAN 03
19" DI Box 4-Channel active
Active 4-channel DI box. Each channel has a jack input with a parallel output for passing through the signal. An attenuation switch (-30 dB) allows either a line or loudspeaker signal to be connected.Active 4 x DI box, 19" format. Technical specitications identicl to the PAN-02, however, the PAN-03 is built for mains operation. All connections and switches are located on the front panel, an additional parallel XLR output is located in back. 19 inch rack-mount format, 1 rack space, 90 mm front to back.
Product type
DI Boxes
Type
active
Channels
4
Inputs
4
Input connectors
6.3 mm jack
Max. input level
+ 45 dBu
Input impedance
(@ 60 Hz) 1 M Ohm(s)
Input pad
0 / -30 dB
Outputs
4 (+ 4 parallel XLR outs)
THRU outputs/channel
1
Output connectors
6.3 mm jack , XLR
Max. output level
+ 10 dBu
Output impedance
600 Ohm(s)
Frequency response
10 - 20000 Hz
Transformer balanced
Yes
Ratio
10 : 1
Indicators
Power
Controls
attenuator , ground lift
Operating voltage
external
Cabinet material
sheet steel
Cabinet surface
Powder coated
Width
480 mm
Width
19 "
Depth
90 mm
Height
45 mm
Height
1 U
Weight
1,6 kg |
Παθητικό DI box με ground lift, αναστροφή φάσης, έξοδους XLR και καρφί 1/4'' (thru), pad 3 θέσεων στην είσοδο για σήματα επιπέδου instrument/line/speaker
- Premium Performance
- Rugged Design
- Stackable Chassis with Durable Rubber Foot
- Gold-plated Neutrik® XLR Connector
- Premium Chrome Toggle Switches
- Hi-Z 1/4" Input Jack
- Parallel 1/4" Thru Jack
- Transformer Isolated
- Premium Shielded Custom dbx Transformer
- Balanced XLR Lo-Z Output
- 3-Way 0/20/40 dB Pad Switch
- Flat/High-Cut Filter Switch
- Output Polarity Invert Switch
- Ground Lift Switch
- 4 Year Warranty!
dB10 Specifications INPUT SECTION
Input: 1 instrument/line/speaker level
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Impedance: 150k Ohm typical
Max Input Level: +20dBu (0dB pad)
+40dBu (20dB pad)
+60dBu (40dB pad)
OUTPUT SECTION
Thru Output: 1 parallel connection from input jack
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Main Output: 1 line level
Connector: XLR male jack
Type: Balanced
Impedance: 150 Ohm typical
Max Output Level: 0dBu
PERFORMANCE
Transformer: Custom dbx mu-metal-shielded
Frequency Response: 20Hz to 20kHz, +/-2.5dB
Noise: |
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.