Content | DAPAUDIO D1526 AGI-101 Audio Groundloop Isolator
Suppress nasty ground loops in your audio chain with this ground loop isolator. Now you can send undisturbed signals from your laptop, DVD player or other audio source through your amplifiers.
Specifications Housing diameter: 35mm
Cable length: 280 mm
Total length: 590 mm
| Standard active DI box. Can be operated with 9 V batteries or 48 V phantom power. High-impedance input; higher output level than with a passive DI box. Active circuitry allows for high input impedance ( 1 meg. ohm) and higher input sensitivity (typical difference between in and out -4 dB). Maximum output impedance with phantom power operation +10 dB. Output: transformer balanced. The special "floating ground" circuitry enables ground lift even during phantom power operation. Metal case 110 x 73 x 42 mm. |
DOD AC 275 Active Direct Box with Switchable Ground Lift and Attenuator-2nd Hand- The AC 275 is an active, phantom powered direct box. Unlike a passive DI where the frequency response of the signal can be altered depending on the connected impedance, an active DI buffers the input signal with an amplifier. This assures that the sound source will reach the mixer balanced and noise-free. Housed in a cast alloy chassis, the AC 275 supplies two, high impedance, unbalanced 1/4" jacks and one low impedance balanced XLR jack. It operates with battery or phantom power.
|
The alphaton Direct Injection-Box SM-50 allows direct connection of electric guitars,
electric bass, and electronic music instruments with mixing desks of PA systems
and of recording studios.
The SM-50 reduces the amount of microphones used on stage, thus improving gain
before feedback.
Coloration of sound is avoided. Clean signal without interference from other instruments
eases the job of the recording engineer. The use of a strong aluminium die-cast box allows
trouble-free function for a number of years even under adverse conditions. Double grounding
(hum) can be eliminated by activating the built-in ground-lift switch. Isolation voltage between
input and output is 2500 volts, against ground 1500 volts (with ground-lift switch activated).
The box thus complies with toughest safety standards.
Technical Data
input impedance 20 kOhm
input impedance, instrument
input impedance, line-In
input impedance, speaker
output impedance 200 Ohm
frequency response 30 ... 20000 Hz, ± 1 dB
THD
isolation voltage tranformer pri/sec 2500 V
outpur to ground 1500 V
inputs 1/4" phone jacks, unbalanced
outputs XLR, balanced, microphone level.
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 230 g
dimensions113 x 71 x 37 mm
|
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic music instruments such as keyboards, synthesizers, electric and electronic pianos, etc. with mixing consoles in PA-systems and in recording studios. The SM-6 is designed for applications, where a passive DI-Box does not perfom satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone input section of the mixing desk. Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are not loaded or in any other way adversely affected. The voltage ratio from input to output is 1: 1 and is always sufficient for connection with any microphone input. Input connectors are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms, transformer balanced. The output level may in certain cases overload microphone inputs - the line input section of the mixing console must then be used for connecting the SM-6. The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm max. input impedance + 6 dBu, 1,55V ouptut impedance 600 Ohm frequency response 20 ... 20000 Hz, ± 0,2 dB gain 1 : 1 THD < 1 % at 30 Hz < 0,7 % bei 40 Hz powering 9-V battery (IEC 6LF22) or phantom power 24 ... 48 V. inputs two 1/4" phone jacks , unbalanced (one being used as output to instruments amp) outputs XLR, balanced pin 1 = ground, pin 2 = hot, pin 3 = cold case aluminium die-cast weight 240 g dimensions 113 x 71 x 37 mm | |
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.