Content | DAPAUDIO D1526 AGI-101 Audio Groundloop Isolator
Suppress nasty ground loops in your audio chain with this ground loop isolator. Now you can send undisturbed signals from your laptop, DVD player or other audio source through your amplifiers.
Specifications Housing diameter: 35mm
Cable length: 280 mm
Total length: 590 mm
|
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic music instruments such as keyboards, synthesizers, electric and electronic pianos, etc. with mixing consoles in PA-systems and in recording studios. The SM-6 is designed for applications, where a passive DI-Box does not perfom satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone input section of the mixing desk. Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are not loaded or in any other way adversely affected. The voltage ratio from input to output is 1: 1 and is always sufficient for connection with any microphone input. Input connectors are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms, transformer balanced. The output level may in certain cases overload microphone inputs - the line input section of the mixing console must then be used for connecting the SM-6. The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm max. input impedance + 6 dBu, 1,55V ouptut impedance 600 Ohm frequency response 20 ... 20000 Hz, ± 0,2 dB gain 1 : 1 THD < 1 % at 30 Hz < 0,7 % bei 40 Hz powering 9-V battery (IEC 6LF22) or phantom power 24 ... 48 V. inputs two 1/4" phone jacks , unbalanced (one being used as output to instruments amp) outputs XLR, balanced pin 1 = ground, pin 2 = hot, pin 3 = cold case aluminium die-cast weight 240 g dimensions 113 x 71 x 37 mm |
Παθητικό DI box με ground lift, αναστροφή φάσης, έξοδους XLR και καρφί 1/4'' (thru), pad 3 θέσεων στην είσοδο για σήματα επιπέδου instrument/line/speaker
- Premium Performance
- Rugged Design
- Stackable Chassis with Durable Rubber Foot
- Gold-plated Neutrik® XLR Connector
- Premium Chrome Toggle Switches
- Hi-Z 1/4" Input Jack
- Parallel 1/4" Thru Jack
- Transformer Isolated
- Premium Shielded Custom dbx Transformer
- Balanced XLR Lo-Z Output
- 3-Way 0/20/40 dB Pad Switch
- Flat/High-Cut Filter Switch
- Output Polarity Invert Switch
- Ground Lift Switch
- 4 Year Warranty!
dB10 Specifications INPUT SECTION
Input: 1 instrument/line/speaker level
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Impedance: 150k Ohm typical
Max Input Level: +20dBu (0dB pad)
+40dBu (20dB pad)
+60dBu (40dB pad)
OUTPUT SECTION
Thru Output: 1 parallel connection from input jack
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Main Output: 1 line level
Connector: XLR male jack
Type: Balanced
Impedance: 150 Ohm typical
Max Output Level: 0dBu
PERFORMANCE
Transformer: Custom dbx mu-metal-shielded
Frequency Response: 20Hz to 20kHz, +/-2.5dB
Noise: | Standard active DI box. Can be operated with 9 V batteries or 48 V phantom power. High-impedance input; higher output level than with a passive DI box. Active circuitry allows for high input impedance ( 1 meg. ohm) and higher input sensitivity (typical difference between in and out -4 dB). Maximum output impedance with phantom power operation +10 dB. Output: transformer balanced. The special "floating ground" circuitry enables ground lift even during phantom power operation. Metal case 110 x 73 x 42 mm. |
Ενεργό DI box με ground lift, αναστροφή φάσης, έξοδους XLR και καρφί 1/4'' (thru), pad 3 θέσεων στην είσοδο για σήματα επιπέδου instrument/line/speaker
- Premium Performance
- Rugged Design
- Stackable Chassis with Durable Rubber Foot
- Gold-plated Neutrik® XLR Connector
- Premium Chrome Toggle Switches
- Hi-Z 1/4" Input Jack
- Parallel 1/4" Thru Jack
- Transformer Isolated
- Premium Shielded Custom dbx Transformer
- Balanced XLR Lo-Z Output
- 3-Way 0/20/40 dB Pad Switch
- Flat/High-Cut Filter Switch
- Output Polarity Invert Switch
- Ground Lift Switch
- 4 Year Warranty!
Additional dB12 Features - Phantom Powered
- Green LED Phantom Power Indicator
- +48V Phantom Operation
- Low-Noise Active Circuitr
dB12 Specifications INPUT SECTION
Input: 1 instrument/line/speaker level
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Impedance: 150k Ohm typical
Max Input Level: +20dBu (0dB pad)
+40dBu (20dB pad)
+60dBu (40dB pad)
OUTPUT SECTION
Thru Output: 1 parallel connection from input jack
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Main Output: 1 line level
Connector: XLR male jack
Type: Balanced
Impedance: 150 Ohm typical
Max Output Level: 0dBu
PERFORMANCE
Transformer: Custom dbx mu-metal-shielded
Frequency Response: 20Hz to 20kHz, +/-2.5dB
Noise: |
Passive DI box especially designed for guitars.
The PDI09 can be connected between an effect device or amplifier and the mixing console. The PDI09 is not suitable for direct connection to a guitar. Integrated filter circuits simulate the authentic "speaker" sound. Tone can be varied between "Mellow“, "Normal“, or "Bright“.
Technical specifications:
- Input: 6.3 mm jack with parallel "THRU" socket
- Output: male XLR transformer balanced
- Attenuator: (Level switch) 0 dB for line signals, -15 dB for small amps up to 10 w, 30 dB for large amps up to 200 w
- No battery necessary
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.