| Content | Το D&R Hybrid-1 είναι ένα αναλογικό τηλεφωνικό υβρίδιο, με δυνατότητα ελέγχου τοπικά. Δεν απαιτεί εξωτερική τροφοδοσία ρεύματος καθώς τροφοδοτείται από την τηλεφωνική γραμμή.
- είσοδος και έξοδος ήχου(jack 6,3 χιλ.)
-Υποδοχή 2 καλωδίων με παράλληλη έξοδο για σύνδεση εξωτερικής τηλεφωνικής συσκευής.
-Τοπικός έλεγχος των λειτουργιών αποδοχής-απόρριψης γραμμής και ειδοποίηση εισερχόμενης κλήσης.
-Αυτόματη αντιστάθμιση επιπέδου γραμμής
-Έλεγχος στάθμης σήματος αποστολής/λήψης στο εμπρόσθιο τμήμα
-Τροφοδοτούμενο από την τηλεφωνική γραμμή
-Εσωτερικό buzzer on/off
- 1U Πλαίσιο 1/2
D&R's newest Telephone Hybrid-1 is an interface between a standard telephone line and a mixing console. Its purpose is to enable to record or broadcast a conversation between a caller and a presenter in an easy way.
Superb audio separation between in and outgoing signals are achieved by carefully designed internal circuitry. It is a problem solver for changing two wire communication into a four wire system with separate in and outputs.
Telephone hybrids provide the interface between professional audio equipment and the public telephone network.
They provide protection for your equipment and the public telephone lines, allowing for varying line signals and line conditions. Automatically canceling out the unwanted signal they also facilitate two-way communication down a single telephone line.
Each hybrid has a telephone line connection, a handset connection and separate connectors for audio input and output from a broadcast mixer, or other professional audio source.
A large proportion of D&R hybrids are used in radio and television broadcasting applications allowing external callers to be connected to the studio mixing console. Most of the other units are supplied to communication operations allowing extremely effective conversion between 4-wire audio circuits and standard telephone lines.
Specification
Output: balanced mic level -20dB. Input: Line level 0 dBu balanced. R/C balance: fully adjustable separation to more than 30dB.
C-BALANCE :12 pole rotary switch to select the optimum side tone attenuation.
R-BALANCE: Internal potentiometer to adjust for optimum side tone attenuation.
TO CALLER: Switch to temporarily connect the line (wall) connector to the Phone connector (appliance) to be able to dial and make a connection.
ON-LINE CONNECT: Line connect switch to connect and disconnect calls from the telephone line |
Features
Four Independent Compressor Channels
Channels 1 and 2, 3 and 4 are stereo linkable
7 LED Gain Reduction metering
Balanced XLR Inputs and Outputs
Sidechain Insert points
Intuitive, user friendly layout
Flawless performance
The sheer amount of effects and signal processors necessary for today's standards
of audio production puts a great strain on the available space in equipment racks,
both in the studio and on the road.So, ARX would like to introduce the ARX Quadcomp.
An all-new upgrade of the classic award-winning ARX Quadcomp?, the very first four
channel 1 RU compressor.You?ll notice that we haven?t strayed very far from our
original design concept. The Quadcomp is still four variable ratio Compressor/ Limiters
neatly housed in a compact all steel 1 RU package. However, all new low noise/low
distortion circuitry, better metering plus XLR inputs and outputs put the Quadcomp
in a class of its own.
More Control, Less Space
On the front panel, each channel has the 'industry standard' individual controls for Threshold,
Compression Ratio and Output, plus a new 7 LED Gain Reduction display for accurate visual
indication of the amount of gain reduction being applied to the program, and an IN/OUT
hardwire bypass switch.In addition to this, each channel has a blank numbered panel to write
on for easy confirmation of compressor assigns.
Precision Circuitry
Internally, each compressor uses Class A VCAs and true 2 pole averaging RMS/DC converters
for low distortion and accuracy, plus program dependent attack and release time, which
automatically determines optimum compressor response.
Balanced Inputs and Outputs
The rear panel has true differential Balanced XLR Inputs and Outputs for each compressor.
Each compressor has a TRS jack Sidechain access insert point, for frequency sensitive
compression, De-essing, etc. in conjunction with an external equalizer (such as the ARX EQ260).
Compressor pairs 1 and 2, 3 and 4 also have rear panel mounted Stereo Link switches for accurate
stereo tracking. When switched IN, the first channel becomes the master and controls all the functions
of the second except Output gain.
Universal AC Power
AC power range is switchable 100 to 120V, or 220 to 240V, and is connected to the unit via
a standard IEC connector, with built-in fuse and voltage switch.
Whatever the application ? Channel insert, Bus insert, Master Outputs, Monitor outputs,
Crossover outputs, the Quadcomp II?s unique High Density design, precision Low Noise circuitry
and clean uncluttered layout make it a truly useful audio tool for all applications.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance
Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 20dB
CMRR >50dB, 20 Hz?20 KHz
Output Impedance
Balanced 300 ohms Unbalanced 150 ohms
Output Level (Max) + 20 dB
Frequency Response 20Hz-20KHz ±0.5dB
Signal to Noise ratio
-93 dB Unweighted, -98 dB ?A? weighted
Distortion .015% THD @ 0dB,1KHz
Dynamic Range 108 dB
Attack and Release Times Program dependent
Metering
7 LED display: ?1, 2, 3, 6, 12, 18, ?24 dB
Sidechain Insert Impedance 10 Kohm
Power Requirements
100/120 V AC or 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions
19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input Connector type Balanced XLR
Output Connector type Balanced XLR
Sidechain Insert Connector TRS Jack
Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
7 LED Gain Reduction display
Marker panel for labelling compressor assigns
Stereo link status LEDs
Rear Panel Connectors
Input and Output balanced XLR connectors
TipRingSleeve Sidechain insert connectors
Channels 1 and 2, 3 and 4 Stereo link switches
IEC AC mains connector with inbuilt fuse and
voltage change |
The Multicom Pro-XL MDX4600 gives you 4 channels of first-class dynamic
control in a single rack space. With a multitude of new features like the
advanced program-adaptive expander gate, extensive metering plus a variety
of configuration options, the Multicom Pro-XL puts a lot of dynamic processing
power in your rack.
Features
Switchable IKA (Interactive Knee Adaptation) program-adaptive compression
circuitry combines the advantages of hard-knee and soft-knee characteristics
IRC (Interactive Ratio Control) expander/gate circuitry for virtually inaudible noise
suppression
Switchable dynamic enhancer for brilliant, lively audio even with heavy compression
IGC (Interactive Gain Control) peak limiting circuitry combines clipper and program
limiter for reliable and inaudible protection against signal peaks
Switchable low contour filter prevents "pumping" due to low-frequency dominated
compression
Stereo couple function selectable for channels 1/2 and 3/4
Ultra low-noise 4580 operational amplifiers and state-of-the-art THAT¬ VCA's
Separate 8-segment LED meters for input/output levels and gain reduction
Selectable operating level (+4 dBu/-10 dBV)
High-quality detented ALPS¬ potentiometers and illuminated switches
Servo-balanced inputs and outputs with ? in. TRS and gold-plated XLR
connectors
Manufactured under ISO9000 certified management system
|
The Avalon VT-737SP features a combination of TUBE preamplifiers,
opto-compressor,sweep equalizer, output level and VU metering in a
2U space.
PREAMPLIFIER
The VT-737SP has three input selections: 1. The VT-737SP features a
higher-performance microphone input transformer with +48v phantom
selection. 2. Instrument DI high source input with jack located on front
panel. 3. Balanced line input, discrete high-level Class A. The Class A
preamplifier utilizes two cascaded, dual vacuum tube triodes configured
with minimum negative feedback. A high gain switch boosts the overall
gain of the preamplifier. The four high quality tubes are configured as
singled ended anode coupled followers. A passive-variable high pass filter
and hard-wire relay bypass completes the input signal conditioning. The
phase reverse relay is available on all three inputs.
OPTO-COMPRESSOR
The opto-compressor features a minimum signal path design with twin Class
A vacuum tube triodes for gain matching. The optical attenuator acts as a
simple passive level controller. Full dynamic control from soft compression to
hard- knee limiting can be achieved with threshold, ratio-compression, attack
and release controls plus gain reduction selection on the large VU meter. Special
spectral control including de-ess is available with the dual sweep mid EQ to side-
chain switch. The EQ section can be flipped pre or post the opto-compressor
via a front panel switch for alternate effects and tone shaping. Two VT-737SPs
can be linked via a rear panel link cable for stereo tracking. The compressor
bypass is a sealed silver relay for the most direct signal path.
SWEEP-EQUALIZER AND OUTPUT LEVEL
The VT-737SP equalizer utilizes 100% discrete, Class A-high-voltage transistors
for optimum sonic performance. The high and low frequency bands provide the
smooth characteristics of an all passive design, while the dual mid bands include
variable frequency and switched Q-width selection. The enhanced range of the mid
bands is extended into the high and low bands by the use of X10 frequency multipliers.
The bypass switch incorporates a sealed silver relay for the most direct signal path.
When the EQ to sidechain is engaged, the high-low EQ remains in the audio path for
"tone enhancement“. The output level control provides a variable control of the overall
signal path. The output amplifier utilizes another dual triode vacuum tube driving a
100% discrete, Class A, high-current, balanced and DC coupled low noise output
amplifier. AVALON VT-737SP FEATURES
Vacuum tube triode signal path, transformer balanced microphone input, high-voltage
circuits for maximum headroom to +30dB, low noise -92dB, internal discrete power
supply with toroidal transformer, soft-start tube life extender, stereo link for compressors,
all discrete Class A equalizer with musical passive filter design, sealed silver relays for
signal routing, large control knobs with professional conductive plastic potentiometers,
VU meter for output level monitoring and compressor gain reduction. VT-737SP SPECIFICATIONS
Circuit topology Four dual triode vacuum tubes (Sovtek 6922), high-voltage discrete
Class A
Gain Range Microphone: Transformer balanced 850/2500 ohm, 0dB to +58dB Instrument:
Unbalanced 1 meg ohm, 0dB to+30dB Line: Balanced Class A 20k ohms, -27dB to 28dB
Maximum input level and connector types Microphone26dB@25Hz, +30dB@1kHz balanced
XLR Instrument+30dB unbalanced front panel jack socket
Line +36dB balanced XLR
Maximum output level +30dB balanced 600 ohms, DC coupled, discrete Class A
Output type and gain XLR connector, output trim gain -45dB to20dB
Noise 20kHz unweighted -92dB
Noise microphone EIN -116dB, 22Hz to 22kHz unweighted
Distortion THD, IMD 0.5%
Frequency response -/2.5dB 10Hz to 120kHz input filter included
Frequency response -3dB 1Hz to 200kHz line in-out
VU meter and gain reduction High quality illuminated OVU =+4dB and gain reduction to -20dB
High cut filter Variable 6dB per octave 30Hz to 140Hz
Compressor type Optical passive attenuator incorporating twin vacuum tubes and stereo link
Threshold - Ratio Threshold variable -30dB to +20dB, ratio-compression variable 1:1 to 20:1
Attack - Release Attack variable 2mS to 200mS, release variable 100mS to 5 seconds
Equalizer type Discrete Class A, variable active and switched passive design
Frequency bands (4) Treble - switched 10kHz, 15kHz, 20kHz, 32kHz, +/- 20dB range, shelf
High mid - variable 200Hz to 2k8Hz and 2kHz to 28kHz, +/- 16dB range, hi-lo Q Low mid -
variable 30Hz to 450Hz and 300Hz to 4k5Hz, +/- 16dB range, hi-lo Q Bass - switched 15Hz,
30Hz, 60Hz, 150Hz, +/- 24dB range, shelf
AC power Internal toroidal 100v to 240v, 50-60Hz selectable, 75 watts maximum
Dimensions 19 x 12 x 3.5 in (482 x 305 x 89mm)
Weight 22lbs (10kg)
Dimensions-shipping carton 21 x 18 x 8 in (533 x 457 x 203mm)
Weight-packed 26lbs (11.8kg)
|
Μονοκάναλο feedback destroyer (αντιμικροφωνικό) με ενσωματωμένο προενισχυτή μικροφώνου, delay line, noise gate και compressor. Ανιχνεύει αυτόματα τους μικροφωνισμούς και τους εξαφανίζει. Διαθέτει επίσης low cut filter, phantom power, balanced in/out.
Χαρακτηριστικά:
Μονοκάναλο feedback destroyer (αντιμικροφωνικό) με ενσωματωμένο προενισχυτή μικροφώνου, delay line, noise gate και compressor
Αυτόματα ανιχνεύει και εξολοθρεύει 8 συχνότητες μικροφωνισμών
Ultra low noise mic/line είσοδος με gain control και +48V phantom power τροφοδοσία για πυκνωτικό μικρόφωνο
Delay line μέχρι 2,5 sec και με ρύθμιση μέτρων ποδιών και msec
Noise gate με αυτόματες και manual ρυθμίσεις
Αυτόματο compressor
Low cut filter με ρύθμιση συχνότητας
Είσοδος – έξοδος σε balanced JACK 6,35 και XLR
Frequency response: 10H – 21KHz
Noise: 92dB (line), 89dB mic
THD: 0.007%
Μετατροπείς: 24bit Sigma-Delta, 64/128-times oversampling
Η συσκευασία περιλαμβάνει: fbq100, users manual
Τροφοδοσία: AC 220V / 50Hz
Διαστάσεις: 56 x 88 x 132 mm
Βάρος: 380 gr
|
Features
Enhance switch to restore spectral balance of compressed signal
Switchable Mode - Dual Channel or Stereo linked
Above or Below Threshold LEDs
Balanced XLR and Jack Inputs and Outputs
Intuitive, user friendly layout
Flawless performance
Innovation
The ARX COMPO? is a unique compressor/limiter designed for use in any
professional audio dynamics control application, packaged in a compact 1
RU chassis.The COMPO operates as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain controls.
A Stereo Link switch on the front panel lets both channels track as a stereo
pair in a Master/Slave configuration.
Enhance Switch
The COMPO features an 'Enhance' switch, which provides frequency restoration
to preserve the spectral balance of the audio signal, compensating for the sagging
Low and High frequency response of compressed program material.
The best way to think of it is as a 'smart' loudness control.
Wide Scale metering
There is comprehensive LED indication of all operating functions and status. Above
or Below Threshold LEDs on each channel give you instant visual confirmation of
compressor activity, as well as easy to read LED Gain Reduction meters.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. Other features include an Active/Bypass
switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
ARX Quality
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the ARX COMPO is the
ideal installation 'set and forget' compressor, and is also equally at home in Studio,
Broadcast and Sound Reinforcement environments.
Every day, ARX Audio interface products solve audio problems for thousands of people
around the world.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.4dB
Signal to Noise ratio -85 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 107 dB
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack
Front Panel Controls
Channel A Active/Bypassed IN/OUT switch
Threshold, Ratio and Output Gain controls
Numbered marker panel for labelling compressor assigns
5 segment LED Gain Reduction display
Above/Below Threshold status LEDs
Enhance switch and status LED
Stereo link switch and status LED
Channel B controls identical to Channel A
Rear Panel Connectors
Balanced XLR Input and Output connectors.
Balanced TRS jack Input and Output connectors.
AC input connector, with voltage switch and fuse.
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.