| Content | Το D&R Hybrid-1 είναι ένα αναλογικό τηλεφωνικό υβρίδιο, με δυνατότητα ελέγχου τοπικά. Δεν απαιτεί εξωτερική τροφοδοσία ρεύματος καθώς τροφοδοτείται από την τηλεφωνική γραμμή.
- είσοδος και έξοδος ήχου(jack 6,3 χιλ.)
-Υποδοχή 2 καλωδίων με παράλληλη έξοδο για σύνδεση εξωτερικής τηλεφωνικής συσκευής.
-Τοπικός έλεγχος των λειτουργιών αποδοχής-απόρριψης γραμμής και ειδοποίηση εισερχόμενης κλήσης.
-Αυτόματη αντιστάθμιση επιπέδου γραμμής
-Έλεγχος στάθμης σήματος αποστολής/λήψης στο εμπρόσθιο τμήμα
-Τροφοδοτούμενο από την τηλεφωνική γραμμή
-Εσωτερικό buzzer on/off
- 1U Πλαίσιο 1/2
D&R's newest Telephone Hybrid-1 is an interface between a standard telephone line and a mixing console. Its purpose is to enable to record or broadcast a conversation between a caller and a presenter in an easy way.
Superb audio separation between in and outgoing signals are achieved by carefully designed internal circuitry. It is a problem solver for changing two wire communication into a four wire system with separate in and outputs.
Telephone hybrids provide the interface between professional audio equipment and the public telephone network.
They provide protection for your equipment and the public telephone lines, allowing for varying line signals and line conditions. Automatically canceling out the unwanted signal they also facilitate two-way communication down a single telephone line.
Each hybrid has a telephone line connection, a handset connection and separate connectors for audio input and output from a broadcast mixer, or other professional audio source.
A large proportion of D&R hybrids are used in radio and television broadcasting applications allowing external callers to be connected to the studio mixing console. Most of the other units are supplied to communication operations allowing extremely effective conversion between 4-wire audio circuits and standard telephone lines.
Specification
Output: balanced mic level -20dB. Input: Line level 0 dBu balanced. R/C balance: fully adjustable separation to more than 30dB.
C-BALANCE :12 pole rotary switch to select the optimum side tone attenuation.
R-BALANCE: Internal potentiometer to adjust for optimum side tone attenuation.
TO CALLER: Switch to temporarily connect the line (wall) connector to the Phone connector (appliance) to be able to dial and make a connection.
ON-LINE CONNECT: Line connect switch to connect and disconnect calls from the telephone line |
Features
Enhance switch to restore spectral balance of compressed signal
Switchable Mode - Dual Channel or Stereo linked
Above or Below Threshold LEDs
Balanced XLR and Jack Inputs and Outputs
Intuitive, user friendly layout
Flawless performance
Innovation
The ARX COMPO? is a unique compressor/limiter designed for use in any
professional audio dynamics control application, packaged in a compact 1
RU chassis.The COMPO operates as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain controls.
A Stereo Link switch on the front panel lets both channels track as a stereo
pair in a Master/Slave configuration.
Enhance Switch
The COMPO features an 'Enhance' switch, which provides frequency restoration
to preserve the spectral balance of the audio signal, compensating for the sagging
Low and High frequency response of compressed program material.
The best way to think of it is as a 'smart' loudness control.
Wide Scale metering
There is comprehensive LED indication of all operating functions and status. Above
or Below Threshold LEDs on each channel give you instant visual confirmation of
compressor activity, as well as easy to read LED Gain Reduction meters.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. Other features include an Active/Bypass
switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
ARX Quality
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the ARX COMPO is the
ideal installation 'set and forget' compressor, and is also equally at home in Studio,
Broadcast and Sound Reinforcement environments.
Every day, ARX Audio interface products solve audio problems for thousands of people
around the world.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.4dB
Signal to Noise ratio -85 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 107 dB
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack
Front Panel Controls
Channel A Active/Bypassed IN/OUT switch
Threshold, Ratio and Output Gain controls
Numbered marker panel for labelling compressor assigns
5 segment LED Gain Reduction display
Above/Below Threshold status LEDs
Enhance switch and status LED
Stereo link switch and status LED
Channel B controls identical to Channel A
Rear Panel Connectors
Balanced XLR Input and Output connectors.
Balanced TRS jack Input and Output connectors.
AC input connector, with voltage switch and fuse.
|
VIRTUALIZER 3D FX2000 - Υψηλής απόδοσης 3D Multi-Engine Επεξεργαστής εφέ.
• 71 breathtaking new algorithms—true RSM (Real Sound Modeling) stereo and 3D effects
• Wave-adaptive virtual Room reverb algorithms for natural reverb and delay
• Awesome modulation, dynamic, psychoacoustic and EQ algorithms
• Authentic amp simulation, distortion and special effects
• 11 effect combinations with selectable serial / parallel configuration
• Up to 7 adjustable parameters plus 2-band EQ per effect
• 24-bit A/D and D/A converters with 64/128-times oversampling
• True stereo processing for realistic channel separation in stereo image
• 100 factory presets plus 100 user memory locations
• Extensive MIDI implementation
• Accurate LED level meters for perfect level setting and optimum performance
• Servo-balanced XLR and ¼'' TRS inputs and outputs
The FX2000 allows you to layer modulation effects like chorus, flanger, pitch or tremolo with your reverb or delay selections.
The FX2000 provides 12 different reverb programs, so you always have the ideal reverb for your live performance or studio needs.
• Reverbs: Cathedral - Gold plate - Small hall - Studio - Concert - Stage - Spring & Reverse Reverb - Ambience and more...
• Delays: Stereo - Tape Echo - Ping Pong and more...
• Modulation and Pitch Shifter FX: Stereo/Vintage/Jet Stream Flanger - Stereo/Analog/Vintage/Ultra/ Chorus - Stereo/Vintage/Dual Phaser - Rotary - Pitch Shifter - Vibrato and more...
• Dynamic FX: Compressor – Expander – Gated Reverb – An. Compr/Lim. — Ultramizer – Denoiser – De-Esser and more...
• Psychoacoustic FX: Exciter – Enhancer – Stereo Imager and more...
• Filter/EQ FX: Auto/LFO Filter – Parametric/Graphic EQ.
• The FX2000 is also equipped with distortion, amplifier and speaker simulation including Vocal/Tube distortion, Guitar Amp and more...
• Special FX:Vinylizer - Sampler - Vocoder - Voice Canceler - Resonator.
|
Μονοκάναλο feedback destroyer (αντιμικροφωνικό) με ενσωματωμένο προενισχυτή μικροφώνου, delay line, noise gate και compressor. Ανιχνεύει αυτόματα τους μικροφωνισμούς και τους εξαφανίζει. Διαθέτει επίσης low cut filter, phantom power, balanced in/out.
Χαρακτηριστικά:
Μονοκάναλο feedback destroyer (αντιμικροφωνικό) με ενσωματωμένο προενισχυτή μικροφώνου, delay line, noise gate και compressor
Αυτόματα ανιχνεύει και εξολοθρεύει 8 συχνότητες μικροφωνισμών
Ultra low noise mic/line είσοδος με gain control και +48V phantom power τροφοδοσία για πυκνωτικό μικρόφωνο
Delay line μέχρι 2,5 sec και με ρύθμιση μέτρων ποδιών και msec
Noise gate με αυτόματες και manual ρυθμίσεις
Αυτόματο compressor
Low cut filter με ρύθμιση συχνότητας
Είσοδος – έξοδος σε balanced JACK 6,35 και XLR
Frequency response: 10H – 21KHz
Noise: 92dB (line), 89dB mic
THD: 0.007%
Μετατροπείς: 24bit Sigma-Delta, 64/128-times oversampling
Η συσκευασία περιλαμβάνει: fbq100, users manual
Τροφοδοσία: AC 220V / 50Hz
Διαστάσεις: 56 x 88 x 132 mm
Βάρος: 380 gr
|
Innovation
The ARX AFTERBURNER? is a unique Multi Mode compressor/limiter
designed for use in any professional audio dynamics control application.
Multiple Modes
The Afterburner can be set up and used in three different ways:
In Two channel mode, it performs as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain. In stereo
mode, our New Adaptive Stereo Link circuitry provides increased stereo
imaging accuracy when linking both channels as a stereo pair. A single front
panel switch puts the Afterburner into its alternative Mono mode, setting it up
as a Single channel, Dual Band compressor/limiter, with separate dynamics
control of both Low and High frequencies, opening up a whole new range of
gain control techniques.
Enhance Switch
In any mode, the Afterburner features an 'Enhance' switch, which provides
frequency restoration to preserve the spectral balance of the audio signal,
compensating for the sagging Low and High frequency response of compressed
program material. Think of it as a 'smart' loudness control.
Features
Switchable Modes - Stereo; Dual Channel Single band; or Single Channel
Dual Band (Low and High)
Low and High frequency compression in Single Channel mode
'Enhance' switch restores spectral balance of compressed signal
New Hard/Soft knee compression switch
New Adaptive Stereo Link circuit for accurate stereo imaging
New Above/Below Threshold LEDs enable at-a-glance compression
confirmation
Balanced XLR and Jack Inputs and Outputs
Sidechain Insert points
Intuitive user-friendly layout
Flawless performance
New Above/Below Threshold LEDs enable at-a-glance compression confirmation
New Hard or Soft knee compression option
New LED metering provides accurate Level status, with separate Gain Reduction
metering in easy to read 'wide scale' meters. There is also comprehensive LED
indication of all operating functions and status in any mode.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. As well, each channel has a TRS jack
Sidechain access insert point, for applications such as De-essing (when used with
an external equalizer such as the ARX Multi Q or EQ 260).Other features include a
true Hardwire bypass switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the unique ARX Afterburner
is equally at home in Studio, Installation, Broadcast and Sound Reinforcement
environments. It can provide great sounding dynamics control effects that are not
available with any other device.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise ratio -93 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 115 dB
Sidechain Insert Impedance 10 Kohm
Filter Section
Filter Type Phase corrected 6dB/octave
Summed Filter Response ±0.2dB through crossover region
Dividing Frequency 250 Hz
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack
Sidechain Insert Connector TRS Jack
Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
Above/Below Threshold LEDs
12 segment LED Output Level display
Numbered marker panel for labelling compressor assigns
7 segment LED Gain Reduction display
Enhance switch and status LED
Adaptive Stereo link switch and status LED
Dual/Single channel mode switch and status LEDs
Rear Panel Connectors
Balanced Inputs and Outputs, on both XLR and TRS jack
connectors. In Single channel (Mono) mode, use Channel
1 Inputs and Outputs only
Sidechain Insert TRS connector on each channel
AC input connector, with voltage switch and fuse.
|
The S com 4 is a compact and versatile single-rack space device that provides
four channels of high quality dynamics processing with an Expander/Gate and
Compressor/Limiter on each channel.
The four channels operate independently or in stereo pairs. Its multi-segment LED
metering displays input/output level as well as gain reduction. The Expander/Gate
section features a continuously variable Threshold control as well as a switch for
fast or slow release times.
The Compressor/Limiter section includes variable Threshold, Ratio and Output levels.
S com 4's Enhancer switch restores high frequencies that are sometimes diminished
by heavy compression. This wide-ranging combination of features makes the S com
4 an efficient and versatile audio tool for a wide variety of applications. Its clean and
quiet audio characteristics make it ideal where high sonic integrity is imperative.
FEATURES:
4 Channel Compressor/Limiter, Expander/Gate with Enhancer
Linkable in two Stereo pairs
Expander/Gate with variable Trigger control and switchable Fast/Slow Release
5 Segment LED meters for Input/Output levels and Gain Reduction on each channel
Advanced circuit design utilizing Low Noise Operational
Amplifiers and High Quality VCA's
Servo Balanced Inputs and Outputs on XLR and 1/4" connectors
SKD (Smart Knee Detector) circuit automatically switches from soft to hard knee
based on the level of Input signal applied
Individual Threshold and Ratio controls on each channel
Three-year extended warranty
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.