LAB GRUPPEN iP900 2X300W POWER AMPLIFIER

The iP 900 is a space-saving power amplifier, ideal for use in installations
as well as in cost-effective live sound systems.
The Iron Power (iP) family of power amplifiers is the new compact and versatile
line of professional power amplifiers with classic toroidal iron transformers.
To achieve a compact design, the latest semiconductor technology is utilized.
This, together with Lab.gruppen?s proprietary copper cooling system, Intercooler?,
enhances the 2 ohms capacity. A new Bi-phase wiring scheme also increases
the capacity of the power supply. This extends the power bandwidth in the low end.

Key Features:
2 x 200 watts @ 8 ?
2 x 320 watts @ 4 ?
2 x 470 watts @ 2 ?
(Measured just below clip level, with both channels driven)
Compact design: 2U high
Intercooler? cooling system with front-to-rear airflow
Multiple positions gain switch
Easily accessible dust filter
Improved low-end power bandwidth
Neutrik Combo jack and Phoenix terminal block input connectors
Bridged mono outputs in one SpeakOn connector

Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of
features to make the iP family functional in all situations from installation to cost-effective
live sound systems:

Multiple positions Gain switch
To meet the demands for a flexible gain structure in the system, Lab.gruppen offers a
multiple position gain switch. The maximum amplifier gain can be set to all industry
standards: 20, 23, 26, 29, 32, 35, 38 and 41 dB.

Versatile input connection
With the Neutrik Combo-jack we offer both the professional XLR-type standard and the
semi-pro 1/4? TRS phono-jacks. For installations the 3-pin Phoenix terminal block may
be handier.

Soft Start
Toroidal transformers require a huge amount of start current to build up a magnetic flux
when the amplifier is switched on. Therefore Lab.gruppen have included a soft start circuit
to minimize the risk of blowing the wall fuse and to reduce flickering in the lighting.

Sophisticated protection circuitry, combining:
ALS? short circuit protection; the Adaptive Limiting System permits very high peak currents,
but keeps the amplifier within the Safe Operation Area.
DC protection; protects against infrasonic signals
VHF protection; protects the loudspeakers against strong very high frequency non-musical signals
above the audible range.
Thermal protection; prevents the amplifier from being overheated. The protection indicators on
the front panel are switched on, as a warning, before the protection process is initiated.
AC protection; shuts down the power supply if the line voltage is outside the operating voltage.
Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining
full peak power.

Power Output Level R-150 PLUS

STEREO
8ohm(T.H.D 0.05%)  50W+50W
4ohm(T.H.D 0.05%)  75W+75W

BRIDGED MONO
8ohm(T.H.D 0.05%)  50W
8ohm(T.H.D 0.5%)  170W

Frequency Response 20Hz- 20kHz, ±0.5dB

Convection Cooled

SoftStart Protection System

Balanced 10kΩ@0.775V Inputs

XB Series - Intelligent Power

Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XB 800:  2x 400 W @ 4 Ohm
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.025%
Signal-to-Noise Ratio:  < 103 dB
Channel Seperation:  > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  500 @ 4 Ohm
Cooling:  2x fan (temp. reg. variable speed)
Weight: 13 kg/(29 lbs)                                 
Dimensions:  2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)

Τελικός ενισχυτής 1U ισχύος 2 Χ 150 Watt/4Ω με απόκριση συχνότητας 20Hz - 20KHz. Βάρος 11 Kg. Διαθέτει ρύθμιση ευαισθησίας εισόδου (0,775V/1,0V/1,44V), Limiter και φίλτρα Low pass & High pass για σύνδεση με sub ή δορυφόρο. Διαθέτει εισόδους balanced XLR/JACK και εξόδους ηχείων σε Speakon & Binding post.

Νέας γενιάς τελικός επαγγελματικός ενισχυτής υψηλών απαιτήσεων. Παρέχει μεγάλη ισχύ εξόδου και υψηλή ποιότητα ήχου.  Χρησιμοποιώντας την επόμενης γενιάς τεχνολογία EEEngine, ο ενισχυτής έχει έως 40% μεγαλύτερη απόδοση και χαμηλότερη εκπομπή θερμότητας από συμβατικές τεχνολογίες ενισχυτών. Έχει διπλούς ανεμιστήρες ψύξης με αυτόματα ρυθμιζόμενη ταχύτητα για απόλυτη ψύξη. Διαθέτει θήρα για σύνδεση σε ψηφιακό δίκτυο CobraNet και θύρα για σύνδεση και έλεγχο λειτουργίας με surveillance system. Απόκριση συχνότητας 10 Hz – 40 KHz. Ισχύς 2 x 250 Watt / 8Ω RMS, 2 x 450 Watt / 4Ω RMS, 900 Watt / 8Ω bridge RMS. Βάρος 12,5 κιλά.

HPS 1500 is a 2 channel power amplifier that delivers up to 2 x 750 W RMS @ 4 Ω (1500 W RMS bridged @ 8 Ω).

XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.
A forced air cooling system maintains a low operating temperature.