LD Premium LDSP46K 4-Channel Power Amplifier The LDSP46K is a no-compromise 4-channel power amplifier providing professional performance and versatility in a compact switch mode power supply Class H design. With a massive output of 4x 1.440W into 2Ohms and 2x 2.880 in 4Ohms stereo bridge mode it is an extremely efficient solution for touring and […]
The LDSP46K is a no-compromise 4-channel power amplifier providing professional performance and versatility in a compact switch mode power supply Class H design. With a massive output of 4x 1.440W into 2Ohms and 2x 2.880 in 4Ohms stereo bridge mode it is an extremely efficient solution for touring and installation sound reinforcement weighing in at a mere 8.6kg.
Consistent operation is ensured by the heavy duty construction with high quality components and comprehensive protection circuitry including soft start with turn-on muting, PMS™ power management, SSP™ (Safe operation Sentry Protection) and ICL™ Intelligent Clip Limiting to maintain signal integrity. Protection circuits against DC, thermal and power supply overload are implemented. A switchable subsonic filter and a 3-position gain switch offer variable amplifier adjustment.
The LDSP46K features a full 20Hz – 20kHz bandwidth with low THD and crosstalk, a damping factory higher than 500, excellent S/N ratio and 3 selectable gain/sensitivity levels.
Protection: Soft-start, Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short circuit, Open or mismatched loads, Overloaded power supply, ICL Clip Limiter, PMS, SSP
Controls: On/Off, Volume, Voltage Gain, Dual / Link switchable, Bridge / Stereo configuration switch
The LDSP46K is a no-compromise 4-channel power amplifier providing professional performance and versatility in a compact switch mode power supply Class H design. With a massive output of 4x 1.440W into 2Ohms and 2x 2.880 in 4Ohms stereo bridge mode it is an extremely efficient solution for touring and installation sound reinforcement weighing in at a mere 8.6kg.
Consistent operation is ensured by the heavy duty construction with high quality components and comprehensive protection circuitry including soft start with turn-on muting, PMS™ power management, SSP™ (Safe operation Sentry Protection) and ICL™ Intelligent Clip Limiting to maintain signal integrity. Protection circuits against DC, thermal and power supply overload are implemented. A switchable subsonic filter and a 3-position gain switch offer variable amplifier adjustment.
The LDSP46K features a full 20Hz – 20kHz bandwidth with low THD and crosstalk, a damping factory higher than 500, excellent S/N ratio and 3 selectable gain/sensitivity levels.
Protection: Soft-start, Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short circuit, Open or mismatched loads, Overloaded power supply, ICL Clip Limiter, PMS, SSP
Controls: On/Off, Volume, Voltage Gain, Dual / Link switchable, Bridge / Stereo configuration switch
Very high power and channel density – • The four-channel FP
10000Q delivers a total of 10000 W (4 x 2500 W @ 2 ohms) in
only 2U
Four-channel fexibility – • Four channels in one cabinet increases
effciency, fexibility and value in powering monitor systems, line
arrays, and bi- or tri-amped systems. Adjacent channels bridgeable
for 2- or 3-channel operation
Lab.gruppen sound quality – • FP 10000Q amplifers maintain
the impeccable sonic performance standards set by the original fP
Series, with the same durability and even greater effciency
NomadLink • ® network ready – Monitoring and control of key
functions accessible via the intuitive DeviceControl software and
the robust, daisy-chained NomadLink® network
Patented Class TD amplifer topology – • Road-proven output
stage delivers Class B audio quality with Class D effciency
Regulated Switch Mode Power Supply (R.SMPS) – • Output
power remains constant even with signifcant drops in the mains
voltage
Effcient cooling system – • Unique, lightweight Intercooler® cop-
per cooling system dissipates more heat to allow extended peak
output
Adjustable parameters – • Selectable Gain, scalable Voltage Peak
Limiter (VPL), and bridge-mode operation allow custom confgura-
tion for any system or application
XLR input connectors •
Heavy-duty binding post or Speakon output connectors •
Comprehensive protection and warning – • Excessive output
current, DC, high temperature, very high frequency (VHF), short
circuit, open load, mains fuse protection, and soft start
Τελικός ενισχυτής 4x75W/8Ω. Ευαισθησία 1.4V -
Απόκριση συχνότητας (at 1W into 4/8 ohms) ±
0.5Db-Crosstalk (below rated power 20Hz to
1kHz) > 70dB S/N110dB-THD 55dB, typically
> 70dB. Διαστασεις: 1.75" x 19" x 14.25“.
Κατάλληλος για μόνιμες εγκαταστάσεις, 1U rack.
Βάρος 4,5kg.
• Eight and four channel models with 300W and 150W per channel • Minimal footprint and mass arround 200mm depth and 6 Kg • Optional Add-on card to interface with third party alarm systems with GPIO connections • FCM™ Faulty Channel Management system to avoid entire device shutdown • State-of-the-art layout for maximum performance and reliability • Highly oversized thermal dissipation design for maximum reliability • Superb distortion and noise figures • All channels bridgeable by pairs • Selectable gain in four channel groups (26, 32 and 38dB) • Subsonic filter per channel (35Hz user selectable) • Temperature and signal dependant, intelligent cooling system for minimal noise • Optimal heat extraction due to the air tunneled enclosure and insulator-less power device attachment to the heatsink • Direct connector-less output for maximum quality loudspeaker control • High grade engineering inside with the latest SMD technology • Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection • Critical electronic and mechanical parts selection • Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection • Detented and optionally tamper-proof volume potentiometers • Hi efficiency, two steps Class H Audio topology • Protection, Signal and Clip indicators per channel • Power On and Standby general indicators • Extremely compact, fully featured QuantaPulse Power supply • Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations • Factory preset worldwide mains voltage power supply • Laser cut four milimeters aluminium front panel • Rugged 2U steel chasis
OUTPUT POWER
T-604
T-1204
T-1208
T-2408
RMS, 1kHz, 1.0% THD+N
4 ohms
4x 160 W
4x 320 W
8x 150 W
8x 300 W
8 ohms
4x 115 W
4x 220 W
8x 100 W
8x 195 W
Bridge @ 8ohms
2x 320 W
2x 640 W
4x 300 W
4x 600 W
Pink Noise 12dB CF
4 ohms
4x 210 W
4x 415 W
8x 180 W
8x 370 W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >70dB
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™
• Eight and four channel models with 300W and 150W per channel • Minimal footprint and mass arround 200mm depth and 6 Kg • Optional Add-on card to interface with third party alarm systems with GPIO connections • FCM™ Faulty Channel Management system to avoid entire device shutdown • State-of-the-art layout for maximum performance and reliability • Highly oversized thermal dissipation design for maximum reliability • Superb distortion and noise figures • All channels bridgeable by pairs • Selectable gain in four channel groups (26, 32 and 38dB) • Subsonic filter per channel (35Hz user selectable) • Temperature and signal dependant, intelligent cooling system for minimal noise • Optimal heat extraction due to the air tunneled enclosure and insulator-less power devices attachment to the heatsink • Direct connector-less output for maximum quality loudspeaker control • High grade engineering inside with the latest SMD technology • Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection • Critical electronic and mechanical parts selection • Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection • Detented and optionally tamper-proof volume potentiometers • Hi efficiency, two steps Class H Audio topology • Protection, Signal and Clip indicators per channel • Power On and Standby general indicators • Extremely compact, fully featured QuantaPulse Power supply • Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations • Factory preset worldwide mains voltage power supply • Laser cut four milimeters aluminium front panel • Rugged 2U steel chasis
OUTPUT POWER
T-604
T-1204
T-1208
T-2408
RMS, 1kHz, 1.0% THD+N
4 ohms
4x 160 W
4x 320 W
8x 150 W
8x 300 W
8 ohms
4x 115 W
4x 220 W
8x 100 W
8x 195 W
Bridge @ 8ohms
2x 320 W
2x 640 W
4x 300 W
4x 600 W
Pink Noise 12dB CF
4 ohms
4x 210 W
4x 415 W
8x 180 W
8x 370 W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >70dB
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™
The DPA series amplifiers are digital power amplifiers designed to meet the specialized needs of sound contractors for Multi-Zone distributed speaker systems. They are designed in six different models of Class D power amplifiers, divided in three different architectures to meet the requirements for all kinds of applications.
They combine the best of all features in one single series of amplifiers, providing an outstanding sound quality with all the known advantages of Class D Amplifiers. Such as the excellent efficiency and very low heat dissipation. And due to the complete passively cooled entity only a minimal of maintenance is needed, while ensuring maximum reliability.
The small size of a single rack space make them very interesting for fixed rack mount as well as mobile applications.
The DPA74 is built as multi channel power amplifier with four individual controllable channels containing various specific features and advanced protection circuitry which protects against DC malfunctioning, short circuit, overheating and overload.
The signal input connections are accommodated with balanced XLR connectors. The operation mode can be selected between Stereo mode, Bridge mode and Parallel mode. The output connections are accommodated with Euro-Terminal blocks.
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.