Content |
Passive 4-channel DI BOX in a 19" housing. Each channel has a jack input with a parallel output for looping the signal through. An attenuation switch (-30dB) permits connection of a line or speaker signal at the user's choice. The specifications are identical with those of the PAN 01. All connections and switches are on the 1 U front panel; the XLR output is additionally present as a parallel socket on the rear panel. 19“/1 U housing, 90 mm deep.
Features: - Trafosymetric XLR Output
- Input Sensitivity Adjustable
- Input Impedance: 68,000 ohms
- Output Impedance: 600 ohms
- Transformer Ratio: 10 : 1
- Maximum Output: +6 dB
- Ground lift switch
- 19“/1 U Housing, 90 mm deep
|
The alphaton Direct Injection-Box SM-50 allows direct connection of electric guitars,
electric bass, and electronic music instruments with mixing desks of PA systems
and of recording studios.
The SM-50 reduces the amount of microphones used on stage, thus improving gain
before feedback.
Coloration of sound is avoided. Clean signal without interference from other instruments
eases the job of the recording engineer. The use of a strong aluminium die-cast box allows
trouble-free function for a number of years even under adverse conditions. Double grounding
(hum) can be eliminated by activating the built-in ground-lift switch. Isolation voltage between
input and output is 2500 volts, against ground 1500 volts (with ground-lift switch activated).
The box thus complies with toughest safety standards.
Technical Data
input impedance 20 kOhm
input impedance, instrument
input impedance, line-In
input impedance, speaker
output impedance 200 Ohm
frequency response 30 ... 20000 Hz, ± 1 dB
THD
isolation voltage tranformer pri/sec 2500 V
outpur to ground 1500 V
inputs 1/4" phone jacks, unbalanced
outputs XLR, balanced, microphone level.
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 230 g
dimensions113 x 71 x 37 mm
|
The Stewart ADB-1 is a single channel active direct box that allows an unbalanced source to directly feed a balanced input. Musical instruments, tape recorders, VCRs and sound projectors can be run "direct" to the mixing console, avoiding unnecessary degradation of sound quality. The ADB-1 operates on either phantom power or a 9-volt battery.
FEATURES: Flat response Low distortion Low noise Wide dynamic range No transformer RF protection on input and output Switchable ground isolation Flush mounted slide switches |
Behringer DI-400P High-Performance Passive Direct Injection Box Introducing the Ultra-Compact DI-Boxes from BEHRINGER There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal. The DI400P lets you connect instruments or amplifier outputs. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies. This is the sort of medicine that?ll cure headaches in your studio or on stage.
| Little brother of the LH-055 DI Box. Sturdy housing, solid workmanship at an unbeatable price.
1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal (e.g. to a guitar amplifier) 1 low-impedance output (XLR) Black housing
Passive 1-channel DI box, black
- 1 high-impedance signal input, 6.3 mm jack
- 1 low-impedance XLR output
- 6.35 mm jack input, and output
- Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
- Switchable input attenuation: 0 dB, -20 dB, -40 dB
- Rugged black metal housing
Package contents
- 1 x device, 1 x user manual
Frequency range: |
15 - 30000 Hz |
S/N ratio: |
>95 dB |
Impedance: |
Input: 50 kOhm
Output: 600 Ohm |
Input attenuation: |
0 dB, -20 dB, -40 dB; switchable |
Control elements: |
Groundlift selector |
Connections: |
Input: 1 x 6.3 mm plug (unbal.)
Link: 1 x 6.3 mm plug (unbal.)
Output: line via 1 x 3-pin XLR |
Dimensions: |
Width: 12,7 cm
Depth: 7,4 cm
Height: 4,5 cm |
Weight: |
440 g |
| Behringer DI-600P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal. The DI600P lets you connect instruments or amplifier outputs of up to 3,000 Watts. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies. This is the sort of medicine that?ll cure headaches in your studio or on stage.
It often happens that you want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. The direct connection between audio equipment can quickly turn out to be a real challenge: technical problems crop up that can affect the signal.
Hook Your Guitar or Amp Up to the PA
Be ready for your next gig with the Behringer Ultra-DI DI600P direct box. Designed to send instrument or amplifier signals to the main mixing board, the DI600P is a high-performance passive DI is a useful tool in any gig rig or studio. Dual 1/4" TS jacks are wired in parallel let you plug your instrument into one and use the other as an output to your amp. The balanced XLR mic-level output feeds your mixer a clean and super-flat signal that is true to the source. Sweetwater knows that grounding issues and hum can be a problem at live gigs. The DI600P sports a ground lift switch to kill unwanted ground loops and hum. It also has a filter switch for optimal guitar tone and an instrument/amp switch with a 30dB input level drop. The Behringer Ultra-DI DI600P direct box is an extremely useful tool for any stage rig!
Behringer Ultra-DI DI600P Direct Box Features:
- Compact, high-performance passive direct box
- Jack input 1/4" TS in and parallel out
- Gold-plated XLR output / impedance balanced
- Super-flat frequency output for uncolored sound
- Switchable filter that optimizes the DI for guitars
- Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
- Instruments or amplifier outputs with up to 3,000 watts can be connected directly
- Offers impedance and signal matching of instruments to mixers
- Perfect for stage and studio use
- Ground lift switch eliminates typical ground loop problems
- Rugged metal case can take the rigors of the road
Get your signal to the board with Behringer's Ultra-DI DI600P direct box!
Tech Specs
- Type: Passive DI Box
- Channels: 1
- Ground Lift: Yes
- Inputs: 1 x 1/4"
- Outputs: 1 x 1/4“, 1 x XLR
- Height: 1.4"
- Width: 3.75"
- Depth: 5"
- Weight: 0.66 lbs.
- Manufacturer Part Number: DI600P
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.