Content |
The VM-3240E is a multifunctional amplifier that can be mounted in an EIA-Standard equipment rack (3-unit size). The unit comes with the speaker output section which has an internal attenuator and 6-output selector. In addition, the unit features the surveillance function which automatically checks the system for failures.
Power Source | 230 V AC, 50/60 Hz | Power Consumption | 600 W (with rated output signal), 260 W (according to EN60065) | Rated Output | 240 W | Frequency Response | 50 Hz - 20 kHz, ±3 dB (at 1/3 rated output) | Distortion | 0.7 % or less (at rated output, 1 kHz) | S/N Ratio | 85 dB or more | Input | External amplifier input: 100 V line, removable terminal block (14 pins) | Output | Speaker output 1 - 2: Max. (240 W) per output
Speaker output 3 - 6: Max. (120 W) per output
Speaker output 1 - 6: Total within 240 W, removable terminal block (14 pins)
Allowable minimum load: 500 Ω (20 W) at 100 V line for speaker line failure detection
Direct output: Direct output from internal or external amplifier,
removable terminal block (16 pins) | VM Link | Input: Connecting the VM-3240VA or VM-3360VA, RJ45 female connector
Output: Connecting the VM-3240E or VM-3360E, RJ45 female connector
Maximum distance: 800 m (874.89 yd)
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | EXT PA Link | Connecting the VP-2241, RJ45 female connector
Maximum distance: 5 m (16.4 ft)
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | General Control | Input 1 - 8: No-Voltage make contact input, open voltage: 24 V DC,
short-circuit current: 2 mA or less, removable terminal block (14 pins)
Output 1 - 8: Isolated open collector output, withstand voltage: 30 V DC,
operating current: 10 mA or less, removable terminal block (14 pins) | Emergency Control | Input 1 - 5: No-Voltage make contact input, open voltage: 24 V DC,
short-circuit current: 2 mA or less, RJ45 female connector
Input 6: Isolated voltage input, Inactive: -24 V ±20 %, Active: +24 V ±20 %,
RJ45 female connector
Status out: Relay contact output, withstand voltage: 40 V DC,
operating current: 2 - 300 mA, RJ45 female connector | ATT Control | Relay contact 1-6, 125 V AC or 30 V DC, total under 5 A,
removable terminal block (16 pins) | Power Input/Output | Power in: Connecting the VX-2000DS only (operating range: 20 - 40 V DC)
PS out: 28 V DC/18 A
M4 screw terminal, distance between barriers: 11 mm (0.43“) | DC24V Output | 24 V DC, Maximum feeding current 0.3 A | Ds Link | Connecting the VX-2000DS, RJ45 female connector
Maximum distance: 5 m (16.4 ft)
Link cable: Category 5 Shielded Twisted-Pair straight cable (CAT5-STP) | Operating Temperature | -5 ℃ to +45 ℃ (23 ゜F to 113 ゜F) | Operating Humidity | 5 % to 95 %RH (no condensation) | Finish | Panel: Aluminum, hairline, black
Case: Surface-treated steel plate, black, paint | Dimensions | 482 (W) × 132.6 (H) × 407 (D) mm (18.98" × 5.22" × 16.02“) | Weight | 16.5 kg (36.38 lb) | Accessory | Power cable (2 m (6.56 ft)) …1, Link cable (3 m (9.84 ft)) …2,
Plastic foot …4, Plastic foot mounting screw …4,
Removable terminal plug (14 pins) …3, Removable terminal plug (16 pins) …1 |
|
XV Series - Intelligent Power Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 1600: 2x 800 W / 100 V Class: AB Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans(temp. reg. variable speed) Weight: 39 kg Dimensions: 3 RU / 483 x 88 x 382 mm(19" x 3.5" x 15 |
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 1000: 2x500 W/100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 33 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Ολοκληρωμένος ενισχυτής PA 120 WRMS, με μετασχηματιστή εξόδου 100V, με 3 mic& 2 AUX input, phantom power, high/low ρυθμιστικό EQ & priority mute στο mic 1, βάρος 10.8 kg. Εφαρμογές: σε εγκαταστάσεις 100V, μικρά καφέ, καταστήματα, εργοστάσια, κ.α.
Specification |
| Power Source | 220 - 240V AC or 24V DC | Rated Output | 120W | Power Consumption | 124W (EN60065), 260W(AC operation at rated output, 8A (DC operation at rated output) | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | Distortion | Under 1% at 1kHz,1/3 rated power | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:83W (100V)
LOW IMPEDANCE: 4Ω (22V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | Phnatom Powe | DC + 21V (MIC 1) | S/N Ratio | Over 60dB | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | Indicator | Power signal, peak | Finish | Panel: ABS resin, black/Case: Steel plate, black | Dimensions | 420 (W) x 100.9 (H) x 360.3 (D) mm | Weight | 10kg |
|
Τελικός ενισχυτής 4Χ250W/4Ω, δυνατότητα bridge λειτουργίας (500W /8Ω), είσοδοι balanced με phoenix connectors, έξοδοι barrier strip, ύψος 1U, δυνατότητα για 4 διαφορετικές εισόδους. Με μετασχηματιστή γραμμής 100V για σταθερού voltage εγκαταστάσεις. 6,8Kg.
- 4x 250W (4 ohms) / 170W (8 ohms)2x 500W bridged mode (8 ohms)
- Limiter
- Class D design – 85% efficient!
- 30% lower power consumption than conventional amplifiers
- Compact, single rack-space design
- Stack up to 5 units without open spaces between units
- Lightweight (14.6 lbs.)
- Independent power supply for each channel
- Low heat dissipation
- Recessed stepped attenuators
- Comprehensive protection circuitry
- Removable dust filters for easy maintenance
- Optional 250W isolation transformer, model MT-250H (DA-250FH only)
|
Specifications Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| Sensitivity (at 8 ohm rated output) |
1.4V
| Maximum Input Signal |
+22 dBu typical
| Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| Ventilation |
Flow-through ventilation from front to back
| Cooling |
Heat sinks and proportional-speed fan
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.