ALPHATON SM-50 PASSIVE D.I-BOX WITH GROUNDLIFT

The alphaton Direct Injection-Box SM-50 allows direct connection of electric guitars,
electric bass, and electronic music instruments with mixing desks of PA systems
and of recording studios.
The SM-50 reduces the amount of microphones used on stage, thus improving gain
before feedback.
Coloration of sound is avoided. Clean signal without interference from other instruments
eases the job of the recording engineer. The use of a strong aluminium die-cast box allows
trouble-free function for a number of years even under adverse conditions. Double grounding
(hum) can be eliminated by activating the built-in ground-lift switch. Isolation voltage between
input and output is 2500 volts, against ground 1500 volts (with ground-lift switch activated).
The box thus complies with toughest safety standards.

Technical Data

input impedance 20 kOhm
input impedance, instrument input impedance, line-In input impedance, speaker output impedance 200 Ohm
frequency response 30 ... 20000 Hz, ± 1 dB
THD isolation voltage tranformer pri/sec 2500 V
                        outpur to ground 1500 V
inputs 1/4" phone jacks, unbalanced
outputs XLR, balanced, microphone level.
           pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 230 g
dimensions113 x 71 x 37 mm
 

At dbx, when we do something, we do it right. So when we decided to create our new direct injection boxes, we didnʼt settle for the same old tired approach to direct box design. With our dbx name on the line, how could we? One look at our new dB10 Passive and dB12 Active direct boxes will tell you that these are clearly different. With their bullet-proof construction, and extraordinary audio performance to rival their looks, finally thereʼs a direct box worthy of the dbx name.

Utilizing custom dbx mu-metal-shielded audio transformers, high-quality Neutrik® connectors, and low-noise circuitry preserves the sonic integrity and true characteristics of the signal source. Both boxes include a pad switch that accomodates instrument, line and even speaker level signals. Take even more control of your sound by utilizing the polarity invert switch to set the phase relationship between the direct and mic'd sound.

As a professional, you donʼt have time for interference, so weʼve included a ground lift switch to solve potential hum and buzz problems due to ground loops. And between the combined shielding of the cast metal chassis and the custom-wound transformer, you can be doubly assured of a clean signal free from interference. All of this sits atop a solid, stable footprint, that will keep the box from being dragged around the stage, and the unique contoured underside allows secure stacking of multiple units.

So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx dB10 dB12 is for you.

Input: 1 instrument/line/speaker level

Connector: 1/4" jack

Type: Unbalanced, RF filtered

Impedance: 150k Ohm typical

Max Input Level: +20dBu (0dB pad)
+40dBu (20dB pad)
+60dBu (40dB pad)

Thru Output: 1 parallel connection from input jack

Connector: 1/4" jack

Type: Unbalanced, RF filtered

Main Output: 1 line level

Connector: XLR male jack

Type: Balanced

Impedance: 150 Ohm typical

Max Output Level: 0dBu

Transformer: Custom dbx mu-metal-shielded

Frequency Response: 20Hz to 20kHz, +/-2.5dB

Noise:

THD:

Dimensions: 5.82" L X 5.44" W X 2.20" H (148 x 138 x 56mm)

Weight: 1.4 lbs / 0.65 kg

Note: Specifications subject to change without notice.

• Compact, high-performance passive direct box
• Jack input 1/4" TS in and parallel out
• Gold-plated XLR output / impedance balanced
• Super-flat frequency output for uncolored sound
• Switchable filter that optimizes the DI for guitars
• Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
• Instruments or amplifier outputs with up to 3,000 watts can be connected directly
• Offers impedance and signal matching of instruments to mixers
• Perfect for stage and studio use
• Ground lift switch eliminates typical ground loop problems
• Rugged metal case can take the rigors of the road

• Type: Passive DI Box
• Channels: 1
• Ground Lift: Yes
• Inputs: 1 x 1/4"
• Outputs: 1 x 1/4“, 1 x XLR
• Height: 1.4"
• Width: 3.75"
• Depth: 5"
• Weight: 0.66 lbs.
• Manufacturer Part Number: DI600P

Active DI-Box SM-60

The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.

Technical Data

input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
       < 0,7 % bei 40 Hz
powering  9-V battery (IEC 6LF22) or
                 phantom power 24 ... 48 V.
inputs  two 1/4" phone jacks , unbalanced
          (one being used as output to instruments amp)
outputs  XLR, balanced
             pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm

Phantom or battery powered in a rugged steel chassis, with separate Speaker Level input connector
 
The ARX DI-PLUS represents another major step forward in active direct boxes. Packaged in
a single channel stand-alone format, the DI-PLUS represents a fresh look at active D.I. concepts.
Precision engineered
Ultra quiet, ultra clean circuitry delivers maximum headroom whatever the signal. Premium grade
components, plus an all-steel chassis gives excellent hum and noise specifications and superb
audio quality in a tough, roadworthy package.
Level control
The DI-PLUS features a Normal gain high impedance unbalanced input on the front panel, running to
a balanced XLR output on the rear. There is also a separate -40dB Speaker Level input for signal coming
from the External (auxiliary) speaker output of an amplifier. A a global Pad switch drops both the normal
input and the speaker input by a further 20dB, making it suitable for all applications, from the softest
keyboard to the hottest broadcast levels.
 
Battery compartment
The revolutionary simple 'clamshell' action of the DI-PLUS battery compartment makes battery changing
extremely easy, even on the darkest stages.
A 9v alkaline battery snaps into a PCB mounted battery holder for fast, secure location. No fragile battery
clip leads to break, no tools required, no screws to lose. Production crew heaven!
 
Automatic Phantom switching
The DI-PLUS will automatically switch itself to the console's own Phantom Power, if available, and an LED
will indicate this mode. Turn the Phantom Power off and it will instantly revert back to battery mode.
Rugged all-steel case
A lot of direct boxes are fitted into brittle cast alloy cases. Not this one! The tough all-steel inner and outer
chassis of the DI-PLUS provide excellent RF/EMF shielding while making it a sturdy, heavy duty unit that is
hard to dislodge, and hard to leave behind.
 
Rear panel showing XLR connector, ground lift switch, and captive screw for opening up the unit
for battery changing
 
Whether you're a Studio or Live Sound engineer, installation contractor, or broadcast engineer, you want all
the dynamics and clarity of the original sound source transferred to the mixing console. The ARX DI-PLUS
provides a rugged, no-compromise solution to all direct injection and signal balancing requirements.
 
T E C H N I C A L  S P E C I F I C A T I O N S:
Max Input Level
+13 dB Phantom powered
+6 dB Battery powered
Input Impedance 1 Meg Ohm
Max Output Level
+17 dB 10K Ohm load Phantom powered
+12 dB 10K Ohm load Battery powered
+11 dB 600 Ohm load Phantom powered
+12 dB 600 Ohm load Battery powered
Output Impedance 680 Ohms Balanced
Output Signal to Noise
-100 dB unweighted
-104 dB A weighted
Dynamic Range
117 dB 10K Ohm load Phantom powered
112 dB 10K Ohm load Battery powered
111 dB 600 Ohm load Phantom powered
107.5 dB 600 Ohm load Battery powered
Distortion
100 Hz .0027%, 1KHz .0028%, 10KHz .0037%
Frequency Response 20Hz to 20KHz, ± 0.2 dB
Gain through Unit: 6dB (Normal input, Pad switch out)
Pad Switch: -20 dB attenuation
Speaker Input
-40 dB attenuation, equivalent to 100:1 decrease in input level
-60 dB attenuation available with Pad switch
Input Connectors
Insulated jacks (!!!Note that the Input connector switches the unit on
when a plug is inserted. Remove plug when storing to avoid battery drain!!!)
Output Connector
3 pin XLR. Wired Pin 1 Ground, Pin 2 + Hot, Pin 3 - Cold.
With Audio Ground (Pin 1) lift switch
Construction
All-steel chassis, fibreglass PCB
Battery Access
Twist connector opens chassis, snap-in battery holder inside.
No tools required