AMERICAN AUDIO XEQ-152B EQUALIZER 2×15 BAND GRAPHIC EQUALIZER

* 2 channel 15 2/3 octave band graphic equalizer
* 25Hz - 16kHz frequency control * Constant Q circuitry
(3% frequency accuracy) * Selectable 6dB or 12dB control
* Variable level control * By-pass switch * Overload threshold LED (5dB below clipping) * Ground lift switch * XLR & 1/4" TRS balanced Inputs/Outputs * Power: Selectable 120V/220V voltage
* Dimensions: 1.75" H x 19" W x x 8.5" D / 44.5mm x 483mm x 216mm - 1 space r.m. * Weight: 4.5 lbs. / 2.5kg

XEQ-152 Specifactions:
* Input type: Active balanced / Unbalanced * Output Impedance:

The S com 4 is a compact and versatile single-rack space device that provides
four channels of high quality dynamics processing with an Expander/Gate and
Compressor/Limiter on each channel.
The four channels operate independently or in stereo pairs. Its multi-segment LED
metering displays input/output level as well as gain reduction. The Expander/Gate
section features a continuously variable Threshold control as well as a switch for
fast or slow release times.
The Compressor/Limiter section includes variable Threshold, Ratio and Output levels.
S com 4's Enhancer switch restores high frequencies that are sometimes diminished
by heavy compression. This wide-ranging combination of features makes the S com
4 an efficient and versatile audio tool for a wide variety of applications. Its clean and
quiet audio characteristics make it ideal where high sonic integrity is imperative. 
 
FEATURES:

4 Channel Compressor/Limiter, Expander/Gate with Enhancer
Linkable in two Stereo pairs
Expander/Gate with variable Trigger control and switchable Fast/Slow Release
5 Segment LED meters for Input/Output levels and Gain Reduction on each channel
Advanced circuit design utilizing Low Noise Operational
Amplifiers and High Quality VCA's
Servo Balanced Inputs and Outputs on XLR and 1/4" connectors
SKD (Smart Knee Detector) circuit automatically switches from soft to hard knee
based on the level of Input signal applied
Individual Threshold and Ratio controls on each channel
Three-year extended warranty 

The latest addition to the 10 Series product line, the dbx® 1074 QuadGate™, is the perfect companion to the 1066 and 1046. The 1074 offers 4 channels of gating with threshold, depth and release controls on each channel. The 1074, like the rest of the products in dbx 10 Series, is based on the legendary dbx V2 VCA and offers XLR inputs and outputs, and 1/4” side-chain input. In addition to an external key input per channel, the 1074 also has an internal filter that can be independently activated and controlled on a channel-per-channel basis. This filter allows the 1074 to not only clean up tracks, but gives you frequency selective control on each gate, to open exactly when you want it to. These features combined, make the 1074 an absolute must for those who require quad gating on applications including: Gating dry and percussive sounds such as snare drum and kick drum,gating sounds that have longer decay times such as cymbals and Pianos, gating hum or buzz from live instruments or recorded tracks or eliminating Headphone leakage into microphones. Gating instrument microphones to eliminate amplifier bleed. 

From the company that has been redefining the standard of signal processing for more than 30 years, dbx® Professional Products comes a bulletproof product that caters to the scrutinizing needs of those who require the precision noise gating capabilities. Once again, the engineering staff at dbx® Professional Products have taken technology that has been over three decades in the making and have created a product that is flexible, versatile and rock solid in construction design. The 1074ʼs independent channel design with key filtering capabilities make it the perfect tool for countless applications.

• Four independent channels of gating
• Independent key filtering
• Independent Threshold and Release controls
• Differentially balanced gold-plated XLR and 1/4" inputs and outputs
• True RMS level detection
• Stereo Coupling mode
• Switchable +4dBu or -10dBv operation per channel
  
  

  Input Connectors	XLR (Pin 2 and tip hot)
  Input Type	Electronically balanced/unbalanced, RF filtered
  Input Impedance	Balanced > 50 kOhm, unbalanced >25 kOhm
  Max Input	> +22 dBu balanced or unbalanced
  CMRR	40dB: Typically >55 dB at 1 kHz
  Key Input	Electronically balanced/unbalanced, RF fitered Balanced 50kOhm, unbalanced > 25 kOhm
  Output Connectors	XLR (Pin 2 hot)
  Output Type	Servo-balanced/unbalanced, RF filtered
  Output Impedance	Balanced 60 Ohm, unbalanced 30 Ohm
  Max Output	> +22 dBm balanced, > +20 dBm unbalanced
  Bandwidth	20 Hz to 20 kHz, +0/-0.5 dB
  Frequency Response	0.35 Hz to 200 kHz, +0/-3 dB
  Noise
  Dynamic Range	> 115 dB, unweighted
  THD+Noise	0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain),
  Interchannel Crosstalk
  Stereo Coupling	True RMS Power Summing
  Operating Voltage	100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz
  Power Consumption	30 Watts
  Fuse	100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T
  Power Connector	IEC receptacle
  Unit Weight	6.9 lbs.
  Shipping Weight	9.3 lbs.

  
  

The class-A circuit used in the EQ-73 is similar to the eq section in the classical 1073 module, without the high pass filter. Additional frequencies have been added and the mid frequency band uses two inductors, the higher value of the second one is used for the two lowest frequencies, 160 Hz and 240 Hz, to achieve a suitable response.

The sound character is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

The EQ-73 has stepped frequency controls that offers a wide selection of frequencies from 20 Hz to 24 kHz.

The Low and High frequency bands are shelving and the mid frequency band is of the bell type.

The control range is +/-15 dB for the two lower bands and +/- 18dB for the high frequency band.

There are separate bypass switches for all three bands.

The EQ-73 is made to be used together with one of our PRE-73 models that has an Insert jack. It can also be used with many other units that has a low level insert jack.

Combining a PRE-73 and an EQ-73, and using a UNITE rack kit to mount them together, one will get a 19-inch 1073-style unit at a low cost and with a great sound!

FEATURES

- Vintage Style electronics. No intergrated circuits in the signal path

- 3-band with a dual inductor based mid frequency band

- Stepped frequency selection

- A wide selection of frequencies from 20 Hz to 24 kHz

- Control range up to +/- 18 dB

- Separate Bypass switches for each band

- Tantalum capacitors in the signal path

- Made to be used together with one of our PRE-73 models with an Insert jack or any other unit with a low level Insert jack

- TRS jack for in-and output connection, the nominal working level is around 18 dBu

- Selectable ground lift switch

- External power supply to avoid interaction with the audio circuits

- Great sound that suits most sound sources and genres

- A solid build quality that will last many years of normal use

• Professional 15-band stereo graphic equalizer for live and studio applications
• Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
• Ultra-low noise 4580 operational amplifiers for highest signal integrity
• Dedicated mono subwoofer output with adjustable crossover frequency
• Additional low-cut filter removes unwanted frequencies, e.g. floor rumble

• Highly accurate 4-segment LED output metering and input gain controls for easy level setting
• Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
• “Planet Earth" switching power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
• 3-Year Warranty Program*
• Designed and engineered in Germany