| Content |
The new AT2010 is designed to bring the studio-quality articulation and intelligibility of Audio-Technica's renowned 20 Series to the stage, for crystal-clear vocal performances. Featuring the same 16 mm low-mass diaphragm found in the critically acclaimed AT2020 side-address studio condenser, the AT2010 excels wherever articulate vocals are needed: in houses of worship, for solo performances, jazz vocalists, singer/songwriters, and more.
- Extended frequency response and superior transient response for smooth, natural sonic characteristics
- High SPL-handling and wide dynamic range provide unmatched versatility
- Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source
- Multi-stage grille design offers excellent protection against plosives and sibilance without compromising high-frequency clarity
- Corrosion-resistant contacts from gold-plated XLRM-type connector
- Rugged, all-metal and construction for years of trouble-free service
- Quiet-Flex stand clamp provides silent, flexible microphone positioning
- Element: Fixed-charge back plate permanently polarized condenser
- Polar Pattern: Cardioid
- Frequency Response: 40-20,000 Hz
- Open Circuit Sensitivity: 48 dB (3.9 mV) re 1V at 1 Pa
- Impedance: 100 ohms
- Maximum Input Sound Level: 136 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 113 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 71 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 48V DC, 2 mA typical
- Weight: 233 g (8.2 oz)
- Dimensions: 179.1 mm (7.05“) long, 50.8 mm (2.00“) maximum body diameter
- Output Connector: Integral 3-pin XLRM-type
- Accessories: AT8470 Quiet-Flex stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; soft protective pouch
| NT3 - Versatile & Dependable
Stylish and modern, the NT3 is a studio and location workhorse. With both
48V phantom and internal 9V battery operation, this R?DE is at home anywhere.
Intended for studio, stage and location work, this versatile handheld or stand
mounted microphone incorporates a true externally polarized condenser (hyper-
cardioid polar response) transducer with an internal capsule shock mounting
system, and an ultra-low noise electronic circuit that has a high immunity to R.F.
interference. Incorporating a rugged welded and heat-treated mesh head and all
metal body. The NT3 is supplied in a zip pouch with a windshield, stand mount
and thread adaptor.
SPECIFICATIONS:
Acoustic principle: Externally polarised 19mm (3/4“) condenser
Directional pattern: Hypercardioid
Frequency range: 20Hz-20 kHz
Output impedance: 200?
Signal noise ratio din iec 651: > 77dB (per IEC268-15)
Equvalent noise: 123dB (per IEC268-15)
Power supply voltage: P48, P24, P12 phantom 9V battery
Weight without battery: 371g
Weight with battery: 680g |
The e 865 is a fully professional super-cardioid vocal microphone utilising the
very best in condenser microphone technology to achieve new standards of
quality and sound. The microphone capsule insorporates special blast/pop
protiction plate to shield the diaphragm from excessive sound pressure levels.
Features
Rugged metal body
Extended dynamic response with pronounced presence and vocal 'punch'
Excellent feedback rejection
Very good rejection of handling noise
Very high sound pressure handling capability
Delivery Includes
1 e 865
1 microphone clip
1 pouch
Technical Data
Pick-up pattern super cardioid
Sensitivity in free field, no load (1kHz) 3 mV/Pa
Max. Sound pressure level (aktiv) 150 dB
Nominal impedance 200 Ohm
Min. terminating impedance 1000 Ohm
Dimensions d 47 x 193 mm
Weight w/o cable 311 g
Frequency response (microphone) 40.....20000 Hz
Phantom powering 12 - 48 V
|
Cardioid Condenser with 10dB Attenuator and 3 Position Low-Cut Filter
One of the world's great studio microphones, the SM81 provides precise, detailed sound reproduction, is excellent for studio recording, and is rugged enough for live sound reinforcement.
- A standard for acoustic instruments, including guitar and cymbals
- Selectable, low-frequency response -- either flat, 6dB/octave roll-off, or 18 dB/octave roll-off
- Built-in, switchable 10 dB attenuator for use in high SPL situations
- Phantom power only
- Windscreen included
- Low noise and high output clipping
- Cardioid condenser
- Frequency response: 20 to 20,000 Hz
|
C 568 B
Compact, short shotgun microphone
Integrated, switchable bass cut filter minimizes mechanical noise
Operates on phantom power
High directivity and wide frequency response in a relatively short shotgun make this
microphone a perfect tool for theater, sound reinforcement, and film/TV applications.
Due to its compact and lightweight design, the C 568 B is ideal for camera mount
applications. Below 500 Hz it functions as a hypercardioid microphone; above 500 Hz
the acoustic interference tube introduces increasing directivity. A switchable 12 dB/
octave 120 Hz bass cut filter effectively suppresses rumble and wind noise. The rugged,
all-metal body contains the built-in preamp. Phantom powering (9?52 V) required; foam
windscreen and stand adapter included.
SPECIFICATIONS:
Polar pattern hypercardioid/directional
Frequency range 20 to 20,000 Hz
Sensitivity 11 mV/Pa (-39 dBV)
Max. SPL 128 dB
Equivalent noise level (CCIR 468-3) 29 dB
Equivalent noise level 18 dB-A
Signal/noise ratio 76 dB
Bass filter 12 dB/octave at 120 Hz
Impedance 600 ohms
Recommended load impedance >2000 ohms
Supply voltage 9 to 52 V phantom power to DIN 45596
Current consumption |
The ME 65 is a super-cardioid microphone head designed for use with the K6 and K6P powering modules. It is especially suited to vocal and speech applications. Matt black, anodised, scratch-resistant finish.
- Pick-up pattern : super-cardioid
- Sensitivity in free field, no load (1kHz) : 10 mV/Pa +- 2,5 dB
- Nominal impedance : 200 Ohm (K6)
- Min. terminating impedance : 1000 Ohm (K6)
- Equivalent noise level : 20 dB
- Dimensions : d 44 x 131 mm
-
Weight :
|
Reviews
There are no reviews yet.