| Content |
The white-finished version of the U851R, the phantom-powered U851RW features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. Offering outstanding speech intelligibility and transparent sound quality for surface-mount applications, the U851RW accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. With a heavy die-cast case and silicon foam bottom pads to minimize coupling of surface vibration to the microphone, the U851RW is equipped with self-contained electronics, eliminating the need for an external power module.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Self-contained electronics eliminate need for external power module
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Available in two colors: black (U851R) and white (U851RW)
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 108 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 4 mA typical
- Switch: Flat, roll-off
- Weight: 9.2 oz (262 g)
- Dimensions: 4.25" (108.0 mm) long, 3.31" (84.0 mm) maximum width, 0.91" (23.0 mm) height
- Output Connector: TB3M-type
- Cable: 25.0' (7.6 m) long, 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors
|
Type of Transmitter UHF Frequency Agile
Input Connector Internal fitting for interchangeable capsules
Type of Microphone Electret Condenser Boundary Microphone
Polar Pattern Cardioid (Supplied)
Interchangeable Mic Heads Yes - R183B Omnidirectional, R184B Supercardioid and R185B Cardioid cartridges available
Frequency Response 50Hz to 17kHz
Battery Type/Approx. Life 9 Volt Alkaline - 7 hours based on alkaline battery
# Of Channels Over 100 channels between 692-862MHz, depending on locale
Mute Switch Programmable Touch-Sensitive Switch
Level Control Gain Adjustment Range: -6 to 34dBs
Antenna Type Internal
Display Microphone Status & Battery Life LEDs
Dimensions 3.625 x 1.8 x 5.17 (92 x 46 x 131mm) (WxHxD)
|
Boundary-layer Microphone
The LD Systems BM1 is an electret condenser microphone with a hemispherical directional characteristic.
For micing upright and grand pianos on stage or in the studio. Additional applications in the area of conference technology, transmission of roundtable discussions and theatrical performances.
Product type
Microphones
Type
Installations
Frequency response
50 - 20000 Hz
Directivity
half ball
Nominal impedance
250 Ohm(s)
Max. SPL (1% THD @ 1kHz)
135 dB
Phantom power requierements
48 V
Microphone input
XLR (3-pin)
Width
27 mm
Height
74.5 mm
Diameter
93.5 mm
Accessories (included)
cables (Mini-XLR / XLR, 6 m)
Weight
0,345 kg
|
A wide range condenser microphone with a cardioid polar pattern, the ultra-smart U891RCx is equipped with local or remote switching options. For flexible control in conference and boardroom installations, the unit's external contact closure ability allows a user to trigger an external device - a camera, for instance - from a switch on the microphone. Another ease-of-use feature: the microphone's electronic on-off switch can be set to three operating modes: touch-on/touch-off, press to talk, and press to mute. The mic is also equipped an 80 Hz low-cut UniSteep® filter to reduce pickup of low-frequency ambient noise. Its red LED status indicator can be controlled remotely. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; a unique rotating PivotPoint® connector changes the cable exit point - no tools required. It requires 11 to 52V DC phantom power, which operates the microphone and switch circuitry.
- Designed for surface-mount applications such as high-quality sound reinforcement, conferencing, distance learning and other demanding sound pickup situations
- Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/touch-off," "touch-to-talk" and "touch-to-mute“
- External contact closure capability permits control of remote devices from microphone switch
- External LED control allows for accurate depiction of the live status of the microphone
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 104 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 11-52V DC, 4 mA typical
- Weight: 266g
- Dimensions: 108.0mm long, 84.0mm maximum width, 23.0mm height
- Output Connector: TB5M-type
- Cable: 7.6m long, 3.2mm diameter, 5-conductor shielded cable (2 conductors under shield; 3 control wires outside shield); TA5F-type connector at microphone end, output end stripped and tinned for connection to electronic device
| The PRO42\'s low-profile design assures inconspicuous appearance for surface-mount use in boardroom, school, government, house of worship and other installed applications. Designed for sound reinforcement, broadcasting and recording applications, the PRO42 brings crisp, intelligible audio reproduction to the podium, stage, conference table and beyond. With a wide-range condenser element and low-mass diaphragm for superior performance, the microphone is equipped with self-contained electronics, eliminating the need for external power modules.
Very low-profile design for minimum visibility
Wide-range condenser element with low-mass diaphragm for superior performance
Uniform polar pattern for maximum rejection of unwanted sounds
Rugged design and construction
25\' (7.6 m) cable permanently attached between microphone and XLRM-type connector
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
Frequency Response: 70-14,000 Hz
Open Circuit Sensitivity: -38 dB (12.5 mV) re 1V at 1 Pa
Impedance: 100 ohms
Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: 105 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 65 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 9-52V DC, 2 mA typical
Weight: 1.2 oz (35 g)
Dimensions: 1.44" (36.6 mm) maximum width, 2.14" (54.3 mm) maximum length, 0.61" (15.5 mm) height
Output Connector: 3-pin XLRM-type on cable
Cable: 25\' (7.6 m) long, permanently attached |
The new Engineered Sound.
This low-profile omnidirectional condenser boundary microphone is designed for clear, highly intelligible sound reinforcement, professional recording and teleconferencing in table-, ceiling-, or panel-mount applications. The microphone is equipped with a self-contained power module with an XLRM-type output connector, eliminating the need for an external power module. The microphone offers unsurpassed immunity from radio frequency interference thanks to Audio-Technica's UniGuard® innovations. Protected by a rugged all-metal case with a two-layer steel mesh grille, the microphone has a 360º pickup angle, and is available in two colors: black (ES945) and white (ES945W).
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording and teleconferencing
- Low-profile element provides uniform omnidirectional polar pattern with 360º acceptance angle
- Mounts unobtrusively in table-tops, ceilings and wall panels
- Self-contained power module with XLRM-type output connector
- Rugged all-metal case with a two-layer steel mesh grille
- Isolators provide mechanical dampening of mounting-surface vibration
- Requires 11V to 52V DC phantom power
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Available in two colors: black (ES945) and white (ES945W)
- RoHS compliant-free from all substances specified in the EU directive on hazardous substances
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Omnidirectional
- Frequency Response: 40-18,000 Hz
- Open Circuit Sensitivity: -42 dB (7.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 142 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 112 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 64 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Weight: 63 g (2.2 oz)
- Dimensions: 69.0 mm (2.72“) long, 28.0 mm (1.10“) diameter
- Output Connector: Integral 3-pin XLRM-type
|
Reviews
There are no reviews yet.