| Content |
Behringer B-5 Sputtered Diaphragm Studio Condenser Microphone
The B-5 is a professional gold-sputtered diaphragm condenser microphone featuring two interchangeable capsules for different pickup patterns (cardioid and omnidirectional). It is perfect for acoustic instruments, vocals and overhead miking. Its ultra low-noise transformerless FET input eliminates low frequency distortion. The -10 dB attenuator can be used with high volume signal sources, while the low-cut filter eliminates floor rumble. The microphone is delivered in a rugged hard case with stand adapter and windscreen.
|
|
|
|
|
|
|
Professional true condenser microphone for studio and live applications
|
|
|
2 interchangeable capsules with cardioid and omnidirectional pickup patterns
|
|
|
Low-mass gold sputtered diaphragm for ultimate sound reproduction
|
|
|
Perfect for acoustic instruments, voice and overhead etc.
|
|
|
Ultra low-noise transformerless FET input eliminates low-frequency distortion
|
|
Smooth, super-wide frequency response and incredible musicality
|
|
Switchable low-frequency roll-off and -10 dB input attenuation
|
|
Gold-plated 3-pin XLR output connector
|
|
Rugged construction with satin nickel-plated brass body
|
|
Custom microphone stand adapter, windscreen and transport case included
|
|
Manual Download |
| Large diaphragm cardioid microphone | | Pressure gradient transducer with with one-diaphragm capsule | | Transformerless circuitry | | Extremely low noise: 7 dB-A | | Includes swivel mount | | Straightforward handling for homerecording and professional studios | |
High-quality professional equipment for limited budgets
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 23 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1 kohms | | Equivalent noise level, CCIR1) | 17.5 dB | | Equivalent noise level, A-weighted1) | 7 dB-A | | Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) | 76.5 dB | | Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) | 87 dB | | Maximum SPL for THD 0.5%2) | 138 dB | | Maximum output voltage | 13 dBu | | Dynamic range of the microphone amplifier (A-weighted) | 131 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 3 mA | | Matching connector | XLR3F | | Weight | approx. 450 g | | Diameter | 60 mm | | Length | 132 mm |
|
|
| Variable large diaphragm microphone | | Pressure-gradient transducer with double membrane capsule | | The studio microphone classic | | Three directional characteristics: omni, cardioid, figure-8 | | Switchable low frequency roll-off | | Switchable 10 dB pre-attenuation | |
Ideal as main and as support microphone in the most differing recording situations
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Omnidirectional, cardioid, figure-8 plus | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 20/28/22 mV/Pa1) | | Rated impedance | 200 ohms | | Rated load impedance | 1 kohms | | Equivalent noise level, CCIR2) | 26/23/25 dB1) | | Equivalent noise level, A-weighted2) | 15/12/14 dB-A1) | | Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) | 68/71/69 dB1) | | Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) | 79/82/80 dB1) | | Maximum SPL for THD 0.5%3) | 117 dB (cardioid) | | Maximum SPL for THD 0.5% with preattenuation3) | 127 dB | | Maximum output voltage | 390 mV | | Dynamic range of the microphone amplifier (A-weighted) | 105 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 0.8 mA | | Matching connectors | XLR3F | | Weight | 500 g | | Diameter | 56 mm | | Length | 200 mm |
| |
The CK-7 houses a 35mm gold-sputtered thin Mylar capsule. The CK-7 uses high grade Polystyrene and Metalized Polypropylene capacitors in the audio path. This represents a commitment to quality, as these normally are the type of "upgrade" components that are implemented by microphone modders/hot-rodders! Any studio can proudly offer the CK-7 as a vocal mic or utility condenser due to its versatility...It exudes class visually as well as sonically.
Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability. The versatile CK-7 mic is able to produce professional results with a clean sonic character. The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results. The 3 patterns allow the CK-7 to be used in a variety of situations.
The cardioid pattern is generally best used on vocals and single instruments. The omni mode works well in incorporating some room sound into the track. The figure 8 pattern allows 2 vocalists to use the mic at the same time from opposite sides. The CK-7 has separate -10 dB pad & 80 Hz LF roll off switches....The -10dB attenuation switch can be engaged when miking very high SPL sources to keep from overloading the electronics. The 80Hz high-pass filter switch can be engaged to reduce rumble and to keep unwanted low frequencies from "muddying up" the track.
Applications.
studio vocals, acoustic guitar, mandolin, drum overheads, piano, room mic
Specifications
Type: True Condenser
Polar Pattern(s): Cardioid , Omni , Figure 8
Capsule: Dual-sided 35mm center-terminated gold-sputter Mylar (6 micron)
Frequency Response: 20-20,000 Hz +/- 3dB
Output Impedance: |
- One-inch large-diaphragm, true condenser cardioid transducer
- Rugged all-metal body
- Roadworthy construction
- Switchable 20 dB preattenuation pad
- Switchable bass cut filter
- Legendary AKG sound quality
- Designed and engineered by AKG in Vienna, Austria
- Comes with spider-type shock mount and aluminium carrying case
The Perception 220 is a large-diaphragm true condenser microphone offering outstanding build quality and excellent value. Its many useful features and included accessories make this microphone uncommonly versatile. It delivers a classic warm, clear sound and conforms to the stringent standards defined for AKG recording products. These standards are based on AKG΄s six decades of experience in making microphones and on input from sound engineers around the world who use AKG products every day.
Its 1-inch large-diaphragm true condenser transducer brings AKG studio quality to the project studio as well as all other areas of recording and live sound applications. A switchable bass cut filter and preattenuation pad make it perfectly suited even for use on loud sound sources producing sound pressure levels up to 155 dB SPL. The rugged and roadworthy design makes it also a perfect choice for on-stage applications. The Perception 220 comes with a spider-type shock mount and a rugged metal case. |
| Type |
1" Large Diaphragm True Condenser |
| Polar pattern |
cardioid |
| Frequency range |
20 to 20,000 Hz |
| Sensitivity |
18 mV/Pa (-35 dBV) |
| Max. SPL |
135 dB/155 dB (0/-20 dB) for 0.5% THD |
| Equivalent noise level |
16 dB-A (IEC 60268-4) |
| Signal/noise ratio (A-weighted) |
78 dB |
| Preattenuation pad |
0 dB, -20 dB |
| Bass filter |
12 dB/octave at 300 Hz |
| Impedance |
=1000 ohms |
| Current consumption |
|
|
|
The AVANTONE CK-6 is truly a gorgeous looking and sounding microphone. The design, character and performance can be compared directly to fine studio-standard FET mics…but at a fraction of their cost!
The rugged CK-6 microphone body and capsule assembly are precision machined of Brass. Aesthetically the compact body features an elegant Metallic Cabernet Wine-Red finish, accented with polished nickel trim and capsule assembly. Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability.
This Transformerless CLASS A FET Microphone w/ 32mm gold sputtered thin Mylar capsule is designed with circuitry that will yield pleasing professional results comparable to much more expensive designs. It also features -10 dB pad & 80 Hz LF roll off switches for varied recording situations.
The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results.
Applications
Studio vocals, acoustic guitar, mandolin, drum overheads, piano, etc…
Specifications
Type: True Transformerless Condenser
Polar Pattern: Cardioid
Frequency Response: 35-20,000 Hz +/- 3.5dB
Output Impedance: |
Reviews
There are no reviews yet.