MONTARBO E616A MONITOR ACTIVE 650W

E616A

Two-way activefull-range with DSP. 650 W.

2 x 6” woofers DʼAppolito config.

2.5” driver, 80° x 60° dispersion.

500 W + 150 W class-D power amplifier.

Optional: LD2.4 USB interface for remote PC connection

Product details
Woofer:    10-inch Paper Cone
Frequency response:    20Hz – 40Hz ~ 120Hz
Crossover frequency:    40-120Hz adjustable
Lf - Amplifier Power:    300W
Signal LF:    >90dB
THD + N @ Rated Power LF:     0.08%
Inputs:    2x XLR,2x TRS,
2x RCA Connectors,
S/PDIF Connector
for digital signal
Outputs:    2x XLR, 2x TRS
2x RCA Connectors, S/PDIF - RCA jack for digital signal thru
Input Impedance:    20 kOhm balanced, 10 kOhm unbalanced
Input Sensitivity:    +4 dBu (Balanced), -10dBV (unbalanced)
Phase reverse:    0° /180° switch
Available colors:    Red, Black
Gross Weight:    22.4kg / 49.2lb
Net weight:    18.7kg / 41.1lb
Gross Dimensions:    L500 x W523 x H523 mm
L19.68x W20.59 x H20.59 in
Net Dimensions:    L374 x W368 x H383 mm
L14.72 x W14.49 x H15.08 in

To hear what's really going on at the bottom of your mixes, you need a subwoofer that speaks the truth. The TemblorTM T10 lets you take charge of the low-frequency foundation of your mix with a combination of quality components and design, plenty of inputs and outputs, and extensive user controls not normally available in this price range.
Main components

• 10-inch glass-composite low-frequency transducer
• Front-firing, bass-reflex acoustic port
  

• Input gain control (-30 dB to +6 dB, continuously variable)
• Continuously variable lowpass filter (50 Hz to 130 Hz)
• Built-in crossover
• Switchable highpass filter removes frequency content below 80 Hz from the full-range signal sent from the T10 outputs to the main monitors
• Momentary footswitch (included) bypasses the subwoofer, highpass filter, and Sub Out
• Polarity invert and ground-lift switch
  

• 250 watt, Class AB amplification
• Internal damping and heat sink
• Integrated, gravity-calibrated rubber feet for stable placement
  

• Left and right, balanced XLR and ¼" TRS and unbalanced RCA main inputs
• Left and right balanced XLR and ¼" TRS outputs 
• XLR subwoofer output for connecting a second T10

The Genelec 7073A active subwoofer is a powerful and precise bass reproduction tool for large Surround Sound or Stereo installations. Its 19 Hz lower cut-off frequency and 124 dB sound pressure output capability are sufficient to handle the most demanding high SPL applications.

All electronics are integrated into the subwoofer cabinet: active crossover filters, driver overload protection circuits and power amplifiers.

The built-in bass management unit has six signal input and output channels (L/C/R Front and L/C/R Rear), LFE input and summed signal output connectors, providing great flexibility and easy connection.

The Sub6 is a large volume cabinet design, equipped with an 11" woofer and a rear laminar port. This configuration guarantees bass linearity whatever the intended SPL. The control board is extremely versatile, with connectivity which allows a 2.1, 2.2 and multichannel use via the L/R inputs and outputs and the LFE. The numerous settings such as the high-pass crossover dedicated to monitors, the adjustable phase and level control provide optimum coupling with the Solo6 Be and the Twin6 Be monitors. And finally, a small, but important point: the footswitch input. It enables one to connect a pedal to deactivate the subwoofer and the high-pass crossovers on the outputs that supply the monitors. This simplifies and greatly improves control during the different stages in monitoring.

Product details