Content |
- Aftermarket diaphragm D8R2406 replacement for the JBL 2406H-1 Driver or BMS 4538 and more models.
- Fits JBL MPRO 400 Series
- 8 Ohm
Polymer diaphragm replacement kit: 8ohm, 37.8mm (voice coil inner diameter)* 70.0mm (al ring outer diameter),aluminum round wire v/c
This aftermarket diaphragm is a direct replacement for the JBL 2406, 2406H, 2406-1, 2406H-1 driver / tweeter / horn.
Specifications
- Annular Ring Diaphragm
- 8 ohm
- Peak power 300 watts
- Frequency range 1200Hz - 30kHz
- Overall diaphragm diameter 2.75-in or 70-mm
- Voice coil diameter 1.5-in or 38-mm
- Diaphragm material is polyester
- Voice coil former is Kapton
- Voice coil wire is edge wound / flat wound, aluminum
Very easy to replace. This diaphragm self aligns. Simply remove the old diaphragm,
clean the voice coil gap with a piece of masking tape, then install the new diaphragm in
reverse order.
This diaphragm uses the polyester annular ring diaphragm and surround just like the
original JBL diaphragm.
This diaphragm will handle the same amount of power, and sounds the same as the
original JBL 2406 diaphragm, guaranteed! |
Genuine Celestion CDX1 Driver uses T5503/R Diaphragm in 1415, 1425, 1430. 8 ohms
This is also the replacement diaphragm for the HF Driver in the QSC HPR122i, HPR153i and HPR153F speaker box. Also fits Yorkville NX300and Yorkville NX55P, NX300, YX10, YX12, YX12M, YX15, YX15P, and YX215 cabs. |
Replacement diaphragm kit for 22XT driver
FOR HV1200, PR1500, 1522HC, CL-2, CL-1, 115 Int. Series III Oak, HKS-15, 115TF, 112TI, 115TI, HV1280, PR1280, SP2XT, SP4XT, SP5XT, DJS1800, 112SE, Impulse 200, SP2G, SP4G, SP5G, Impulse 200P 112DLM, 115DLM, SP112M, SP115M, Impulse 200 4 Ohm, SP3G, SP6G, Impulse 1280, 115CM, 115TF, Impulse 1282, HV1282, 112TLM, 115TLM, Impulse 200 8 Ohm, 1522TLS,Ιmpulse 500, DS1502, DS1803, DS3003, 1545TI, MF1-X/MK-3 Series, SP2Ti, SP4Ti, SP5Ti, 115 Int. HC, 118 Int. HC, 3020HT, 1245M, HDH-1, 112PS, HDH-4, 115TF Bleached Oak Enc., Impulse 500 4 Ohm Impulse 500P
| |
-
JBL Factory Speaker Diaphragm Part # D8R2418
-
Voice coil: 1-3/4" (45mm)
-
Diameter: 3" (75mm)
-
Length: 5-1/8" (130mm)
-
Impedance: 8 ohm, DCR: 4 ohm
-
Titanium dome with copper voice coil on Kapton former.
-
Fits JBL Driver and Cabinet Models:
JBL: 2418, JBL 2418H, JBL 2418H-1, 3622N, 3632M-HF, 3632M-HF-T, 3677S, 3722HF, 3722N-HF, 4425LR, AC2212/00-WH, AC2215/00-WH, CAB-55, CAB55, CAB 55, EON-15, EON15, EON 15, EON 15P-1/230, EON POWER15, EON-15-G2, EON15-G2, EON 15-G2, EON-15P, EON15P, EON 15P, MR-902, MR902, MR 902, ,MR-905, MR905, MR 905, MR-922, MR922, MR 922, MR-925, MR925, MR 925, MR-926, MR926, MR 926, MR-935, MR935, MR 935, MR-938, MR938, MR 938, MS-112-WH, MS112-WH, MS 112-WH, MS-115-WH, MS115-WH, MS 115-WH, and many more!
Please check your model before ordering to make sure you are getting the correct diaphragm.
|
- JBL Factory Speaker Diaphragm part # D8R2452-SL.
- Specs: Voice coil: 3.93" (100mm), Diameter: 5" (76mm), Impedance: 8 ohm, DCR: 4 ohmFits JBL: 5732-M/HF, HLA4895, VP7210-95DP, VP7212/64DPAN/CN/DA, VP7212/95DPAN/CN/DA, VP7212/95DPC, VP7212-MDP, VP7215/64DPAN/CN/DA, VP7215/95DPAN/CN/DA, VP7215/95DPC, VP7315/64DPAN/CN/DA, and many more!
|
Reviews
There are no reviews yet.