Content |
FEATURE SUMMARY
- iDR DSP system
- 16 processing channels (inputs and outputs)
- 2 analogue mic/line inputs on XLR with 20V phantom power
- 4 analogue line inputs on TRS jack
- 4 line outputs on XLR
- iDR-4ST version also available, with XLRs replaced by Euroblock (Phoenix) connectors
- 2 line outputs on TRS jack
- Digital audio expansion ports (8 channels in, 8 channels out)
- Hot Plug‘n’Play PL Series remote controllers
- High quality audio signal path and DSP processing
- Monitor with mouse and ripplethrough capability
iDR-4 and iDR-8 are 16 x 16 matrix mixers with an extensive array of audio management tools designed to reduce the need for additional devices for an installation, or carried in the hire inventory. Allen & Heath preamps, 24bit converters and fixed DSP architecture ensure that concert-quality low-latency sound is delivered efficiently to where it is needed. |
Shure DP11EQE Dynamics Processor Specification:
GENERAL:
Frequency Response: 20 to 20k Hz +/- 1.0 dB re 1 kHz
Dynamic Range: 104 dB minimum, A-weighted, 20 Hz to 20 kHz
Sampling Rate: 48 kHz
Digital-to-Analog, Analog-to-Digital Conversion: 20 bit resolution
Voltage Gain:
1 dB +/- 1dB (power off)
12 dB +/- 2 dB (input 10 dBV, output +4 dBu)
12 dB +/- 2 dB (input +4 dBu, output 10 dBv)
0 dB +/- 2 dB (equal input and output sensitivities)
Impedance:
Input: 47 kilohms +/- 20% actual
Output: 120 ohms +/- 20% actual
Input Clipping Level
+18 dBu minimum (at +4 dBu setting)
+6 dBV minimum (at 10 dBV setting)
Output Clipping Level
+18 dBu minimum (at +4 dBu setting)
+6 dBV minimum (at 10 dBV setting)
Total Harmonic Distortion
LED Signal Indicators
Signal: 40 dB
Clip: 6 dB down from input clipping
Propagation Delay from Input to Ouput
0.8 ms (all filters flat, no dynamics processing, 0 ms delay), up to 2.1 ms (all processing enabled)
Polarity
Input to output: inverting optional (default: non-inverting)
XLR: pin 2 positive with respect to pin 3
1/4-inch TRS: tip positive with respect to ring
Operating Voltage
DP11EQ: 120 Vac, 50/60 Hz, 50 mA max
DP11EQE: 230 Vac, 50/60 Hz, 25 mA max
DP11EQJ: 100 Vac, 50/60 Hz, 50 mA max
Temperature Range
Operating: 0 degrees to 60 degrees C (32 degrees to 140 degrees F)
Fuse
DP11EQ: 120 Vac. Fuse: 100 mA, 250V time delay
DP11EQE: 230 Vac. Fuse: 50 mA, 250 V time delay
DP11EQJ: 100 Vac. Fuse: 100 mA, 250 V time delay
Dimensions
219 mm x 137 mm x 44 mm (8-5/8 in x 5-3/8 in x 1-3/4 in)
Weight: 930 g (2.05 lbs)
DYNAMICS PROCESSOR
Gate and Expander:
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 1.0 to 200 ms
Decay: 0.05 to 1 second
Gate Hold Time: 0 to 0.5 seconds
AGC Leveler
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 0.2 to 3 seconds
Decay: 0.5 to 5 seconds
Hinge: Threshold to 1 dB, 0.5 dB resolution
Compressor and Limiter
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 1.0 to 200 ms
Decay: 0.05 to 1 second
Knee: Hard or Soft selectable
No Overshoot Peak Limiter
Propagation delay: 1 ms
Threshold: 72 to 1 dB, 0.5 dB resolution
Attack: 0 msDecay: 100 ms
PARAMETRIC EQUALIZER
Parametric Filter Frequency Bands
Up to 9 bands, variable frequency, variable Q
Boost/Cut Range
+6 dB to 18 dB per band
Q Range
1/40-octave to 2 octave
High and Low Shelf/Cut Filters
Shelf, +6 to 18 dB per filter
Cut, 12 dB per octave nominal
DELAY
Up to 1.3 seconds, 21 microsecond resolution
|
VIRTUALIZER 3D FX2000
High-Performance 3D Multi-Engine Effects Processor
71 breathtaking new algorithms—true RSM (Real Sound Modeling) stereo and 3D effects
Wave-adaptive virtual Room reverb algorithms for natural reverb and delay
Awesome modulation, dynamic, psychoacoustic and EQ algorithms
Authentic amp simulation, distortion and special effects
11 effect combinations with selectable serial / parallel configuration
Up to 7 adjustable parameters plus 2-band EQ per effect
24-bit A/D and D/A converters with 64/128-times oversampling
True stereo processing for realistic channel separation in stereo image
100 factory presets plus 100 user memory locations
Extensive MIDI implementation
Accurate LED level meters for perfect level setting and optimum performance
Servo-balanced XLR and ¼'' TRS inputs and outputs
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany
Reverbs & Delays
Because it is one of the most desired effects, the FX2000 provides 12 different reverb programs, so you always have the ideal reverb for your live performance or studio needs.
Reverbs include:
CATHEDRAL
GOLD PLATE
SMALL HALL
ROOM
STUDIO
CONCERT
STUDIO
STAGE
SPRING REVERB
AMBIENCE
EARLY REFLECTIONS
Specialty reverbs include:
REVERB – reverb is synthetically turned off after a predetermined amount of time
REVERSE REVERB – reverb envelope is reversed—it slowly gets louder
Delays include:
STEREO DELAY – delay is processed across the entire stereo image
TAPE ECHO – simulates classic tape echo devices, pre-dating the advent of digital delays
PING PONG – delay signal is "bounced” from left to right at an adjustable tempo
Much More than Just Reverb and Delay
The FX2000 has some of the best-sounding reverb and delay programs, but thatʼs not all. It also provides excellent modulation effects (such as chorus, flanger and phaser), including special variations like musical pitch shifter, tremolo and even a rotary speaker simulation.
Modulation and Pitch Shifter FX:
STEREO FLANGER (originally generated by playing back two synchronized "reel to reel” tape recorders with a finger rubbing on the flange of one of the take-up reels)
VINTAGE FLANGER simulates a guitar fl anger stomp box
JET STREAM FLANGER sounds like a classic analog flanger
STEREO CHORUS (combines a slightly detuned signal with the original)
ANALOG CHORUS simulates a guitar chorus stomp box
VINTAGE CHORUS imitates a classic analog studio chorus
ULTRA CHORUS creates the sound of an eight person chorus
STEREO PHASER (combines a second, phaseshifted signal to the original)
VINTAGE PHASER represents a guitar phaser stomp box
DUAL PHASER processes the left and right channels separately
ROTARY (simulation of the rotating speakers typically used on an organ) – Slow or Fast
PITCH SHIFTER (changes the pitch of the original signal) – can be used to create harmonies with the original signal or replace it entirely with the altered pitch. Choices include stereo, two and three vocal pitch shifter
VIBRATO – the peak frequency of the tone is periodically and uniformly changed (quickly or slowly)
TREMOLO (common vintage guitar amplifier effect) – a fast or slow periodic variation in volume
AUTO PANNING – signal is automatically sent from one side of the stereo image to the other, either once or multiple times
Dynamic FX:
COMPRESSOR – reduces the dynamic range of the signal, maintains consistent signal level and thus avoids distortion associated with excessive input levels
EXPANDER – effectively broadens the dynamic range of source signals while reducing background noise
GATED REVERB – helps reduce background clutter by turning reverb off below a predetermined threshold level. Particularly effective on drum mics and vocals
ANA. KOMPR/LIM. — similar to COMPRESSOR but with Limiting functionality
ULTRAMIZER – analyses incoming signal and automatically applies compression across two independent frequency bands
DENOISER – eliminates or reduces noise and other interference
DE-ESSER – reduces or removes sibilance (Ssss sound) from signal
WAVE DESIGNER – allows you to influence the envelope by adjusting Attack and Release of the signal
Psychoacoustic FX:
EXCITER – adds artificially generated overtones to the original signal, increasing presence and perceived loudness without significant increase in signal level
ENHANCER – functions much like a dynamic pitch equalizer
ULTRA BASS – sub-harmonic processor combined with bass exciter and limiter
STEREO IMAGER – divides the signal into middle and side signals, allowing individual signals to be amplif ed when desired and placed on the stereo image
ULTRA WIDE – creates a broader stereo image
BINAURALIZER – also creates a broader stereo image and compensates for crosstalk between both speakers
Filter/EQ FX:
AUTO FILTER – influences the frequency response of a signal. Two filters are included: low pass allows low frequencies to pass and suppresses high frequency content; high pass does the exact opposite
LFO FILTER - Controls the rate of oscillation effects
PARAMETRIC EQ – allows you to control the bandwidth, frequency and amplitude of a signal
GRAPHIC EQ – the sound spectrum is divided into eight (8) adjacent frequency bands, which can be cut or boosted, bandwidth is predetermined
Distortion FX and Amp Simulations
The FX2000 is also equipped with distortion, amplifier and speaker simulation including VOCAL DISTORTION, TUBE DISTORTION, GUITAR AMP, TRI FUZZ, SPEAKER SIMULATION, RING MODULATOR and LO-FI.
Special FX:
VINYLIZER – adds clicks and/or noise to the signal, reminiscent of old vinyl records and tape machines
SAMPLER – allows you to record and playback up to five (5) seconds of program material
VOCODER – allows the input signal to modulate another signal (usually a synthesizer sound), creating the familiar "talking synthesizer” effect
VOICE CANCELER – removes mono vocal parts from stereo recordings for "instant Karaoke”
RESONATOR – simulates and oscillating system that amplifies a specific frequency
Our FX Combinations Go to 11
Sometimes you want to add a little (or a lot) of color to your reverb and delay patches. The FX2000 allows you to layer modulation effects like chorus, flanger, pitch or tremolo with your reverb or delay selections.
FX Combinations include:
Chorus & Reverb
Flanger & Reverb
Leslie & Reverb
Pitch & Reverb
Delay & Reverb
Tremolo & Reverb
Phaser & Reverb
Chorus & Delay
Flanger & Delay
Pitch & Delay
Tremolo & Delay
Enhanced User Editability
Logical grouping of parameters, along with the combination of encoders, buttons, LEDs and an easily readable LED display, make operating the FX2000 a breeze. You are free to edit up to seven parameters per preset, and then save them for future use in the 100 provided memory locations.
Value
With its extremely powerful processing capability and versatile array of features, the FX2000 will become the busiest tool in your audio arsenal. Stop by your BEHRINGER dealer today and find out why more professional sound engineers are turning to the FX2000 as their primary FX processor— both in the studio and on the road.
| Bring a more professional sound to your mix
Adding a dbx® 266xs Compressor/Limiter/Gate to your live sound rig or studio gives you more dynamic control to help create a more polished, professional sound. Having compression in your audio chain gives you the ability to smooth out uneven levels, add sustain to guitars and fatten up your drums. It also makes it easy to bring vocals to the front of your mix - adding greater clarity and making them stand out from the surrounding instruments.
dbx knows compressors...after all we invented them! The 266xs is the latest in a long line of the world's most successful compressors from the inventors of the technology. Its patented Overeasy® compression technology provides smooth and musical performance while the AutoDynamic™ attack and release controls, found only on dbx compressors, puts great sound within easy reach. The 266xs can operate in stereo or dual-mono modes, has true RMS power summing and features quality XLR and 1/4" TRS inputs and outputs. It cuts no corners on visual feedback with gain reduction metering and easy-to-read backlit switches.
Features
- Error proof operation to smooth uneven levels, add sustain to guitars, fatten drums or tighten up mixes
- New gate timing algorithms ensure the smoothest release characteristics
- Program-adaptive expander/gates
- Great sounding dynamics control for any type of program material
- Separate precision LED displays for gain reduction, compression threshold and gate threshold allow quick, accurate setup
- Stereo or dual-mono operation
- Balanced inputs and outputs on 1/4" TRS and XLR connectors
- Side Chain insert
- Classic dbx® "Auto" mode
Specifications
Input Connectors |
1/4" TRS and female XLR (pin 2 hot) |
Input Type |
Electronically balanced/unbalanced, RF filtered |
Input Impedance |
40kΩ balanced/unbalanced |
Max Input |
>+22dBu Balanced or Unbalanced |
Output Connectors |
1/4" TRS, female XLR (pin 2 hot) |
Output Type |
Impedance-balanced/unbalanced, RF filtered |
Output Impedance |
+4dBu: 100Ω balanced, 50Ω unbalanced; -10dBu: 1kΩ balanced, 500Ω unbalanced |
Max Output |
>+21dBu balanced/unbalanced into 2kΩ or greater; >+18dBm balanced/unbalanced (into 600Ω) |
Sidechain |
1/4" TRS Phone, Normalled: Ring = Output (send); tip = Input (return) |
Sidechain Impedance |
Tip = >10kΩ (Input), Ring = 2kΩ (Output) |
Sidechain Max Input Level |
Tip = >+22dBu (Input) |
Sidechain Max Output Level |
Ring = >+20dBu (Output) |
Compressor Threshold Range |
-40dBu to +20dBu |
Compressor Threshold Characteristic |
Selectable OverEasy® or hard knee |
Compressor Ratio |
1:1 to Infinity:1 |
Compressor Attack Time |
Scalable Program-Dependent AutoDynamic™ |
Compressor Release Time |
Scalable Program-Dependent AutoDynamic™ |
Expander/Gate Threshold Range |
-60dBu to +15dBu |
Expander/Gate Ratio |
1:1 to 4:1 |
Expander/Gate Attack Time |
|
| SHARK FBQ100
Automatic Feedback Destroyer with Integrated Microphone Preamp, Delay Line, Noise Gate and Compressor
High performance single channel Feedback Destroyer with integrated microphone preamp, delay line, noise gate and compressor
Automatically and "intelligently" locates and destroys up to 8 feedback frequencies
Narrow FBQ filters for extremely effective feedback suppression, while keeping highest sonic quality
Ultra-low noise Mic/Line input with Gain control and +48 V phantom power
Delay line with up to 2.5 seconds of delay, adjustable in meters, feet and msec
Noise gate with automatic and manual parameter settings
Automatic compressor with variable density
Subsonic filter with adjustable cut-off frequency
Balanced inputs and servo-balanced outputs with ¼'' TRS and gold-plated XLR connectors
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany |
Interactive Reference-Class 2-Channel Expander/Gate/Compressor/ Peak Limiter with
Integrated De-Esser, Dynamic Enhancer, Tube Simulation and Low Contour Filter
Whether you?re recording, mixing or mastering, the COMPOSER PRO-XL MDX2600
gives you total dynamic control. It includes all of the features you would expect from
a reference class compressor?plus a voice-adaptive de-esser, a new dynamic
enhancer, authentic tube emulation and much more. These are some of the indispensable
tools for producing clean, consistent audio with virtually no loss in signal quality.
Features:
Switchable IKA (Interactive Knee Adaptation) program-adaptive compression circuitry
combines the advantages of hard-knee and soft-knee characteristics
Integrated de-esser with switchable male/female voice recognition removes excessive
sibilance from your vocal tracks
IGC (Interactive Gain Control) peak limiting circuitry combines clipper and program
limiter for reliable and inaudible protection against signal peaks
Switchable dynamic enhancer for brilliant, lively audio even with heavy compression
IRC (Interactive Ratio Control) expander/gate circuitry for virtually inaudible
noise suppression
Switchable tube simulation for the extra warmth and transparency of classic
tube circuitry
Automatically or manually adjustable attack and release times
Switchable low contour filter prevents "pumping" due to low-frequency
dominated compression
Stereo couple function with independent output level settings
Switchable side chain input with side chain monitor function
Ultra low-noise 4580 operational amplifiers and state-of-the-art THAT¬ VCA's
Separate 12-segment LED meters for input/output levels and gain reduction
Dedicated "traffic light" threshold and de-esser level displays
High-quality detented ALPS¬ potentiometers and illuminated switches
Servo-balanced inputs and outputs with ? in. TRS and gold-plated XLR
connectors
Relay-controlled hard bypass switch with auto bypass function in case
of power failure
Manufactured under ISO9000 certified management system
|
Reviews
There are no reviews yet.