VOX AMPLUG 2 BL Mini amplifier for guitar headphones

Mini amplifier for guitar headphones with advanced analogue modeling simulation of authentic crunchy blues tone with cranked tweed amp. AUX input for connection to an external audio source. Operation with 2xAAA batteries.

Specifications
General

Frequency response
    

 
    

20 Hz - 20  kHz (+0 dB, -1.5 dB)

Signal-to-noise ratio
    

 
    

100  dB (IHF A-weighted, input level control min.)

Channel separation
    

 
    

80 dB between adjacent channels

Line input
    

 
    

Front: 6.3 mm jacks, unbalanced
Rear: RCA connectors, unbalanced

   Input impedance
    

 
    

40 kOhm

   Nominal level
    

 
    

-10 dBV (0.3 V)

Headphone outputs
    

 
    

four 6.3 mm stereo jacks

   Maximum output power
    

 
    

2 x 1.5 W at 8 Ohm (1 channel in use)
2 x 1,2 W an 8 Ohm (four channels in use)

Power supply
        

230 V AC, 50 Hz

Power consumption
    

 
    

10 W

Dimensions (W x H x D)
        

482  mm x 44  mm x 196  mm

Weight
    

 
    

4 kg

The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.

In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.

The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.

Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.

The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.

INPUT:    1 audio stereo, 1Vpp/50kΩ on a 6.5mm stereo phone socket.
OUTPUTS:    5 audio stereo, 500mW/8Ω on 6.5mm stereo phone sockets.
AUDIO BANDWIDTH (-3dB):    25kHz.
CONTROL:    5 stereo output level controls (front), 1 mono switch (rear).
GAIN RANGE:    -60dB to +10dB.
S/N RATIO:    78dB.
THD:    0.08% @100mW.
POWER SOURCE:    12V DC, 370mA nom, 1A max.
DIMENSIONS:    16.5cm x 12cm x 4.5cm (6.5” x 4.72” x 1.77”) W, D, H.
WEIGHT:    0.68kg (1.5lbs) approx.
ACCESSORIES:    12V DC power supply.
OPTIONS:    RK-1 19" rack adapter.

The compact HX-3 Headphone Distribution Amplifier is the perfect accessory to quickly provide three high-performance stereo headphone feeds with individual level controls from line-level sources. The HX-3 can produce very high headphone levels with extremely low noise and distortion.

Great for radio, television, film, and music production applications, the battery-powered HX-3 accepts balanced XLR line-level inputs or unbalanced 1/4-inch and 1/8-inch stereo inputs. Its 1/4-inch loop-out can connect multiple HX-3's for additional headphone outputs. Headphones are connected to panel-mounted 1/4-inch stereo connectors.

The HX-3 has a durable aluminum chassis to withstand the punishment of field and studio environments. The unit is powered by inexpensive batteries (two-AA) or external 5-18 VDC.

The HX-3 can add headphone outputs to the 552, 302, MixPre-D, MM-1, and USBPre-2.

• Three isolated headphone outputs with individual volume controls.
• 125 dB dynamic range with flat frequency response.
• Durable 1/4-inch connectors, panel mounted for strength.
• Stereo or mono monitoring.
• Peak LED indicates headphone overload.
• Two balanced XLR line level inputs or unbalanced 1/4-inch and 1/8-inch stereo inputs.
• Loop Output to connect additional HX-3's in series.
• All-metal connectors solidly mounted to the chassis for durability and RF immunity.
• Free from "Pin-1" grounding problems.
• Internal battery-power for up to 18 hours from two AA alkaline batteries.
• Chassis-isolated 5 to 18 VDC input for easy external DC powering.
• Power LED indicates low battery power.
• High strength, extruded aluminum chassis with protective metal end panels.

The amPlug Twin rolls back the years to capture the sound of the legendary clean American dual speaker combo tube amp. Noted for its sparkling and sustained clean sound, this amp has been is widely used in many genres - rock, blues, jazz, country, and more. Raising the gain provides a powerful American tube overdrive sound. A stereo chorus effect is built into the amPlug Twin, adding natural spaciousness and depth to the sound. As you play these sounds, you're sure to forget the passage of time, and lose yourself in the tones loved by musicians in styles such as jazz, country, and blues.
Specifications

• Controls: Gain, Tone, Volume; STANDBY/ON/FX switch
• Terminals: PHONES Jack (stereo), AUX In Jack (stereo)
• Power supply: AAA batteries (x 2)
• Battery life: amPlug Twin (FX on):
• With zinc-carbon batteries: approximately 3 hours
• With alkaline batteries: approximately 11 hours
• Dimensions (W x D x H): 86 x 80 x 31mm/3.39" x 3.15" x 1.22“
• Weight: 40 g/1.41 oz. (not including batteries)
• Included items: AAA batteries (X2) (for verifying operation)