Content | As a part of APartʼs revolutionary series of convection cooled power amplifiers, Champ-4 is an amplifier without cooling fans. Its four discrete AB-class amplifiers deliver high quality musical sound, high dynamics, and high reliability - all in a one-unit 19” enclosure.
No fan
Power amplifiers have to operate in demanding circumstances. Places where the air is full of dust, nicotine or grease. Because power generates heat, power amplifiers typically have fans to keep their electronic circuits cool. Unfortunately, these cooling fans are a major headache in the use of high-power amplifiers. They tend to be noisy, and if -or rather, when- the fan breaks down because of dust collection, the amplifier overheats and ultimately fails. A fanless amplifier seems the logical thing, but -until now-, the idea never seemed to work for high quality amps with high output power. Thus, installers stick to fan-cooled models and get out of bed to replace a fried amplifier ….
Unique design
Especially for the CHAMP-series, APart introduces unique, custom-designed side mount heat sinks. In combination with a self-supporting low resonance frame, they make it possible to create a discrete power amplifier without a noisy and dust-collecting fan inside the enclosure. This means: less maintenance, no annual fan or dust filter exchange procedure, no more amplifier cleanout, and no more unwanted noise from cooling fans. Because of this, Champ-4 can rely on convection cooling only! Champ-4 has a torsion-free front in solid brushed aluminum. The removable brackets have a special fixation system that allows easy removal but still assures extraordinary-strength fixation. This makes it possible to use the unit rack mounted as well as freestanding. On the rear side of the unit the user will find solid binding posts and 4 sets banana screw plugs included.
APC power management circuitry gets the best out of an amplifier
APC power management circuitry has been designed especially for Champ series amplifiers. It is one of the most intelligent amplifier protection circuits ever designed, simply because it does the job without interfering with the typical dynamic character of music. APC allows the user to preset the power potential of the amplifier, while maintaining high power reserves and thus producing high, clean power. It constantly analyses incoming music signals and keeps dynamics alive. An additional ultra fast peak limiter avoids amplifier clipping. With APC, your system is always in control, including your speakers.
Bridging amplifiers and bridging channels
It is possible to bridge two channels of the Champ-4. By doing this you unite the power of two smaller amplifier channels into a more powerful amplifier channel. The resulting power is usually more than double the power of both amplifiers used individually with the same load. Check the user manual for instructions on how to proceed. Champ-4 is a four-channel amplifier. If you want to use a subwoofer, it is possible to bridge two of the channels for use as a subwoofer channel. The two remaining channels can be used for the top speakers.
It is the ideal solution to create a small music system for small dance floors or parties. As it is equipped with a X-over, you end up having a superior, yet easy-to-use sound system. The striking design and technical innovations of the Champ series are setting new industry standards….whether it is for AV, studio, gigs, home or catering applications: experience the pure musical power of CHAMP-4!
Type Power amplifier
Power Bridge-mono 8 ohm 230W, 8 ohm/ch 75W,4 ohm/ch 125W
Frequency Response 20 Hz - 40 kHz
Inputs RCA
Οutput 4 x binding post
THD
Special Items -
Dimensions (W x H x D) 48.3 x 4.4 x 36 mm (W x H x D)
Rack Mount -
Weight 7.5 kg |
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
| - 6CH 60W DIGITAL AMPLIFIER
- LIGHT WEIGHT
- 6 BUS BROADCASTING FUNCTION WITH A UTP (CATEGORY 5) CABLE.
- VOLUME AND 5 BAND EQ TUNING FUNCTION BY CHANNEL
- AMP ID AUTO/MANUAL ALLOCATION FUNCTION
- SELF-BROADCASTING FUNCTION USING A LOCAL INPUT
- INTERFACE FUNCTION WITH OTHER EQUIPMENT USING A CONTROL INPUT/OUTPUT CONTACT
- Manufacturer: INTER-M
- Category: AMPLIFIERS
- Use: POWER AMPLIFIERS 100V
- Measurement Unit: Attribute34381
- Warranty Months: 12
- Depth (cm): 38.0
- AC Line Voltage and Frequency Configurations Available: 220-240VAC DC24V
- Height (cm): 8.8
- Weight (Kg): 13.0
- Order Quantity: 1
- Power Output: 60
- Rack Installation Possible: Yes
- Channels: 6
- Power Output W/4Ω: 60
- Frequency Response (at 1W, 4/8Ω) (dB) ±: 80Hz-20KHz
- Catalog: Professional
- Amplifier Type: Power Amplifier
- Load Impedance: Ohm
- Group: Attribute49042, Attribute50583
- Width (cm): 48.2
|
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
The DPA series amplifiers are digital power amplifiers designed to meet the specialized needs of sound contractors for Multi-Zone distributed speaker systems. They are designed in six different models of Class D power amplifiers, divided in three different architectures to meet the requirements for all kinds of applications.
They combine the best of all features in one single series of amplifiers, providing an outstanding sound quality with all the known advantages of Class D Amplifiers. Such as the excellent efficiency and very low heat dissipation. And due to the complete passively cooled entity only a minimal of maintenance is needed, while ensuring maximum reliability.
The small size of a single rack space make them very interesting for fixed rack mount as well as mobile applications.
The DPA74 is built as multi channel power amplifier with four individual controllable channels containing various specific features and advanced protection circuitry which protects against DC malfunctioning, short circuit, overheating and overload.
The signal input connections are accommodated with balanced XLR connectors. The operation mode can be selected between Stereo mode, Bridge mode and Parallel mode. The output connections are accommodated with Euro-Terminal blocks.
- Model Name / Type: DPA74 / Digital Amplifier
- 8 ohms: 4 x 50 W
- 4 ohms: 4 x 75 W
- 8 ohms Bridge: 2 x 150 W
- THD+N:
- Signal / Noise: > 100 dB
- Frequency Response: 20 Hz - 20kHz
- Power Supply: 240 V AC / 50 - 60 Hz
- Dimensions (W x H x D): 483 x 44 x 300 mm
|
The XM series multi-channel power amplifiers are ideal for theater, hall, and conference room installations. The lineup includes 80W × 4 and 180W × 4 models, meeting the needs of a wide variety of installed systems. The XM amplifiers are a compact 2U size and surprisingly lightweight, making them easy to handle and install. Switching power supplies deliver high output power while minimizing the unit's physical size. The XM series has monitor/remote jacks that allow external devices to be connected for status monitoring or control from a remote location.
Dimensions (W x H x D): 480 x 88 x 412 mm, Weight: 10 kg
Four high-power channels. Switchable stereo, parallel, or bridged operation. Versatile connectivity and high-pass filters for a variety of applications. Distribution drive capability for parallel multi-speakers systems (XM4180).
Monitor/Remote connector for remote monitoring and control.
|
Reviews
There are no reviews yet.